Sim2 GRAND CINEMA HT5000 Bedienungsanleitung

HT5000

DLP™VIDEO

PROJECTOR

RS-232C

CONTROL

SPECIFICATIONS

Document Revision 1.0 (15 February 2007)

HT5000

RS-232C CONTROL SPECIFICATIONS

Table of Contents

1. INTRODUCTION 3

2. CONNECTION 3

3. COMMANDS 4

4. EXAMPLE 5

5. WARNING 5

Revision History:

Revision Date Software Version Description of Change

1.0 15 February 2007 3.10.68 or higher Initial version.

HT5000

RS-232C CONTROL SPECIFICATIONS

1. Introduction

This document describes the communication and data formats used to control SIM2 HT5000 projector via

RS-232C port.

2. Connection

Switch off the Personal Computer and the Projector before connecting RS 232C cable.

Use a standard serial cable with 9 pin female to the Personal Computer and 9 pin male to the Projector: pin

2 connects to pin2, pin 3 to pin 3 and pin 5 to pin 5.

SIM2 HT5000 RS-232C Port is described as follows.

SIM 2 HT5000 RS-232C Control Port:

Pin No Signal Definition

1 N/A Not used

2 TD Transmit data

3 RD Receive data

4 N/A Not used

5 GND Ground

6 N/A Not used

7 N/A Not used

8 N/A Not used

D-SUB 9-pin

(female)

9 N/A Not used

Switch on the Personal Computer and, after start up, switch on the Projector.

Load a suitable communication software onto your Personal Computer, and set the Serial Port Parameters as

shown below.

Communication Parameters:

Parameter Value

Transfer Rate 19200 bps

Data Bits 8

Parity Bit None

Stop Bit 1

Flow Control None

Set Send Mode and Read Mode to HEX.

HT5000

RS-232C CONTROL SPECIFICATIONS

3. Commands

The following commands send simulated Remote Control input to SIM2 HT5000 projector.

Remote Control Keycodes:

Key Command

STANDBY BE EF 02 06 00 51 E4 48 01 00 00 00 00

0 / ON (1) BE EF 02 06 00 6B E6 52 01 00 00 00 00

1 (2) BE EF 02 06 00 80 E5 49 01 00 00 00 00

2 (2) BE EF 02 06 00 B3 E5 4A 01 00 00 00 00

3 (2) BE EF 02 06 00 62 E4 4B 01 00 00 00 00

4 (2) BE EF 02 06 00 D5 E5 4C 01 00 00 00 00

5 (2) BE EF 02 06 00 04 E4 4D 01 00 00 00 00

6 (2) BE EF 02 06 00 37 E4 4E 01 00 00 00 00

7 (2) BE EF 02 06 00 E6 E5 4F 01 00 00 00 00

8 (2) BE EF 02 06 00 89 E7 50 01 00 00 00 00

9 (2) BE EF 02 06 00 58 E6 51 01 00 00 00 00

10 (3) BE EF 19 0A 00 E2 7E 00 00 09 00 00 00 00 00 00 00

11 (3) BE EF 19 0A 00 F7 3E 00 00 0A 00 00 00 00 00 00 00

12 (3) BE EF 19 0A 00 3B FF 00 00 0B 00 00 00 00 00 00 00

13 (3) BE EF 19 0A 00 DD BE 00 00 0C 00 00 00 00 00 00 00

14 (3) BE EF 19 0A 00 11 7F 00 00 0D 00 00 00 00 00 00 00

ESC BE EF 02 06 00 0D E6 54 01 00 00 00 00

CURSOR UP BE EF 02 06 00 DC E7 55 01 00 00 00 00

CURSOR LEFT BE EF 02 06 00 EF E7 56 01 00 00 00 00

CURSOR RIGHT BE EF 02 06 00 3E E6 57 01 00 00 00 00

CURSOR DOWN BE EF 02 06 00 C1 E6 58 01 00 00 00 00

MENU LEFT (-) BE EF 02 06 00 10 E7 59 01 00 00 00 00

MENU RIGHT (+) BE EF 02 06 00 23 E7 5A 01 00 00 00 00

FREEZE BE EF 02 06 00 F2 E6 5B 01 00 00 00 00

MEMORY BE EF 02 06 00 45 E7 5C 01 00 00 00 00

F1 BE EF 02 06 00 94 E6 5D 01 00 00 00 00

F2 BE EF 02 06 00 76 E7 5F 01 00 00 00 00

INFO BE EF 02 06 00 A7 E6 5E 01 00 00 00 00

AUTO BE EF 02 06 00 79 E2 60 01 00 00 00 00

ASPECT BE EF 02 06 00 A8 E3 61 01 00 00 00 00

HT5000

RS-232C CONTROL SPECIFICATIONS

(1)

- When the unit is in Standby state, this command switches the unit on and the last source memorised

prior to switch off is automatically selected.

- When the unit is On, this command displays the Source Selection windows of the OSD.

(2)

When the unit is in Standby state, this command switches the unit on and the corresponding source is

selected.

(3)

When the unit is in On, this command selects the corresponding source.

The response of the unit to a correct Remote Control Key Code consists of a single byte: 06.

4. Example

1. Send the simulated "SWITCH ON FROM STANDBY" Remote Control keycode.

Remote Control allows Switching on from Standby via the key "0".

Send the code relative to key "0":

BEEF0206006BE6520100000000.

The projector switches on and the last source memorised prior to switch off is automatically selected.

The projector returns the response code: 06 (Acknowledged with no error).

2. Send the simulated "MENU RIGHT" Remote Control keycode.

Send the packet:

BEEF02060023E75A0100000000.

The OnScreen Display appers on the screen.

The projector returns the response code: 06 (Acknowledged with no error).

5. Warning

Command execution time may vary from few milliseconds to 500 milliseconds, depending on the operation

that have been requested.

If the unit is busy when a command is sent, the unit may not accept the command. If several commands are

to be sent one after the other, sufficient time between them should be allowed.

Inhaltsverzeichnis

Andere Sim2 Projektor Handbücher

Sim2

Sim2 EVSX1 Bedienungsanleitung

Sim2

Sim2 xTV Series Bedienungsanleitung

Sim2

Sim2 LUMIS20TH Bedienungsanleitung

Sim2

Sim2 Grand Cinema HT380 Betriebsanleitung

Sim2

Sim2 AR Bedienungsanleitung

Sim2

Sim2 XTV 4K INV Gebrauchsanweisung

Sim2

Sim2 DLP RS-232C Bedienungsanleitung

Sim2

Sim2 DLP Video Projector C3X Link Bedienungsanleitung

Sim2

Sim2 Grand Cinema HT200 DMF Betriebsanleitung

Sim2

Sim2 Grand Cinema HT 200 Betriebsanleitung

Sim2

Sim2 PRO5DL Bedienungsanleitung

Sim2

Sim2 NERO 3D HB Bedienungsanleitung

Sim2

Sim2 Lumis HOST C3X Betriebsanleitung

Sim2

Sim2 Grand Cinema HT 300XTRA-H Betriebsanleitung

Sim2

Sim2 HT 280E Betriebsanleitung

Sim2

Sim2 M.150S Bedienungsanleitung

Sim2

Sim2 Sirio Bedienungsanleitung

Sim2

Sim2 DOMINO DTV S Bedienungsanleitung

Sim2

Sim2 SuperCube Bedienungsanleitung

Sim2

Sim2 Grand Cinema HT 200 Bedienungsanleitung

Sim2

Sim2 CRYSTALCUBE Bedienungsanleitung

Sim2

Sim2 NERO4 UHD Bedienungsanleitung

Sim2

Sim2 DLP Video Projector C3X Link Betriebsanleitung

Sim2

Sim2 TEATRO 80 Betriebsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung