SIIG 13" Bedienungsanleitung

Triple Monitor Desk Stand - 13" to 24"

Installation Instructions

04-0884A

Unpacking

• Carefully remove the contents and lay out on cardboard or other protective surface

• Check package contents against the parts list to ensure that all components were received

undamaged. Do not use damaged or defective parts

• Carefully read all instructions before attempting installation

Safety Information

• Use proper safety equipment during installation

• If you don't understand the installation instructions, please consult an installation

specialist

• This mount contains small parts which can act as a choking hazard if swallowed

• Do not use this product for any purpose or in any configuration not explicitly specified

in these instructions

Tools Required

• Phillips screwdriver

• 3/8" drill bit (for Grommet installation)

• Electric drill (for Grommet installation)

Parts List

a - (1x) 48mm

TubeSupport

c1 - (2x) Side

Vesa Plate

e - (1x) Arm

ConnectPlate

i - (2x) Arm Plastic

Cover

j - (3x) M6x29

Bolt

k - (1x) Decorative

Cover

l - (1x) Grommet

Plate

m - (1x) Grommet

Bolt

n - (1x) Wing

Nut

o - (3x) Allen

Key

p - (24x) M4

Washer

b - (1x) Weighted

Base

d - (2x) Curved

Arm

f - (1x) Arm

Clamp

g - (4x) M6x25

Bolt

h - (4x) M6

Washer

r - (12x) M4x30

Bolt

s - (12x) M4

Spacer

t - (2x) M8x10

Bolt

u - (2x) Wire

clip

q - (12x) M4x12

Bolt

c2 - (1x) Middle VESA

Plate

v - (2x) M4x16

Bolt with Washer

Installation

The Monitor Desk Stand can be free standing (Weighted Base Installation) or permanently

attached to the desktop (Grommet Hole Installation).

Step 1 - Mounting the Tube Support

1a) Weighted Base Installation

For free standing, simply mount the 48mm Tube Support (a) to the Weighted Base (b) using

M6x29 Bolts (j) then slide the Decorative Cover (k) onto the tube support as show in Figure

1a. Then continue to Step 2.

Figure 1a

1b) Grommet Hole Installation

This installation requires you to either drill a 3/8" (10mm) diameter hole through the desktop

or use an existing grommet hole. If the existing grommet hole comes with a plastic protector,

remove it to ensure a flat surface before installing.

Mount the 48mm Tube Support (a) using Grommet Bolt (m), Grommet Plate (l) and secure

with Wing Nut (n), then slide the Decorative Cover (k) onto the tube support as shown in

Figure 1b. Then continue to Step 2.

Figure 1b

Figure 2a

Step 2 - Assemble Curved Arms and Install it onto the Tube Support

1. Assemble theCurved Arms (d), Arm Connector Plate (e), Arm Clamp (f)and fasten with

M6x25 Bolts (g) and M6 Washers (h) using Allen Key (o) as shown in Figure 2a.

Important: Position the Arm Connector Plate (e) so that the screw holes are oriented to the

bottom.

Figure 2b

2. Mount the Arm Assembly to the tube support, fasten it using M8x10 Bolts (t) with Allen

Key (o) and insert the Wire Clips (u) as shown in Figure 2b. Then continue to Step 3.

Figure 3a

Step 3 - Mounting the VESA Plate to the Monitor

3a) For Flat Back Monitors

MounttheVESA Plates (c1 & c2) using M4x12 Bolts(q) andM4 Washers (p) asshowninFigure

3a. Then continue to Step 4.

3b) For Curved Back Monitors

Mount the VESA Plates (c1 & c2) using M4x30 Bolts(r) and M4 Washers (p) as shown in Figure

3b. Then continue to Step 4.

Figure 3b

Step 4 - Mounting the Monitors and Adjusting the Tilt Angle

1. Attach the Middle VESA Plate (c2) with Monitor Assembly and secure it using M4x16

Bolt with Washers (v), then slide the Side VESA Plate (c1) with Monitor Assemblies onto

the Arm Assembly and secure by rotating the Plastic Knob. Install the Arm Plastic

Covers (i) onto the Arm Assembly as shown in Figure 4a.

Caution: For Weighted Base Installation, we suggest you have a helper hold the desk

stand upright while attaching your monitors to prevent damage to the monitor or desk

stand and ensure your personal safety.

Figure 4a

2. Adjust the monitor's tilt angle, use the Allen Key (o) to loosen the Grub Screw, then

tighten the Grub Screw to fix the tilt angle as shown in Figure 4b.

Figure 4b

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SIIG Rack & Stand Handbücher

SIIG

SIIG Full-Motion Easy Access Single Monitor Desk... Bedienungsanleitung

SIIG

SIIG CE-MT2Q12-S1 Bedienungsanleitung

SIIG

SIIG CE-MT2912-S1 Bedienungsanleitung

SIIG

SIIG CE-MT2P12-S1 Bedienungsanleitung

SIIG

SIIG CE-MT2X11-S1 Bedienungsanleitung

SIIG

SIIG CE-MT1X12-S1 Bedienungsanleitung

SIIG

SIIG Security Countertop Kiosk & POS Stand for... Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung