SIIG Cyber I/O PCI Bedienungsanleitung

2-1

Installation

Chapter 2

Installation

This chapter will guide you through the installation of your

Cyber I/O PCI. There are no jumpers or switches to set for this

PCI Plug-n-Play board.

2-1 Installing the

Cyber I/O PCI

Proceed with the following instructions to install the board in

your computer. General installation instructions are given

since the design of computer cases varies. Refer to your

computer’s reference manual whenever in doubt.

Note: Leave the Cyber I/O PCI board in its

static-resistantbaguntilyouarereadytoinstallit.

1. Turn OFF the power to your computer and any other

connected peripheral devices. Follow the precautions for

static electricity discharge.

CAUTION: STATIC ELECTRICITY DISCHARGE

may permanently damage your system. In order to

avoid possible static electricity discharge during

installationprocedures,pleasefollowtheguidelines

below:

•Dischargeanystaticelectricitybuildupinyourbodyby

touching a large grounded metal surface such as the

computer case (if plugged in), a metal window frame,

refrigerator, or water tap for a few seconds.

•During installation procedures, avoid any contact with

internal parts. Handle cards only by their edges.

CAUTION: Disconnect the AC power source

before removing the cover.

2-2

Cyber I/O PCI User's Manual

2. Unplug the power cord from the back of the computer.

3. Remove the computer’s cover.

4. Select an available 32-bit PCI slot for the new board.

5. Remove the selected slot bracket by unscrewing the hold-

ing screw and sliding it out. Save this screw for securing

the Cyber I/O PCI after it’s installed.

Fig. 2-1. Remove the Slot Bracket

6. To install the Cyber I/O PCI, carefully align the board’s

bus connector with the selected expansion slot on the

motherboard. Push the board down firmly, but gently,

until it is well seated.

2-3

Installation

NOTE: Hold the card by its external edges

only. Try to avoid touching the components,

connectors or pins.

Fig. 2-2. Install the Cyber I/O PCI

7. Replace the slot bracket's holding screw to secure the

board to the rear slot panel.

8. Replace the computer's cover.

9. Reconnect the power cord and make new connections to

the ports

The hardware installation is now complete. Continue to the

next section for the installation of the driver and utility files.

2-4

Cyber I/O PCI User's Manual

2-2 Installing the Drivers and Utilities

This section provides information on how to install the

Cyber I/O PCI's drivers and utilities for the following

operating systems:

Windows 95/98

Windows NT 4.0

DOS/Windows 3.x

IMPORTANT

Make sure you have installed the Cyber I/O PCI

in your system BEFORE installing the software.

2-2.1 Windows 95 & 98 Driver Installation

Perform the following steps to install the drivers for

Windows 95/98:

1. When you first turn on your computer after installing the

Cyber I/O PCI card, Windows will notify you of “New

Hardware Found”. From the choices listed on the screen,

select:

“•Driverfromdiskprovidedbyhardwaremanufacturer”

and click OK.

2. Insert the Driver Installation diskette in the floppy drive

and click OK.

3. Make sure the path in the command line window is

A:\. Then, click on OK to install the driver files.

4. Remove the diskette and select Yes to restart your

computer to finish setting up the new hardware.

To verify successful installation:

1. Fromthemaindesktop,clickonMyComputer,then double-

click on Control Panel, System, and Device Manager.

2. Double-click on SIIG Cyber PCI device options. SIIG

Cyber I/OPCIBoardshouldbedisplayedwhensuccessfully

installed. The port is ready to connect your new device.

2-5

Installation

2-2.2 Windows NT 4.0 Driver Installation

The Windows NT 4.0 drivers and associated files reside in

the NT subdirectory on the Driver Installation diskette.

Perform the following steps to install the Windows NT 4.0

drivers:

1 Boot up from Microsoft Windows NT 4.0.

2. Insert theDriver Installationdiskette in the floppy drive.

3. From the desktop, double-click on My Computer, then

3 1/2 Floppy (A:) and NT subdirectory.

4. Double-click on the setup icon. When the program

opensto the“SIIGCyber PCIWelcome” window,clickon

Next to continue.

5. From the “Choose Destination Location” window, click

Next to install the driver files in the default folder. Or

click Browse to change, then click Next to proceed.

6. From the next “Setup Complete” window, click Finish.

7. Remove the diskette and click on Finish to reboot your

system.

To verify successful installation:

1. From the main desktop, click on My Computer, then

Control Panel.

2. Double-click on the SIIG Cyber PCI icon. The assigned

system configuration will be displayed.

Note: During system startup after installing the

board, a non-conflicting system setting such as

COMport andbaseI/O addresswillbe assigned.

Ifyouliketochangeittoaspecificsetting,youcan

override the assigned setting by going into the

Control Panel, SIIG Cyber PCI, Settings, then

Advanced to change it.

2-6

Cyber I/O PCI User's Manual

2-2.3 DOS/Windows 3.x Utilities

For DOS support, run the dosinst.bat file to copy DOS

driver files cb10xpc.exe, cb10xsu.exe and dosinst.bat to

subdirectory c:\siig\cb10x>on drive C.

1. Insert Driver Installation diskette in the floppy drive.

2. From the C:\> prompt, type a: and press <Enter>.

3. From the A:\> prompt, type cd dos and press <Enter>.

4. From the A:\DOS> prompt, type dosinst and press

<Enter> to copy the files to subdirectory c:\siig\cb10x.

5. Remove the floppy diskette and reboot the system.

2-2.4 DOS Utilities

The following two DOS utilities are provided in the DOS

subdirectory of the Cyber I/O Driver Installation diskette:

CB10xpc.exe Display the current configuration setting of

the speed of baud rate for the serial port and

theI/Oportaddressandmodesettingsforthe

parallel port.

CB10xsu.exe Change the speed of baud rate for the serial

port and the mode settings for the parallel

port.

Youcan runeither utilitiesfrom thediskette, orcopy themto a

subdirectory on your hard drive.

CB10xpc.exe

The default baud rate for your Cyber I/O PCI's serial port is

115.2Kbps. AndtheI/Oportaddressandmodesettingforthe

parallel port are automatically assigned during the system's

startup. If you like to view the current system configuration

setting for the Cyber I/O PCI, proceed with the following

instructions to run the CB10xpc.exe:

2-7

Installation

CB10xsu.exe

Speed Change

The default baud rate for your Cyber I/O PCI's serial port is

115.2Kbps. If you connect a higher speed device, you may

change the baud rate to support up to 460Kbps.

Note: To switch to 460Kbps only when using

a device that supports a baud rate faster than

115.2Kbps. Any device supports the speed

less than 115.2Kbps should be kept at default

setting.

Perform the following steps to change the baud rate speed:

1. Go to My Computer in Windows 95 and click on the

subdirectory where the DOS utility files are stored. If it is

from the floppy disk, insert Driver Installation diskette and

double-clickon“31/2Floppy(A:)”andpress<Enter>.Then

double-click on the “DOS” folder and press <Enter>.

2. Double-click on the file cb10xsu.exe and press <Enter>.

The first screen displays the current mode setting, for

example: Parallel 1, EPP(1.9)/ECP.

3. To change the mode setting, type the letter “C” and press

<Enter>.

4. Type "H" and press <Enter> to change to high baud rate.

5. Type "Q" and press <Enter> to quit.

6. Restart your system for the change to take effect.

• Go to My Computer in Windows 95 and click on the

subdirectory where the DOS utility files are stored. If it is

from the floppy disk, insert Driver Installation diskette and

double-click on “3 1/2 Floppy (A:)”, the “DOS” folder and

the file cb10xpc.exe to display the current settings.

2-8

Cyber I/O PCI User's Manual

Mode Change

Your Cyber I/O PCI supports EPP/ECP, ECP, EPP, and

BPP/SPP modes. The default mode setting is EPP/ECP.

You can change the mode by running cb10xsu.exe.

1. Go to My Computer in Windows 95 and click on the

subdirectory where the DOS utility files are stored. If it is

from the floppy disk, insert Driver Installation diskette and

double-clickon“31/2Floppy(A:)”andpress<Enter>.Then

double-click on the “DOS” folder and press <Enter>.

2. Double-click on the file cb10xsu.exe and press <Enter>.

The first screen displays the current mode setting, for

example: Parallel 1, EPP(1.9)/ECP.

3. To change the mode setting, type the letter “C” and press

<Enter>.

4. Typeinthenumbercorrespondingtothemodeyouwantto

changeto,such as“4”forBPP/SPP andpress<Enter>.The

screen will display the change.

5. Type “Q” and press <Enter> to quit.

6. Restart your system for the change to take effect.

Inhaltsverzeichnis

Andere SIIG Computerhardware Handbücher

SIIG

SIIG JJ-PCM012-S2 Bedienungsanleitung

SIIG

SIIG DP SoundWave 4 Channel PCI Bedienungsanleitung

SIIG

SIIG Single-Serial PC Card Bedienungsanleitung

SIIG

SIIG Hi-Speed ExpressCard CF R/W Bedienungsanleitung

SIIG

SIIG JU-EP0012-S1 Bedienungsanleitung

SIIG

SIIG UltraATA 100 Pro Bedienungsanleitung

SIIG

SIIG NN-EC2812-S1 Bedienungsanleitung

SIIG

SIIG JU-PCM422-S2 Bedienungsanleitung

SIIG

SIIG CyberSerial POS 4000RJ Bedienungsanleitung

SIIG

SIIG USB 2.0 5-Port PCI Bedienungsanleitung

SIIG

SIIG SC-SAE612-S1 Bedienungsanleitung

SIIG

SIIG NN-403P12 Bedienungsanleitung

SIIG

SIIG CyberParallel ExpressCard Bedienungsanleitung

SIIG

SIIG I/O Expander 2S Bedienungsanleitung

SIIG

SIIG ExpressCard/54 CF R/W Bedienungsanleitung

SIIG

SIIG ExpressCard 11-in-1 Reader/Writer Bedienungsanleitung

SIIG

SIIG IO1037 Bedienungsanleitung

SIIG

SIIG DP PCI-to-PS/2 Bedienungsanleitung

SIIG

SIIG 1 FireWire 800 CardBus DV-Ki Bedienungsanleitung

SIIG

SIIG Dual Profile Hi-Speed USB 4-Port PCI Bedienungsanleitung

SIIG

SIIG SC-SAEE12-S1 Bedienungsanleitung

SIIG

SIIG SC-SB6412 Bedienungsanleitung

SIIG

SIIG SATA II-150 PCI Bedienungsanleitung

SIIG

SIIG Serial ATA 4-Channel PCI Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung