SIIG JU-VG0311-S1 Bedienungsanleitung
1
USB 3.0 Display Adapter
Quick Installation Guide
04-0817A
Introduction
The USB 3.0 Display Adapter allows you to connect
a monitor, LCD or projector to your desktop or
notebook PC and use it as an extended desktop or
as an additional larger/different display for your
main screen.
Key Features and Benefits
• Compliant with Universal Serial Bus 3.0
Specification
• Works with standard and wide screen
monitors
• Supports high resolutions up to 2048 x 1152
• Video streaming is supported up to 1080p
• Display modes: Primary Display, Extend,
Mirror
• Connect up to 6 USB display adapters
simultaneously
2
System Requirements
• Desktop or notebook PC with a single core
1.2 GHz CPU or faster
• An available USB 2.0/3.0 port (USB 3.0
recommended)
• Windows®
8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / XP (32-bit, SP3)
Package Contents
• USB 3.0 Display Adapter
• Driver CD
• DVI to VGA adapter (For JU-DV0311-S1
only)
• Quick installation guide
Layout
JU-DV0311-S1
Figure 1: USB 3.0 to DVI/VGA Pro - with DVI Output
DVI out
USB 3.0 connector
3
Windows Software Installation
Make sure the proper driver for your graphics
card is installed, the USB 3.0 Display Adapter is
not designed to work with Windows' Standard
VGA Graphics Adapter driver. Important: Do
not plug the USB 3.0 Display Adapter into the
computer until instructed to do so.
Figure 3: USB 3.0 to VGA Pro
Figure 2: USB 3.0 to DVI/VGA Pro - with VGA Output
JU-VG0311-S1
DVI to VGA adapter VGA out
USB 3.0 connector
VGA out
4
1. Insert the driver CD.
2. At the autoplay CD driver window, double
click Setup. Or press Windows key and R,
type D:\Setup.exe in the Run window,
then click OK. (Change D: to match your
CD/DVD-ROM drive letter)
3. Click Yes or Allow at the User Account
Control. Skip this step if not prompted.
4. Click I Accept.
5. Connect your second monitor to the USB
3.0 to Display Adapter and turn it on, then
plug the USB 3.0 Display Adapter into the
computer. (USB 3.0 recommended)
6. Restart the computer.
To Verify Windows Installation
1. Go to Device Manager to verify installation.
For Window 8 / Windows 7 / Windows XP:
Right click Computer or My Computer,
click Manage, then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
5
2. Double click USB Display Adapters.
For USB 3.0 to VGA Pro: USB3 VGA Adapter
should be displayed.
For USB 3.0 to DVI/VGA Pro: USB3 DVI
Adapter should be displayed.
Uninstalling the Adapter Driver
Windows 8 / Windows 7
1. For Windows 8, double click Control Panel
on desktop. For Windows 7, click Start, and
click Control Panel.
2. Click Programs, and click Programs and
Features.
3. Select DisplayLink Graphics, then click
Uninstall.
4. Click Yes, Yes, then click OK.
5. ClickYes tocompleteuninstallingthedriver.
Windows Vista
1. Click Start, and click Control Panel.
2. Click Classic View, double click Programs
and Features.
6
3. Select DisplayLink Graphics, then click
Uninstall, then click Yes.
4. Click Allow, then click Yes to complete
uninstalling the driver.
Windows XP
1. Click Start, and Control Panel.
2. Double click Add/Remove Programs.
3. Select DisplayLink Graphics, click
Remove, then click Yes.
4. ClickYes tocompleteuninstallingthedriver.
Windows Display Utility
After successful driver installation, a display
utility icon will appear in the taskbar. This
display utility allows you to quickly change the
viewing modes and resolutions. Access the utility
by clicking the icon.
Viewing Modes
Several options to change the setups of your
display:
•Screen Resolution: Displays a list of
available resolutions.
7
•Screen Rotation:
Normal - No rotation is applied to the USB
3.0 Display Adapter display.
Rotated Left - Rotates the extended or
mirrored display by 270 degrees.
Rotated Right - Rotates the extended or
mirrored display by 90 degrees.
Upside-Down - Rotates the extended or
mirrored display by 180 degrees.
•Extend to:
Right - Extends the display to the right of
the main display.
Left - Extends the display to the left of the
main display.
Above - Extends the display above of the
main display.
Below - Extends the display below the main
display.
• Extend (default): This mode extends your
desktop for easy viewing of multiple
windows. Windows will move off the
primary display from the right side and
enter the extended display from the left.
8
•Set as Main Monitor: This mode, makes
the USB 3.0 Display Adapter the main display
adapter in the system.
•Mirror: In this mode, the USB 3.0 Display
Adapter will mirror your desktop. You will
see the same image on both monitors.
•Off: This setting turns off the USB 3.0 Display
Adapter.
•Optimize for Video (not available in
Windows XP): Configures the secondary
display for optimum full screen video
performance output. Note: Text may appear
less clear.
•Fit to TV: Adjust the size of the Windows
desktop when the Windows desktop does
not completely appear on the TV.
Using Windows Display Properties (WDP)
Note: Not all of the WDP functions are
available in Windows Vista.
Instead of using the display utility, you can use
the embedded Windows Display Properties
(WDP) to change view modes and resolutions.
9
Following the instructions below to access the
WDP functions:
Position the mouse anywhere on the Windows
Desktop,
For Windows 8 / Windows 7: Right click and select
Screen Resolution.
For Windows Vista: Right click and select
Personalize, then click Display Settings.
For Windows XP: Right click then select Properties.
WDP allows you to rotate, duplicate or extend
screens as well as modify screen resolution.
•Display: Use the drop down list to select a
display to be configured.
•Resolution: Use the drop down list and
user the slider to choose a resolution.
•Orientation:
Landscape - Sets the display to landscape
view.
Portrait - Sets the display to portrait mode.
Landscape (flipped) - Setsthe display to upside
down landscape mode.
10
Portrait (flipped) - Sets the display to upside
down landscape mode.
•Multiple displays:
Duplicates these displays - Reproduces the
main display on the second display.
Extend these displays - Extends the main
display onto the secondary display.
Show Desktop only on 1 - The desktop appears
onthedisplay marked 1. The display marked
2 becomes blank.
Show Desktop only on 2 - The desktop appears
onthedisplay marked 2. The display marked
1 becomes blank.
•Make this my main display: When you
check the box, it will make your USB 3.0
Display Adapter the main display adapter
in the system. Make sure the secondary
monitor is selected before choosing this
option.
• Display Positions: To move the position of
a display, click and hold the display you
wish to move then drag it to the desired
position. (As Figure 4 in the next page.)
Inhaltsverzeichnis
Andere SIIG Adapter Handbücher
SIIG
SIIG 2-Port USB to RS-232 Serial Adapter Bedienungsanleitung
SIIG
SIIG JU-NE0B11-S1 Bedienungsanleitung
SIIG
SIIG Universal DC Power Adapter - 90W Bedienungsanleitung
SIIG
SIIG M1 Bedienungsanleitung
SIIG
SIIG JU-NE0411-S1 Bedienungsanleitung
SIIG
SIIG JU-NE0711-S1 Produktinformationsblatt
SIIG
SIIG CN2502 Bedienungsanleitung
SIIG
SIIG JJ-P20511-S3 Bedienungsanleitung
SIIG
SIIG CE-H23R11-S1 Bedienungsanleitung
SIIG
SIIG Cool Dual SATA to USB 2.0 Docking Bedienungsanleitung
SIIG
SIIG JU-AV0012-S1 Bedienungsanleitung
SIIG
SIIG PCI Express Serial Bedienungsanleitung
SIIG
SIIG Wireless-N CardBus Adapter Bedienungsanleitung
SIIG
SIIG YN6181 Bedienungsanleitung
SIIG
SIIG Aluminum Mini DisplayPort 1.2 to VGA Adapter... Bedienungsanleitung
SIIG
SIIG NN26 Series Bedienungsanleitung
SIIG
SIIG JU-NE0211-S1 Bedienungsanleitung
SIIG
SIIG JU-H20511-S1 Bedienungsanleitung
SIIG
SIIG ID-SB0111-S1 Produktinformationsblatt
SIIG
SIIG JJ-CFTS11 Bedienungsanleitung
