SilverStone AD120-DC Bedienungsanleitung
AD120-DC / AD60-DC
120 / 60W DC to DC board and 120 / 60W AC to DC adapter combo kit
Maximum Output of 120W / 60W
120 / 60W DC-DC power board with 120 / 60W 12V efficiency level VIAC-DC Power Adapter & power cord
Mylar insulation design, easy to install
Black wire design
Built-in multiple protection circuitry for maximum protection during operation
SPECIFICATION
Adapter Series
SST-AD60-DC
SST-AD120-DC
60W / 120W WATTS SWITCHING POWER SUPPLY
with AC adapter
1.1 VOLTAGE
1.2 CURRENT
AD60-DC
12Vdc / 6.0A max
AD120-DC
12Vdc / 12.0A max
1.3 POWER EFFICIENCY
90% at full load (LOAD REGULATION TEST TABLE LOAD 1、2)
1.0 INPUT:
MINIMUM NOMINAL MAXIMUM UNITS
11.4 12 12.6 Vdc
A. DC Board
P1
AD60-DC
AD120-DC
＊1 When input voltage 11.4~11.8V regulation +5,-10
﹪
of +12Vdc
output.
＊2 The continuous total output power is 60W max.
•Total combined +12V output load not exceed 5.0A
＊3 Add 0.1uF and 10uF capacitors across output terminal during
ripple & noise test.
＊4 LOAD REGULATION TEST TABLE:
2.0 OUTPUT:
Voltage +5V +3.3V +12V -12V +5Vsb
＊
Max load 7.0A 7.0A 5.0A 0.1A 2.0A
＊
Regulation
+5,-5
﹪﹪
+5,-5
﹪﹪
+5,-5
﹪﹪
+10,-10
﹪﹪
+5,-5
﹪﹪
＊
Ripple&Noise 50mV 50mV 120mV 120mV 50mV
1
2
3
1
2
3
+5V +3.3V +12V -12V +5Vsb
LOAD1 (100
﹪
﹪
) 3.49A 3.49A 2.18A 0.04A 0.87A
LOAD2 (50
﹪
﹪
) 1.32A 1.32A 1.5A 0.0A 0.2A
LOAD3 1.50A 1.5A 1.0A 0.1A 2.0A
LOAD4 7.0A 2.5A 1.0A 0.1A 0.5A
LOAD5 3.0A 7.0A 1.5A 0.1A 0.5A
LOAD 6 0.0A 0.0A 5.0A 0.0A 0.0A
Voltage +5V +3.3V +12V -12V +5Vsb
＊
Max load 12.0A 12.0A 10.0A 0.15A 3.0A
＊
Regulation +5,-5
﹪
﹪
+5,-5
﹪
﹪
+5,-5
﹪
﹪
+10,-10
﹪
﹪
+5,-5
﹪
﹪
＊
Ripple&Noise 50mV 50mV 120mV 120mV 50mV
P2
＊1 When input voltage 11.4~11.8V regulation +5,-10
﹪
of +12Vdc
output.
＊2 The continuous total output power is 60W max.
•Total combined +12V output load not exceed 5.0A
＊3 Add 0.1uF and 10uF capacitors across output terminal during
ripple & noise test.
＊4 LOAD REGULATION TEST TABLE:
TTL High/PS-OFF; TTL Low/PS-ON
VIL=0.8Vmax, IIL=-1.6mAmax @Vin=0.4V
VIH=2.0Vmin @Iin=-200uA, VIH=5.25Vmax @open ckt.
2.1 REMOTE ON/OFF
100-500 msec.
2.2 POWER GOOD DELAY
2000 msec max.At Nominal Line Full Load.
2.3 TURN-ON DELAY TIME
+/- 10% max with 20% load change on all outputs are 50% of the rated.
Load slew rated 1.0A/uS and capacitive load as below :
2.4 TRANSIENT OVERSHOOT
+5V +3.3V +12V -12V +5Vsb
LOAD1(100
﹪
﹪
) 5.0A 5.0A 5.8A 0.1A 1.5A
LOAD2(20
﹪
﹪
) 1.0A 1.0A 1.1A 0.0A 0.5A
LOAD3 12.0A 1.0A 0.1A 0.1A 3.0A
LOAD4 12.0A 2.5A 2.0A 0.1A 1.5A
LOAD5 3.0A 12.0A 5.0A 0.1A 1.0A
LOAD6 0.0A 0.0A 10.0A 0.0A 0.0A
+5V +3.3V +12V -12V +5Vsb
10000uF 10000uF 10000uF 330uF 10000uF
P3
20ms max at full load.
2.5 RISE TIME
Output voltage regulation +10,-10﹪
When OVP or short protection is triggered, the main outputs
will be latched off. The main outputs can be reset by cycling
the DC remote on/off.
2.6 DYNAMIC TEST
+5V output : 28A max.
+3.3V output : 28A max.
+12V output : 10A max.
3.1 OVER CURRENT PROTECTION
AD60-DC
+3.3V output 2.4 Vmax.
+5.0V output 3.7 Vmax.
+12.0V output 9.5 Vmax.
AD120-DC
+3.3V output 2.0 Vmax.
+5.0V output 3.3 Vmax.
+12.0V output 8.5 Vmax.
+3.3V output 4.1 Vmax.
+5.0V output 6.5 Vmax.
+12.0V output 14.4 Vmax.
3.2 UNDER VOLTAGE PROTECTION
3.3 OVER VOLTAGE PROTECTION
All output to GND.
3.4 SHORT PROTECTION
3.0 PROTECTION:
P4
4.1 OPERATING TEMP. 0 °C to +40 °C
4.2 STORAGE TEMP. -20 °C to +70 °C
4.3 OPERATING HUMIDITY 20% to 90%,non-condensing
4.4 STORAGE HUMIDITY 5% to 95%, non-condensing
4.5 OPERATING ALTITUDE 0 to 10,000feet
4.6 STORAGE ALTITUDE 0 to 50,000 feet
100K hrs minimum
AD60-DC
DC board dimension: WxLxH=148.5x30x25mm
AD120-DC
DC board dimension: WxLxH=160x45x25mm
5.0 MTBF at 25°C(demonstrated)
6.0 DIMENSIONS
4.0 ENVIRONMENT:
P5
60W
The total output power, under steady state conditions, shall not
exceed 60 W.
2.0 Output requirement
Output power
Output voltage and current
Table 2 - Output Voltage and Current
Under any combination of line and load variation and
environmental conditions, all outputs shall remain within
tolerance as defined in Table 2. Output voltage(s) shall be
measured at the load side of output connector.
Output
Voltage
Voltage Range Current Range
Lower
Limit Upper
Limit Minimum
Load Full rated
load PK Load
+12.0V 11.40V 12.60V 0.0A 5.0A --
P6
Power supply shall operate within specification from 90 to 264Vrms or provide automatic
switching in two ranges. The table below shows common input voltage range.
Maximum steady state input current shall not exceed 1.7 A for any line voltage specified
in Input voltage range define.
1.0 Input voltage range
Input current
B. AC adapter
Input Range Minimum Nominal Maximum Unit
90 100 -240 264 Vac, rms
3.0 Ptotection
The power supply shall provide with over voltage protection such
that under any single component failure.
The power supply provides output over voltage protected in latch
off by zener diode, and no damage to customer device.
60W
The power supply shall be protected when operating any output in
overload condition. The power supply shall be shut down and no
any damage when the over current condition occurs on the output,
and It will be auto-recovered when the failure is removed.
Over voltage protection
Over current protection
P7
120W
Unit total output power, under steady state conditions, shall not
exceed 120 W .
Output power
Under any combination of line and load variation and
environmental conditions, all outputs shall remain within
tolerance defined in Table 2. Output voltage(s) shall be
measured at the load side of output connector.
Output voltage and current
Table 2 - Output Voltage and Current
Output
Voltage
Voltage Range Current Range
Lower
Limit Upper
Limit Minimum
Load
Full
rated
load Peak Load
1 +12V 11.4V 12.6V 0A 10A 13A@10s
(115/230VAC)
Short circuit protection
4.0 AC adapter external dimension
Power supply shall have self-limiting protection to protect against
short circuit or overload conditions. No damage to the supply
shall result from a continuous or intermittent short circuit condition.
60W
Dimension without cable: 116mmX52.4mmX31.3mm
Cable length:1200mm±20mm
120W
Dimension without cable: 168mmX71mmX37.5mm
Cable length:1200mm±20mm
P8
60W
During turn on or turn off, the output overshoot shall not exceed
nominal output voltage by more than 5% , and output shall not
change its polarity with respect to its return line.
120W
During turn on, turn off condition, the output overshoot shall not
exceed nominal voltage by more than 10% , and output shall not
change its polarity with respect to its return line.
120W
Over current protection shall be operated within specify
14.5A (min) ~ 20A (Max) , defined in section 2.3.1 at 100~240Vac
line input or temperature conditions.
Overshoot and undershoot
Table 4 –Over current protection
Output
Voltage
Over current protection Test condition
Lower Limit Upper Limit Input
voltage:100Vac
60Hz or 240Vac
50Hz.
+12.0V 5.80A 9.00A
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere SilverStone Adapter Handbücher
SilverStone
SilverStone ECD01 Bedienungsanleitung
SilverStone
SilverStone FP510 Bedienungsanleitung
SilverStone
SilverStone FP57 Bedienungsanleitung
SilverStone
SilverStone ECM20 Bedienungsanleitung
SilverStone
SilverStone MUA01 Bedienungsanleitung
SilverStone
SilverStone ECM24 Bedienungsanleitung
SilverStone
SilverStone ECWA2 Bedienungsanleitung
SilverStone
SilverStone SDP12 Bedienungsanleitung
SilverStone
SilverStone SST-PP08B Bedienungsanleitung
SilverStone
SilverStone SST-ECM23 Bedienungsanleitung
