Silicon Laboratories C8051F93 Series Bedienungsanleitung

C8051F93x/92x

C8051F930 DEVELOPMENT KIT USER’SGUIDE

1. Relevant Devices

The C8051F930 Development Kit is intended as a development platform for the microcontrollers in the

C8051F93x-C8051F92x MCU family.

Notes:

1. The target board included in this kit is provided with a pre-soldered C8051F930 MCU (LQFP32 package).

2. Code developed on the C8051F930 can be easily ported to the other members of this MCU family.

3. Refer to the C8051F93x-C8051F92x data sheet for the differences between the members of this MCU

family.

2. Kit Contents

The C8051F930 Development Kit contains the following items:

C8051F930 Target Board

C8051Fxxx Development Kit Quick-Start Guide

AC to DC Power Adapter

USB Debug Adapter (USB to Debug Interface)

2 USB Cables

2 AAA Batteries

CD-ROM

Figure 1. C8051F930 Target Board

C8051F93x/92x

2 Rev 0.7

3. Hardware Setup Using a USB Debug Adapter

The target board is connected to a PC running the Silicon Laboratories IDE via the USB Debug Adapter as shown

in Figure 2.

1. Connect the USB Debug Adapter to the DEBUG connector on the target board with the 10-pin ribbon

cable.

2. Connect one end of the USB cable to the USB connector on the USB Debug Adapter.

3. Verify that a shorting block is installed on J17 and that SW5 is in the ON position.

4. Connect the other end of the USB cable to a USB Port on the PC.

5. Connect the ac/dc power adapter to power jack P1 on the target board (Optional).

Notes:

Use the Reset button in the IDE to reset the target when connected using a USB Debug Adapter.

Remove power from the target board and the USB Debug Adapter before connecting or disconnecting the

ribbon cable from the target board. Connecting or disconnecting the cable when the devices have power

can damage the device and/or the USB Debug Adapter.

Figure 2. Hardware Setup Using a USB Debug Adapter

USB

Cable

AC/DC

Adapter

Target Board

P0.2 P0.3

2103

DEBUG

USB POWER

RESET

P1.6

P1.5

POWER OFF BEFORE

SW4

SWITCHING MODE

2 CELL 1 CELL

J17

IMEASURE

SILICON LABS

www.silabs.com

J6 VDD/DC+

J7 J13

F930

J14

J11

J10

VBAT

WALL_PWR

AAA_BAT

COIN_CELL

TOUCH SENSE SWITCH

P2.0 TOUCH SENSE SWITCH

P2.1

J15

J16

R15

J12J8

+3VD

+1VD

VBAT

SW5

OFF

Silicon Laboratories

USB DEBUG ADAPTER

Run

Stop Power

USB Debug

Adapter

C8051F93x/92x

Rev 0.7 3

4. Software Setup

Simplicity Studio greatly reduces development time and complexity with Silicon Labs EFM32 and 8051 MCU

products by providing a high-powered IDE, tools for hardware configuration, and links to helpful resources, all in

one place.

Once Simplicity Studio is installed, the application itself can be used to install additional software and

documentation components to aid in the development and evaluation process.

Figure 3. Simplicity Studio

The following Simplicity Studio components are required for the C8051F930 Development Kit:

8051 Products Part Support

Simplicity Developer Platform

Download and install Simplicity Studio from www.silabs.com/8bit-software or www.silabs.com/simplicity-studio.

Once installed, run Simplicity Studio by selecting StartSilicon LabsSimplicity StudioSimplicity Studio

from the start menu or clicking the Simplicity Studio shortcut on the desktop. Follow the instructions to install the

software and click Simplicity IDE to launch the IDE.

The first time the project creation wizard runs, the Setup Environment wizard will guide the user through the

process of configuring the build tools and SDK selection.

In the Part Selection step of the wizard, select from the list of installed parts only the parts to use during

development. Choosing parts and families in this step affects the displayed or filtered parts in the later device

selection menus. Choose the C8051F93x family by checking the C8051F93x/92x check box. Modify the part

selection at any time by accessing the Part Management dialog from the WindowPreferencesSimplicity

StudioPart Management menu item.

Simplicity Studio can detect if certain toolchains are not activated. If the Licensing Helper is displayed after

completing the Setup Environment wizard, follow the instructions to activate the toolchain.

C8051F93x/92x

4 Rev 0.7

4.1. Running Blinky

Each project has its own source files, target configuration, SDK configuration, and build configurations such as the

Debug and Release build configurations. The IDE can be used to manage multiple projects in a collection called a

workspace. Workspace settings are applied globally to all projects within the workspace. This can include settings

such as key bindings, window preferences, and code style and formatting options. Project actions, such as build

and debug are context sensitive. For example, the user must select a project in the Project Explorer view in order

to build that project.

To create a project based on the Blinky example:

1. Click the Software Examples tile from the Simplicity Studio home screen.

2. In the Kit drop-down, select C8051F930 Development Kit, in the Part drop-down, select C8051F930, and

in the SDK drop-down, select the desired SDK. Click Next.

3. Select Example and click Next.

4. Under C8051F930 Development Kit in the Blinky folder, select F93x-92x Blinky and click Finish.

5. Click on the project in the Project Explorer and click Build, the hammer icon in the top bar. Alternatively,

go to ProjectBuild Project.

6. Click Debug to download the project to the hardware and start a debug session.

7. Press the Resume button to start the code running. The LED should blink.

8. Press the Suspend button to stop the code.

9. Press the Reset the device button to reset the target MCU.

10. Press the Disconnect button to return to the development perspective.

4.2. Simplicity Studio Help

Simplicity Studio includes detailed help information and device documentation within the tool. The help contains

descriptions for each dialog window. To view the documentation for a dialog, click the question mark icon in the

window:

This will open a pane specific to the dialog with additional details.

The documentation within the tool can also be viewed by going to HelpHelp Contents or HelpSearch.

C8051F93x/92x

Rev 0.7 5

4.3. Simplicity Configurator

The Simplicity Configurator is a configuration and code generation tool. This utility helps accelerate development

by automatically generating initialization source code to configure and enable the on-chip resources needed by

most design projects. In just a few steps, the wizard creates complete startup code for a specific Silicon Labs MCU.

To create a new Simplicity Configurator project:

1. Click the Create new project link from the welcome screen or go to FileNewSilicon Labs MCU

Project.

2. In the Kit drop-down, select C8051F930 Development Kit or None, in the Part drop-down, select

C8051F930, and in the SDK drop-down, select the desired SDK. Click Next.

3. Select Simplicity Configurator Program and click Next.

4. Fill in the Project name and select the desired device. The C8051F930-G-GQ-LQFP device is on the

C8051F930 Target Board. Click Finish.

The Simplicity Configurator project displays properties for each peripheral. To configure a peripheral, click on the

DefaultMode Peripherals tab at the bottom and click on a peripheral. Checking the box for a peripheral will add it

to code generation. Once a peripheral is selected, configure the registers using the Properties view. Select a new

value for a property with either an input box or a drop-down menu and press Enter to set it.

Figure 4. Simplicity Configurator – Configuring Peripheral Properties

C8051F93x/92x

6 Rev 0.7

To configure pins, click on the DefaultMode Port I/O tab at the bottom of main window. Clicking on a pin brings up

a property window for the pin. Clicking anywhere else in the main window opens a property window for the

crossbar. Select multiple pins with Ctrl + left click or mouse dragging over the desired set of pins. The package

diagram displays the configured peripherals on the pins, including non-crossbar signals (i.e. ADC inputs).

Code generation updates every time the configuration project saves. After configuring the device, add any non-

initialization code, build, and debug the same as with any other project.

More information on Simplicity Configurator can be found in AN0823: Simplicity Configurator User’s Guide and

AN0821: Simplicity Studio C8051F85x Walkthrough. Application notes can be found on

www.silabs.com/8bit-appnotes.

Figure 5. Simplicity Configurator – Configuring Port I/O

C8051F93x/92x

Rev 0.7 7

4.4. CP210x USB to UART VCP Driver Installation

The MCU Card includes a Silicon Labs CP210x USB-to-UART Bridge Controller. Device drivers for the CP210x

need to be installed before the PC software can communicate with the MCU through the UART interface. Use the

drivers included CD-ROM or download the latest drivers from the website (www.silabs.com/interface-software).

1. If using the CD-ROM, the CP210x Drivers option will launch the appropriate driver installer. If downloading

the driver package from the website, unzip the files to a location and run the appropriate installer for the

system (x86 or x64).

2. Accept the license agreement and follow the steps to install the driver on the system. The installer will let

you know when your system is up to date. The driver files included in this installation have been certified by

Microsoft.

3. To complete the installation process, connect the included USB cable between the host computer and the

COM PORT USB connector (J5) on the MCU Card. Windows will automatically finish the driver installation.

Information windows will pop up from the taskbar to show the installation progress.

4. If needed, the driver files can be uninstalled by selecting the Windows Driver Package—Silicon

Laboratories... option in the Programs and Features window.

C8051F93x/92x

8 Rev 0.7

4.5. Silicon Labs Battery Life Estimator

The Battery Life Estimator is a system design tool for battery operated devices. It allows the user to select the type

of battery they are using in the system and enter the supply current profile of their application. Using this

information, it performs a simulation and provides an estimated system operating time. The Battery Life Estimator

is shown in Figure 6.

Figure 6. Battery Life Estimator Utility

From Figure 6, the two inputs to the Battery Life Estimator are battery type and discharge profile. The utility

includes battery profiles for common battery types such as AAA, AA, A76 Button Cell, and CR2032 coin cell. The

discharge profile is application-specific and describes the supply current requirements of the system under various

supply voltages and battery configurations. The discharge profile is independent of the selected power source.

Several read-only discharge profiles for common applications are included in the pulldown menu. The user may

also create a new profile for their own applications.

To create a new profile:

1. Select the profile that most closely matches the target application or choose the "Custom Profile".

2. Click Manage.

3. Click Duplicate.

4. Click Edit.

Profiles may be edited with the easy-to-use GUI (shown in Figure 7).

C8051F93x/92x

Rev 0.7 9

Figure 7. Battery Life Estimator Discharge Profile Editor

The Discharge Profile Editor allows the user to modify the profile name and description. The four text entry boxes

on the left hand side of the form allow the user to specify the amount of time the system spends in each power

mode. On the right hand side, the user may specify the supply current of the system in each power mode.

Since supply current is typically dependent on supply voltage, the discharge profile editor provides two columns for

supply current. The V2 and V1 voltages at the top of the two columns specify the voltages at which the current

measurements were taken. The Battery Life Estimator creates a linear approximation based on the input data and

is able to feed the simulation engine with an approximate supply current demand for every input voltage.

The minimum system operating voltage input field allows the system operating time to stop increasing when the

simulated battery voltage drops below a certain threshold. This is primarily to allow operating time estimates for

systems that cannot operate down to 1.8 V, which is the voltage of two fully drained single-cell batteries placed in

series.

C8051F93x/92x

10 Rev 0.7

The wakeup frequency box calculates the period of a single iteration through the four power modes and displays

the system wake up frequency. This is typically the "sample rate" in low power analog sensors.

Once the battery type and discharge profile is specified, the user can click the "Simulate" button to start a new

simulation. The simulation engine calculates the estimated battery life when using one single-cell battery, two

single-cell batteries in series, and two single-cell batteries in parallel. Figure 8 shows the simulation output window.

Figure 8. Battery Life Estimator Utility Simulation Results Form

The primary outputs of the Battery Life Estimator are an estimated system operating time and a simulated graph of

battery voltage vs. time. Additional outputs include estimated battery capacity, average current, self-discharge

current, and the ability to export graph data to a comma delimited text file for plotting in an external graphing

application.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Silicon Laboratories Mikrocontroller Handbücher

Silicon Laboratories

Silicon Laboratories C8051T60x-DK Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F91 Series Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories UG338 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F540DK Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Giant Gecko EFM32GG Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories CP2501DK Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories SLWSTK6104A Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F310 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories EFM32 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories AN515 Si4010 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F500 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F32 Series Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories EFM8SB2-SLSTK2011A Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F99 Series Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F38 Series Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051T622 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F310-TB Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories CP2102N-MINIEK Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F35 Series Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories SiM3U1xx Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F912 Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories Telegesis ETRX357DVK Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories BG22 Explorer Kit Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories EFM8SB1-SLSTK2010A Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung