SIIG UltraATA 133 PCI Bedienungsanleitung

UltraATA 133 PCI

Quick Installation Guide

04-0233A

Introducing the

UltraATA 133 PCI

The UltraATA 133 PCI is an ultra high-speed dual channel Ultra

ATA/133controllerboardforuseinPentium-classcomputer. With

full support specified in ATA/ATAPI-6, it achieves burst data

transferratesupto133MB/secandsupportsdrivecapacitiesgreater

that 137GB.

Features and Benefits

• Compliant with Ultra ATA/133 specifications and PCI v2.2/

2.1 Plug-n-Play

• Provides two independent Ultra ATA channels (built-in 128-

byte FIFOs per channel) for faster data transfer

• Full ACPI power management support

• Supports Ultra DMA 0, 1, 2, 3, 4, 5, 6 and Multi-word DMA 0,

1, 2

• Breaks the 137GB barrier! Supports hard drives larger than

137GB

• Coexists with on-board IDE controller

• CRC (Cyclical Redundancy Check) error-checking provides

data verification and achieves flawless data tranfer

• Flash BIOS for easy upgrade

• Achieves burst data transfer rates up to 133MB/sec

• Works with various brands of Ultra ATA 133/100/66/33 hard

disk drives and ATAPI devices including CD-ROM, CD-R/

RW, DVD-ROM, and zip drives

System Requirements

• Pentium-class computer with one available PCI slot

• Windows 95B or later

Package Contents

• UltraATA 133 PCI board

• Driver diskette

• 40-pin/80-wire Ultra ATA cable

• This quick installation guide

• One 5-year warranty card

Hardware Installation

General instructions for installing the card are provided below. If

needed, please refer to your computer’s reference manual for more

information.

Caution: Static Electricity Discharge may permanently damage

your system. To avoid possible static electricity discharge during

installation, please follow the guidelines below:

•Dischargeanystaticelectricitybuildupinyourbodybytouching

alargegroundedmetalsurfaceorthecomputer’scase(if

pluggedin), forafewseconds.

•During installation, avoid any contact with internal parts.

Handle cards only by their external edges.

1. Turn OFF the power to your computer and any other con-

nected peripheral devices.

2. Unplug the power cord from the back of the computer.

3. Open your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. To install the card, carefully align the card's bus connector with

the selected PCI slot on the motherboard. Push the board down

firmly, but gently, until it is well seated.

6. Replace the slot bracket's holding screw to secure the card.

7. Close your computer's cover and reconnect the power cord.

Note: Hold the board by its external edges only. Try to avoid

touching the components, connectors or pins.

Device Connection

The UltraATA 133 PCI is a dual channel Ultra ATA/133

controller that supports up to four IDE hard disk drives or ATAPI

devices. If you plan to use the second IDE channel(IDE2), you will

need to purchase another 40-pin/80-wire Ultra ATA ribbon cable.

Inorder toachieve high-speeddata transfer,a 40-pin/80-wireUltra

ATAribboncableisrecommended. Also,donotmixUltraATA/133

hard disk with slower IDE or ATAPI devices on the same channel.

1. Install hard disk drive(s) in chassis.

2. Attach one connector on the long end of the Ultra ATA ribbon

cable to the board's IDE connector and the other connector(s)

to your hard disk drive(s). Make sure pin 1 on the cable

(indicated by the colored stripe) matches pin 1 on the board's

IDE connector and your hard disk drive(s).

3. When two hard disk drives are installed on the same IDE

channel, make sure one drive is set up as Master and the other

as Slave. This rule applies to both IDE channels.

4. The Ultra ATA ribbon cable has two connectors. If you install

only one drive, connect it to the end connector of the cable.

On the other hand, if you install two drives, connect the master

drive to the end connector of the cable and the slave drive in

the middle connector.

Figure 1. Connecting the cable

Software Installation

ThissectionprovidesinformationonhowtoinstalltheUltraATA133

PCI drivers for the following operating systems:

New & Existing Windows 95B

New & Existing Windows 98

New & Existing Windows ME

New & Existing Windows NT 4.0

New & Existing Windows 2000

New & Existing Windows XP

Windows 95B Driver Installation

For New Windows 95B systems

1. Follow Microsoft procedures to install Windows 95B

accordingly.

2. Once Windows 95B is installed, restart Windows in Safe

Modeby hitting the F8 key repeatedly before Windows Logo

boot-up screen.

3. Double click My Computer/Control Panel/System, then click

Device Manager.

4. Remove PCI SCSI Bus controller listed under Other Devices.

5. Restart Windows. Windows will detect new hardware and

prompt for Driver diskette.

6. Insert the Driver diskette, click Next, select Other Locations,

type in A:\Win9x, click OK, then Finish. From the Insert

Disk window, click OK, then type the path A:\Win9x and

click OK.

7. Remove the Driver diskette and click Yes to restart Windows

to complete driver installation.

For Existing Windows 95B Systems

1. Boot up Windows 95B.

2. At the Update Device Driver Wizard, click Next.

3. Insert the Driver diskette, click Other Locations, type in

A:\Win9x, click OK, and then Finish. From the Insert Disk

window, click OK. When the Copying Files dialog box

appears, type in A:\Win9x and click OK.

4. Remove the Driver diskette and restart Windows to complete

driver installation.

Verify Proper Installation for Windows 95B

1. Double click My Computer/Control Panel/System, then click

Device Manager.

2. Double click hdc; IDE dev, an entry, SIIG CN2487 UDMA133

IDE Controller, should be listed.

3. Highlight SIIG CN2487 UDMA133 IDE Controller and click

Properties. A message This device is working properly is

displayed in the dialog box, the driver has been correctly

installed. If any error message is displayed, remove SIIG

CN2487 UDMA133 IDE Controller and restart your system.

Windows 98/98SE Driver Installation

For New Windows 98/98 SE Systems

1. Follow Microsoft procedures to install Windows accordingly.

2. Once Windows has been installed, double click My

Computer/Control Panel/System, then click Device Manager.

3. Double click Other Devices then PCI SCSI Bus Controller.

4. Click Driver tab, then Update Driver.

5. Insert the Driver diskette and click Next.

6. Select Search for a better driver than the one .... and click

Next.

7. Check Specify a location, uncheck the other boxes, type in

A:\Win9x and click Next. Click Next, Next, then Finish.

8. Remove the Driver diskette and click Yes to restart Windows

to complete driver installation.

For Existing Windows 98/98 SE Systems

1. Boot up Windows.

2. At the Add New Hardware Wizard, click Next.

3. Select Search for the best driver for your device option and

then click Next.

4. Insert the Driver diskette, check Specify a location, uncheck

the other boxes, type in A:\Win9x, and click Next.

5. Click Next,Next, and then Finish respectively.

6. Remove the Driver diskette and restart Windows to complete

driver installation.

Windows ME Driver Installation

For New Windows ME Systems

1. Follow Microsoft procedures to install Windows ME

accordingly.

2. Once Windows has been installed, right-click My Computer,

then click Properties. Click Device Manager tab.

3. Double click Other Devices then PCI SCSI Bus Controller.

4. Click Driver tab, then Update Driver.

5. Insert the Driver diskette, check Specify the location of the

driver (advanced) and click Next.

6. Select Search for the better driver option, check Specify a

location, uncheck Removable Media, type in A:\WinMe, and

click Next.

7. Click Next and Finish.

8. Remove the Driver diskette and click Yes to restart Windows

to complete driver installation.

For Existing Windows ME Systems

1. Boot up Windows ME.

2. At the Add New Hardware Wizard, check Specify the

location of the device (advanced), and click Next.

3. Insert the Driver diskette, check Specify a location, uncheck

the other boxes, type in A:\WinMe, and click Next.

4. Click Next and Finish.

5. Remove the Driver diskette and restart Windows to complete

driver installation.

Verify Proper Installation for Windows 98/98SE/ME

1. Right-click My Computer, then click Properties. Click Device

Manager tab.

2. Double click Hard Disk Controllers, an entry, SIIG CN2487

UDMA133 IDE Controller should be listed.

3. Highlight SIIG CN2487 UDMA133 IDE Controller and click

Properties. A message This device is working properly is

displayed in the dialog box, the driver has been correctly

installed. If any error message is displayed, remove SIIG

CN2487 UDMA133 IDE Controller and restart your system.

Windows NT 4.0 Driver Installation

For New Windows NT 4.0 System

1. Follow Microsoft procedures to install Windows NT 4.0

accordingly.

2. At the Windows Set-up screen, press F6 to specify and add

the driver.

3. Press S, select Other, then press Enter.

4. Insert the Driver diskette and press Enter.

5. Select SIIG CN2487 UDMA133 IDE NT miniport Driver and

press Enter.

6. Press Enter to continue and follow on-screen instructions to

complete Windows NT 4.0 installation.

For Existing Windows NT 4.0 System

1. After installing the board, boot up Windows NT. Double click

My Computer/Control Panel/SCSI Adapters, then click the

Driverstab.

2. Click Add… then Have Disk....

3. Insert the Driver diskette into the floppy drive and type in

A:\Winnt, then click OK.

4. Highlight SIIG CN2487 UDMA133 IDE Adapter and click

OK.

5. Remove the Driver diskette and click Yes to restart Windows.

Verify Proper Installation for Windows NT 4.0

1. Double click My Computer/Control Panel/SCSI Adapters.

2. Highlight SIIG CN2487 UDMA133 IDE Adapter from SCSI

Adapters listing and click Properties. A message This device is

working properly is displayed in the dialog box, the driver has

been correctly installed.

Windows 2000 Driver Installation

For New Windows 2000 Systems

1. Follow Microsoft procedures to install Windows 2000

accordingly.

2. At the Windows Set-up screen, press F6 to specify and add

the driver.

3. Insert the Driver diskette. Press S, then press Enter.

4. Select SIIG CN2487 UDMA133 IDE Win2000 Miniport

Driverand press Enter.

5. Press Enter to continue and follow on-screen instructions to

complete installation.

For Existing Windows 2000 Systems

1. Boot up Windows 2000.

2. At the Found New Hardware Wizard, click Next.

3. Select Search for a suitable driver for my device

(recommended) and click Next.

4. Insert the Driver diskette into the floppy drive, check Specify

a location, uncheck the other boxes, click Next, type in

A:\Win2000. Click OK and then Next to continue.

5. If the Digital Signature Not Found message appears, click

Yes.

Note If prompted for Windows 2000 CD-ROM, insert the CD

and clickOK. Type inD:\I386, clickOK andFinish. (assuming

D: is your CD-ROM drive)

6. Click Finish, remove the Driver diskette and click Yes to

restart Windows to complete driver installation.

Windows XP Driver Installation

For New Windows XP Systems

1. Follow Microsoft procedures to install Windows XP

accordingly.

2. At the Windows Set-up screen, press F6 in order to specify

and add the driver.

3. Insert the Driver diskette. Press Sthen press Enter.

4. Select SIIG CN2487 UDMA133 IDE WinXP Miniport Driver

and press Enter.

5. Press Enter to continue and follow on-screen instructions to

complete Windows XP installation.

Note: When the Software Installation warning pops up, click

Yes. And when the Hardware Installation warning pops up,

click Yes again.

For Existing Windows XP Systems

1. Boot up Windows XP.

2. At the Found New Hardware Wizard, check Install from a

list or specific location(advanced), then click Next.

3. Insert the Driver diskette. Check Include this location in the

search, uncheck the other box, type in A:\winXP, and click

Next.

4. When a warning message pops up, click Continue Anyway,

then click Finish.

5. Remove the Driver diskette and click Yes to restart Windows.

Verify Proper Installation for Windows 2000/XP

1. Double click My Computer/Control Panel/System.

2. Click Hardware then click Device Manager.

3. Double click SCSI and RAID Controllers, then double click

SIIG CN2487 UDMA133 IDE Adapter to display driver

properties.

4. A message This device is working properly is displayed in the

dialog box, the driver has been correctly installed.

Bios Configuration

The UltraATA 133 PCI BIOS will appear everytime your system

starts up. If the bios doesn't show, please try your controller in

another PCI slot. During this (Post) process, the bios will show up

and indicate the devices attached to it.

Empty page

Andere Handbücher für UltraATA 133 PCI

Inhaltsverzeichnis

Andere SIIG Controller Handbücher

SIIG

SIIG eSATA II PCIe Pro Bedienungsanleitung

SIIG

SIIG FireWire 800 M-64 Bedienungsanleitung

SIIG

SIIG UltraATA 133 PCI Bedienungsanleitung

SIIG

SIIG CE-S00012-S2 Bedienungsanleitung

SIIG

SIIG USB SoundWave 7.1 Pro Bedienungsanleitung

SIIG

SIIG Smart Controller for HDMI over IP Series Bedienungsanleitung

SIIG

SIIG CE-E01012-S1 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch