SIIG SC-SB6412 Bedienungsanleitung

Introducing the Data Security Bay-64

The Data Security Bay-64 is an affordable DES (64-bit) real-time

hardware data encryption/decryption solution for your data

protection.

Features and Benefits

• Equipped with National Institute of Standards and

Technology (NIST) certified DES (64-bit) real-time

encryption/decryption hardware engine

• Capable of maneuvering 1.1 Gbps throughput without

taking extra CPU time and system resources

• Easy-Front-Access and fits into either 3.5" or 5.25" (with

included mounting rack) device bay

• An affordable real-time encryption/decryption solution

encrypts the entire hard drive contents including boot sector

and operating system without performance degradation

• All disk write (encryption) and disk read (decryption)

operations are completely transparent to users

• Two personal security keys included for authentication

• Operating system independent. No driver required!

• Works with various brands of Ultra ATA 133/100/66/33

hard disk drives and achieves data transfer rates up to

100 MB/sec

System Requirements

• Pentium or equivalent PC with one available 3.5" or 5.25"

device bay

• On-board or add-on Ultra ATA (IDE) interface

• Windows 98/98SE/ME/NT4.0/2000/XP

Data Security Bay-64

Quick Installation Guide

04-0285B

Package Contents

• (1) Data Security Bay-64

• (1) 5.25" mounting rack

• (2) Security Keys (identical)

• (1) 40-pin/80-wire Ultra ATA cable

• (1) "Y" split power cable & installation kit

• This quick installation guide

Layout

Figure 1. Layout

Default Jumper Settings

Security Key

Slot Activity

LED

IDE Controller

Connector

Hard Disk Drive

Connector

Power

Connector JP1 JP2

Figure 2. Default Jumper Settings

JP1 JP2

Jumper Setting Configurations

JP1

1-2 Disable

Encrypt/Decrypt

2-3 Enable

Encrypt/Decrypt

(Default)

JP2

1-2 Slave

2-3 Master

(Default)

Figure 3. Jumper Setting Configurations

5.25" Mounting Rack Assembly

Note: Use the Mounting Rack Assembly only when installing into

a 5.25" drive bay.

Figure 4. 5.25" Mounting Rack Assembly

Installation

ThisDataSecurityBay-64onlysupportsonesecuredharddiskdrive.

Do not connect two hard disk drives to this controller.

The hard disk drive connected to this controller is only available if

the Security Key is inserted during boot process. You can remove

this key after Windows has completed booting and still have

complete access to information on this drive. On the other hand,

if the Security Key is NOT inserted during the boot proccess, the

hard disk drive will not be seen by your system.

Note: Static Electricity Discharge may permanently damage your

system. Discharge any static electricity build up in your body by

touching your computer’s case for a few seconds. Avoid any

contact with internal parts and handle cards only by their external

edges.

Configuring the Bay-64

1. Remove the sticker on the buzzer.

Note: The buzzer will make noise if a 1394 device, other than

the Security Key, is connected to the security key slot.

2. Set JP1 (see figure 3) to enable/disable encrypt/decrypt.

3. Set JP2 (see figure 3) to master/slave setting.

Note: Make sure JP2 is set to Master to enable encrypt/

decrypt.

Configuring the Hard Disk Drive

1. Always set the hard disk drive to master whenever you want

to encrypt/decrypt the hard disk drive.

2. Make sure you are starting with a new hard disk drive or

backup all of your data if you want to use an existing hard

disk drive.

Installing the Bay-64

1. Select an available 3.5" or 5.25" device bay for the Bay-64,

remove the cover plate from the selected device bay.

Note: When installing into a 5.25" device bay, mount the

Bay-64 into the 5.25" adapter first and follow the same

instructions. See Figure 4, 5.25" Mounting Rack Assembly.

2. Connect one end of the provided IDE cable to the IDE

Controller Connector (see below) on the Bay-64.

3. With a separate IDE cable (not provided), connect one end of

the cable to the Hard Disk Drive Connector (see below) on

the Bay-64.

4. Slide the Bay-64 into the device bay. Do not secure it at this

time.

5. Connect the IDE Controller Connector IDE cable (from #2

above) to the IDE controller on the motherboard or an add-

on controller.

6. Connect Hard Disk Drive Connector IDE cable (from #3

above) to your hard disk drive.

7. Connect a mini power connector (same type of power

connector used for the floppy drive) to the Power Connector

(see below) on the Bay-64. Use the included "Y" split power

cable if your system doesn't have an available mini power

connector.

Figure 5. Device Connections

8. Verify your device connections, then secure the Bay-64 to the

device bay using the provided installation kit.

IDE Controller

Connector

Hard Disk Drive

Connector

Power

Connector

Mounting

Screw

Figure 6. Mounting the Bay-64

9. Replace the computer cover and attach the power cord.

10. Insert your Security Key into the Security Key Slot and

power up your system.

11. Follow the regular procedures to partition and format the

hard disk drive.

Note: For existing hard disk drive with information, make

sure to back up information on this hard disk drive prior to

partition and format.

Important RMA Notice:

Theharddiskdrivethat'sencrypted/decryptedbyagiven Security

Key will only be recognized by that key. If you need to exchange

this product for any reason, do NOT send the keys in. Your hard

disk drive will only be recognized by the original key(s) that you

used to encrypt/decrypt it with.

Technical Support

QUESTIONS? SIIG’s Online Support has the answers! Simply

visit our web site at www.siig.com and click SUPPORT. Our

online support database is updated daily with new drivers and

solutions. The answers to your problems could be just a few clicks

away.

Return Merchandise Authorization (RMA)

SIIGwarrantstotheoriginal buyer of the product that the hardware

is free of defects in materials and workmanship for a period of one,

two or five years from the date of purchase. If your product fails to

be in good working order during the warranty period, you may

return it to SIIG for repair or replacement at SIIG's option.

To return the product, you need to follow these steps.

Step 1: Contact SIIG's RMA Department

To obtain an RMA number, SIIG's RMA Department can be

reached by phone at (510)413-5333 or fax at (510)657-5962 or email

at[email protected]. In order to issue an RMA number, the product

serial number is required. This number can be found on the side

of the box and on the back of the product.

Step 2: Complete the RMA form

• Fill out your Return Merchandise Authorization (RMA)

form, and include it in the package with the product.

• Properly pack the product for shipping. All software,

cable(s) and other accessories that came with the original

package must be included.

• Clearly write your RMA number on the top of the returned

package and on the accompanying RMA form.

SIIG will refuse to accept any shipping package, and will not

beresponsibleforaproductreturned without an RMAnumber

posted on the outside of the shipping carton.

Step 3: Ship the Product

You are responsible for the cost of shipping back to SIIG at the

following address:

SIIG, Inc. RMA#_______________

6078 Stewart Ave.

Fremont, CA 94538

SIIG will ship the repaired or replaced product via UPS Ground or

US Mail at no cost to you.

UK Warranty & Support Information

The 5 year warranty supplied with this product is offered by SIIG,

Inc. If you should happen to encounter any problems with this

product, please follow the procedures below.

1. If it is within the first year of purchase, please return product

to the outlet you purchased from.

2. If your product is between 2 and 5 years old from date of

purchase, please contact SIIG using the contact details below.

For UK Technical Support

Telephone: +44 (0) 1255 687503

Fax: +44 (0) 1255 687501

Email: [email protected]

Website: http://www.siig.uk.com

PRODUCT NAME MODEL NUMBER

Data Security Bay-64 CN2506

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B

OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR

PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

Data Security Bay-64 is a trademark of SIIG, Inc.

SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered

trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation.

Other names used in publication are for identification only and may be trademarks of their

respective companies.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SIIG Computerhardware Handbücher

SIIG

SIIG 1 FireWire 800 CardBus DV-Ki Bedienungsanleitung

SIIG

SIIG FireWire 800 ExpressCard Bedienungsanleitung

SIIG

SIIG FireWire 800 + Hi-Speed USB Combo Bedienungsanleitung

SIIG

SIIG Parallel Pro Bedienungsanleitung

SIIG

SIIG DP FireWire 800 3-Port PCIe Bedienungsanleitung

SIIG

SIIG 1-Port ECP Bedienungsanleitung

SIIG

SIIG CyberSerial POS 4000RJ Bedienungsanleitung

SIIG

SIIG DP FireWire 800 PCIe Bedienungsanleitung

SIIG

SIIG CyberSerial ExpressCard Bedienungsanleitung

SIIG

SIIG Low Profile USB Adapter Bedienungsanleitung

SIIG

SIIG USB 2.0+1394 DV Kit Bedienungsanleitung

SIIG

SIIG Dual Profile Hi-Speed USB 4-Port PCI Bedienungsanleitung

SIIG

SIIG NN-EC2812-S1 Bedienungsanleitung

SIIG

SIIG Network Device EVTEK-5103 Installationsanleitung

SIIG

SIIG JU-P40311-S1 Bedienungsanleitung

SIIG

SIIG Cyber I/O PCI Bedienungsanleitung

SIIG

SIIG 104-0487A Bedienungsanleitung

SIIG

SIIG NN-EC2822-S1 Bedienungsanleitung

SIIG

SIIG ExpressCard 11-in-1 Reader/Writer Bedienungsanleitung

SIIG

SIIG USB 2.0 5-Port PCI Bedienungsanleitung

SIIG

SIIG Serial ATA PCI RAID Bedienungsanleitung

SIIG

SIIG CyberParallel ExpressCard Bedienungsanleitung

SIIG

SIIG UltraATA 100 Pro Bedienungsanleitung

SIIG

SIIG DP PCI-to-PS/2 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung