Siko MA10/4 Bedienungsanleitung

User manual

Electronic display

MA10/4 Software S

MA10/4-S Date: 21.02.2019 Page 2 of 28 Art.No. 87181 Mod. status 50/19

Table of contents

1General Information .................................................................................................................... 3

1.1 Documentation.......................................................................................................................... 3

2Key functions............................................................................................................................... 3

2.1 Operating modes....................................................................................................................... 3

3Display description ..................................................................................................................... 4

3.1 Incremental and SSI versions................................................................................................... 4

3.2 Rototional speed version........................................................................................................... 4

3.3 Number of pieces version ......................................................................................................... 4

4Programming mode .................................................................................................................... 5

5Parameter description ................................................................................................................ 6

5.1 Incremental version................................................................................................................... 6

5.2 SSI version................................................................................................................................ 8

5.3 Speed version ......................................................................................................................... 10

5.4 Number of pieces version ....................................................................................................... 11

6Input mode................................................................................................................................. 13

6.1 Reset function ......................................................................................................................... 13

6.2 Incremental measurement ...................................................................................................... 13

6.3 Direct alteration of reference/offset value or calibration/offset value...................................... 13

6.4 Direct input of limiting value.................................................................................................... 14

7Referencing / Calibration.......................................................................................................... 14

7.1 Manual referencing / calibration.............................................................................................. 14

7.2 Automatic referencing ............................................................................................................. 15

8Serial Interface........................................................................................................................... 16

8.1 Standard protocol.................................................................................................................... 16

8.2 SIKONETZ3 Protocol description ........................................................................................... 19

9Application examples for speed.............................................................................................. 22

9.1 How to display revolutions/minute (rpm)................................................................................. 22

9.2 How to display Hz (s-1)............................................................................................................ 22

9.3 Some practise application examples ...................................................................................... 22

9.4 Cycle times recom. for certain pulse counts........................................................................... 24

10 MA10/4 in combination with MSK magnetic sensor.............................................................. 25

11 Trouble shooting....................................................................................................................... 26

12 Parameter list............................................................................................................................. 26

12.1 Incremental version................................................................................................................. 26

12.2 SSI version.............................................................................................................................. 27

12.3 Speed...................................................................................................................................... 28

12.4 Number of pieces version ....................................................................................................... 28

MA10/4-S Date: 21.02.2019 Page 3 of 28 Art.No. 87181 Mod. status 50/19

1 General Information

1.1 Documentation

The following documents describe this product:

The product data sheet describes the technical data, the dimensions, the pin assignments,

the accessories and the order key.

The mounting instructions describe the mechanical and electrical installation including all

safety-relevant requirements and the associated technical specifications.

The user manual of commissioning the electronic display.

These documents can also be downloaded at http://www.siko-global.com/en-de/service-

downloads.

2 Key functions

The display is operated and programmed by means of the four keys of the membrane keyboard.

Depending on the operating mode the keys may have additional functions (see 'Programming

mode' and 'Input mode'). The keys are actuated individually or combined (each two of them)

and time-dependent.

Fig. 1: Key functions

2.1 Operating modes

There are two operating modes:

1. Programming mode: Single set-up of the display for the intended application.

2. Input mode: Functions required during normal application (not speed).

1) Programming

2) Select 'value'

3) Select 'digit'

4) Store value

Programming

2) Select

'value'

3) Select

'digit'

4) Store

value

MA10/4-S Date: 21.02.2019 Page 4 of 28 Art.No. 87181 Mod. status 50/19

3 Display description

The MA10/4 has a backlighted 12-digit LC display. The display as well as the meaning of the

individual symbols is explained in the tables below.

3.1 Incremental and SSI versions

Digit

Position value

Digit

Symbol

Description

Incremental measure is active.

Upper limiting value exceeded (only for output circuit option). If

incremental measure as well as exceeding of the limiting value is active,

this will be displayed alternately.

Lower limiting value exceeded (only for output circuit option). If

incremental measure as well as exceeding of the limiting value is active,

this will be displayed alternately.

2-9

Measured value; negative values are displayed by "-" on position 2.

11-12

Unit of measure (programmable)

3.2 Rototional speed version

Digit

Position value

Digit

Symbol

Description

Upper limiting value exceeded (only for output circuit option). If

incremental measure as well as exceeding of the limiting value is active,

this will be displayed alternately.

Lower limiting value exceeded (only for output circuit option). If

incremental measure as well as exceeding of the limiting value is active,

this will be displayed alternately.

2-6

Measured value

8-12

Unit of measure (programmable)

3.3 Number of pieces version

Digit

Position value

Digit

Symbol

Description

Incremental measure is active.

Upper limiting value exceeded (only for output circuit option). If

MA10/4-S Date: 21.02.2019 Page 5 of 28 Art.No. 87181 Mod. status 50/19

Digit

Symbol

Description

incremental measure as well as exceeding of the limiting value is active,

this will be displayed alternately.

Lower limiting value exceeded (only for output circuit option). If

incremental measure as well as exceeding of the limiting value is active,

this will be displayed alternately.

2-8

Measured value; negative values are displayed by "-" on position 2.

10-12

Unit of measure (programmable)

4 Programming mode

The display is delivered ex factory with default settings. Normally programming is only

necessary at initial installation. Parameters can be modified and checked at any time. They are

stored in a non-volatile memory. For designation, function and selectable values see chapter 5.

To change and control parameters

For parameter modification enter into programming mode.

To enter into the programming mode

Press key for at least 5 s (pre-programmed) or for the period programmed under P-KEY

delay.

To leave programming mode

Automatically, if no key has been pressed during approx. 30 s, or press key until the end of

the parameter list is reached.

To scroll parameter information

Use key .

Input of numerical values

For numerical values the smallest decade flashes first. The numerical value of the flashing digit

can be updated by pressing the key. The next digit can be accessed by pressing the key.

Changing given selection

By means of the key.

Accepting/ saving the changed value

By pressing the key, the message "speichern..." will be displayed for a short while.

MA10/4-S Date: 21.02.2019 Page 6 of 28 Art.No. 87181 Mod. status 50/19

5 Parameter description

At chapter 12 you will find a detailed parameter list showing all programmable parameters and

offering space for customer-specific programming values.

(in English, parameter LANGUAGE = "eng")

After entering the programming mode (see chapter 4) the parameters described below can be

configured. Depending on the settings selected, only the menu items that are relevant for the

application will be displayed.

5.1 Incremental version

Display

Value range

Description

LANGUAGE:

ger or deu

(German)

eng (English)

Language

To choose the language in which the menu items are to

be displayed.

Attention! The term "SPRACHE" will be displayed first in

German.

DEC:

0., 0.0, 0.00,

0.000, 0.0000

Positions after the comma

DPR:

0 ... 59999

Display after 1 revolution

Value by which the display increases/decreases after 1

revolution of the encoder. If DPR: = 0, quadruple

evaluation of the encoder signal will take place

automatically.

DIVISOR:

1, 10, 100,

1000

Display divisor

Divisor by which the display accuracy is reduced

compared to the measuring accuracy. Example: Due to an

integer value ratio, the measuring resolution is

programmed to 1/1000 mm. The display, however, needs

a resolution of 1/10 mm only. -> The display divisor is

programmed to '100'.

INCR:

0 ... 59999

Encoder pulses per revolution

If INCR: = 0, quadruple evaluation of the encoder signal

will take place automatically.

DIRECTION:

i, e

Counting direction

'i' clockwise increasing values

'e' anti-clockwise increasing values

INDEX:

I-lang, 0-lang, I-

kurz, 0-kurz

Input of logic and length of the encoder's reference signal

The encoder reference signal is output only once per

revolution.

'lang' index signal is wider than one increment; index is

linked with A and B signals.

'kurz' index signal is exactly as wide as one increment

'0' index signal with positive logic

'I' index signal with negative logic

MA10/4-S Date: 21.02.2019 Page 7 of 28 Art.No. 87181 Mod. status 50/19

Display

Value range

Description

TRS:

n.open,

n.closed, hand

Reference switch

Type of reference value transmitter; can either be a

mechanical contact or a proximity switch.

'n.open' closing contact, which is normally open

'n.closed' opening contact, which is normally closed

'hand' Referencing arbitrarily via callipers independent of

A and B, index signal). The input is current-sinking and

edge-triggered.

REF:

-999999 ...

+999999

Reference point for the measuring system

Absolute datum point of the measuring system. This value

is set after system reference accord. to chapter 7.

OFF:

-999999 ...

+999999

Offset (displacement)

An be any value; used to influence the value displayed, e.

g. tool correction value.

RESET:

off, on, del.1s,

del.3s

Reset via keyboard enable

'off' reset function off

'on' reset function enabled

'del.1s' reset function enabled (press key for at least

1 sec.)

'del.3s' reset function enagled (press key for at least

3 sec.)

ABS/REL:

off, on

Incremental measurement enable

To switch from absolute measurement and zero-zetting to

relative measurement.

'off' function off

'on' function on

RE/OF.EN:

off, on

Reference/ offset value input enable

'off' reference/offset value correction off

'on' reference/offset value correction enabled

STO:

off, on

Actual value store

When switched off, the last displayed value is stored in a

non-volatile memory.

'off' Actual value memory off: when switched on, the

display must be calibrated (zeroed) (Display value is

flashing).

'on' Actual value memory on: when switched on, the last

measured value is displayed.

P-KEY:

3s, 5s, 10s,

20s, 30s

Programming keys delay

Delay of key when switching from input to

programming mode.

BAUD:

2400, 4800,

9600, 19200,

SIKON.3,

SCHALT

Interface's baud rate

'SCHALT' must be programmed for switching outputs,

'SIKON.3' for SIKONETZ3.

ADR:

1 ... 31

Adress setting for SIKONETZ3

Menu item will be displayed only if 'SIKON.3' is

programmed for 'BAUD:'.

UPL:

-999999 ...

+999999

For switching output: Input of the upper switching point

Menu item will be displayed only if 'SCHALT' is

programmed for 'BAUD:'.

LOL:

-999999 ...

+999999

For switching output: Input of the lower switching point

Menu item will be displayed only if 'SCHALT' is

programmed for 'BAUD:'.

MA10/4-S Date: 21.02.2019 Page 8 of 28 Art.No. 87181 Mod. status 50/19

Display

Value range

Description

LIMIT.EN:

off, on

Enabling of modification of the limiting value

Menu item will be displayed only if 'SCHALT' is

programmed for 'BAUD:'. Possibility of input/modification

of the upper and lower limiting values in the input mode.

'off' Modification of limiting values disabled in input mode.

'on' Modification of limiting values enabled in input mode.

UNITS:

--, mm, cm, m,

km, in (inch), °

Unit of measure

Choice of the measurement unit to be displayed on

positions 11, 12 (see chapter 3Display description).

DIS.ANGLE:

-5 ... +4

Display angle

Here, the contrast of the LC display can be set.

CODE:

00000

Code input: for service only

CONTROL:

off, on

Code input: for service only

5.2 SSI version

Display

Value range

Description

LANGUAGE:

ger or deu

(German)

eng (English)

Language

To choose the language in which the menu items are to

be displayed.

Attention! The term "SPRACHE" will be displayed first in

German.

E-TYP:

multi, single,

linear

Encoder type

Determines the encoder type connected

'multi' multi-turn encoder

'single' single-turn encoder

'linear' linear measuring system

FORMAT:

no, Tree

Data format

Menu item will be displayed only if "multi" is programmed

for 'E-TYP:'

'no' Encoder data leftjustified (MSB first)

'tree' pine-tree (12 multiturn + 13 singleturn bits data

format)

S-BITS:

5 ... 19

Input of single-turn bits for multi-turn encoder

Menu item will be displayed only if "multi" is programmed

for 'E-TYP:'.

ENCOD.BIT:

5 ... 25

Input of the total encoder bit number

DEC:

0., 0.0, 0.00,

0.000, 0.0000

Positions after the comma

DPR:

0 ... 59999

Display after 1 revolution

Menu item will be displayed only if "multi" is programmed

for 'E-TYP:' Value by which the display

increases/decreases after 1 revolution of the encoder. The

maximum possible encoder resolution is displayed if DPR:

= 0. For 10 bit single-turn: 0 ... 1023

MA10/4-S Date: 21.02.2019 Page 9 of 28 Art.No. 87181 Mod. status 50/19

Display

Value range

Description

DIVISOR:

1, 10, 100,

1000

Display divisor

Menu item will be displayed only if 'single' or 'multi' is

programmed for 'E-TYP:' Divisor by which the display

accuracy is reduced compared to the measuring accuracy.

Example: Due to an integer value ratio, the measuring

resolution is programmed to 1/1000 mm. The display,

however, needs a resolution of 1/10 mm only. -> The

display divisor is programmed to '100'.

FAC:

00.0001 ...

99.9999

Calculating faktor

Freely selectable value, which influences the display.

Menu item will be displayed only if "linear" is programmed

for 'E-TYP:'.

DIRECTION:

i, e

Counting direction

'i' clockwise increasing values

'e' anti-clockwise increasing values

DIRECT:

up (upwards)

down

(downwards)

Counting direction

Menu item will be displayed only if 'linear' is programmed

for 'E-TYP:'.

CAL:

-999999 ...

+999999

Calibration value for the measuring system

Absolute datum point of the measuring system. This value

is set after system calibrated accord. to chapter 7.

OFF:

-999999 ...

+999999

Offset (displacement)

Can be any value; used to influence the value displayed,

e. g. tool correction value.

RESET:

off, on, del.1s,

del.3s

Reset via keyboard enable

'off' reset function off

'on' reset function enabled

'del.1s' reset function enabled (press key for at least

1 sec.)

'del.3s' reset function enagled (press key for at least

3 sec.)

ABS/REL:

off, on

Incremental measurement enable

To switch from absolute measurement and zero-zetting to

relative measurement.

'off' function off

'on' function on

CA/OF.EN:

off, on

Calibration/offset value input enable

'off' calibration/offset value correction off

'on' calibration/offset value correction enabled

OUTPUT:

gray, bin

Output code

'gray' Encoder's data in Gray code

'bin' Encoder's data in binary code

TIMEOUT:

off, on

Time-out function

'off' Cable break recognition off

'on' Cable break recognition off

P-KEY:

3s, 5s, 10s,

20s, 30s

Programming keys delay

Delay of key when switching from input to

programming mode.

BAUD:

2400, 4800,

9600, 19200,

SIKON.3,

SCHALT

Interface's baud rate

'SCHALT' must be programmed for switching outputs,

'SIKON.3' for SIKONETZ3.

MA10/4-S Date: 21.02.2019 Page 10 of 28 Art.No. 87181 Mod. status 50/19

Display

Value range

Description

ADR:

1 ... 31

Address setting for SIKONETZ3

Menu item will be displayed only if 'SIKON.3' is

programmed for 'BAUD:'.

UPL:

-999999 ...

+999999

For switching output: Input of the upper switching point

Menu item will be displayed only if 'SCHALT' is

programmed for 'BAUD:'.

LOL:

-999999 ...

+999999

For switching output: Input of the lower switching point

Menu item will be displayed only if 'SCHALT' is

programmed for 'BAUD:'.

LIMIT.EN:

off, on

Enabling of modification of the limiting value

Menu item will be displayed only if 'SCHALT' is

programmed for 'BAUD:'. Possibility of input/ modification

of the upper and lower limiting values in the input mode.

'off' Modification of limiting values disabled in input mode.

'on' Modification of limiting values enabled in input mode.

UNITS:

--, mm, cm, m,

km, in (inch), °

Unit of measure

Choice of the measurement unit to be displayed on

positions 11, 12 (see chapter 3Display description).

DIS.ANGLE:

-5 ... +4

Display angle

Here, the contrast of the LC display can be set.

SET:

Encoder zeroing

Zeroing of the encoder (+ offset + calibration value) in

programming mode via key.

GDAT:

Position value of the encoder

Display of the actual encoder position.

CODE:

00000

Code input: for special functions

CONTROL:

off, on

Code input: for special functions

5.3 Speed version

(see chapter 9for programming examples)

Display

Value range

Description

LANGUAGE:

ger or deu

(German)

eng (English)

Language

To choose the language in which the menu items are to

be displayed.

Attention! The term "SPRACHE" will be displayed first in

German.

INCR:

0 ... 59999

Encoder pulses per revolution

DEC:

0., 0.0, 0.00,

0.000, 0.0000

Positions after the comma

FAC:

00.0001 ...

99.9999

Calculating faktor

Freely selectable value, which influences the display.

CYCLUS:

0.1s, 0.5s, 1s,

1.5s, 2s, 3s, 5s,

10s

Cycle time

The display is refreshed after the programmed cycle time.

If short cycle times have been programmed

(recommended for high speed applications and high pulse

counts), modifications are quickly displayed. Increase

cycle time if display is irregular.

Andere Handbücher für MA10/4

Inhaltsverzeichnis

Andere Siko Monitor Handbücher

Siko

Siko MA47 Bedienungsanleitung

Siko

Siko MA100/2 Bedienungsanleitung

Siko

Siko MA508/1 Bedienungsanleitung

Siko

Siko MA501-S Bedienungsanleitung

Siko

Siko MA503/1 Bedienungsanleitung

Siko

Siko MA05 Bedienungsanleitung

Siko

Siko MA523/1 Bedienungsanleitung

Siko

Siko MA100/1 SA01 Bedienungsanleitung

Siko

Siko MA55 Bedienungsanleitung

Siko

Siko AP10T Bedienungsanleitung

Siko

Siko MA100/1 Bedienungsanleitung

Siko

Siko MA504/1 Software S Bedienungsanleitung

Siko

Siko MA100/2 Bedienungsanleitung

Siko

Siko MA07/1 Bedienungsanleitung

Siko

Siko MA10/3 Bedienungsanleitung

Siko

Siko MA55 Bedienungsanleitung

Siko

Siko MA508 Bedienungsanleitung

Siko

Siko MA100/2 Bedienungsanleitung

Siko

Siko MA48 Bedienungsanleitung

Siko

Siko MA508 Bedienungsanleitung

Siko

Siko MA03/1 Bedienungsanleitung

Siko

Siko MA55 Bedienungsanleitung

Siko

Siko MA50 Bedienungsanleitung

Siko

Siko MA07/1 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung