Sim2 NERO 3D HB Bedienungsanleitung
SIM2 Multimedia
Nero 3D-1,
Nero 3D-2,
Nero 3D HB
User Guide
Contents
3Important information
Safety
3D content
En ironment
Notice
7Chapter 1: Introduction
About This User Guide
Key Features and Benefits
System Components
Optional Accessories
9Chapter 2: Overview
Remote Control
Projector Keypad
Connections
3D IR Emitter
3D Glasses
13 Chapter 3: Installation
Location
Mounting
Connections
Switching On and Off
19 Chapter 4: Operation
Viewing 3D Content
3D Menu
Input Menu
Main Menu
Picture
Image
Setup
Menu
Memories
Info
Quick Menus
Messages
36 Chapter 5: roubleshooting
38 Chapter 6: Specifications
40 Chapter 7: Projection Distances
41 Chapter 8: Dimensions
Nero 3D
User Guide
2
Important information
Safety
To reduce the risk of electrocution, disconnect the power cord on the
rear panel before remo ing the top co er of the projector. For technical
ser ice refer to trained personnel authorized by the manufacturer.
If the lamp suddenly explodes with a loud bang, turn off the projector immediately
and air the room thoroughly. Do not attempt to restart the projector and do attempt
to replace the bulb: contact your local ser ice center.
Read this guide
Read all chapters of this guide carefully before switching on the projector. This guide
pro ides basic instructions for operating the Nero 3D-1/3D-2/3D HB projectors. Install-
ation, preliminary adjustments and procedures that necessitate the remo al of the
top co er and contact with electrical components must be performed by authorized,
trained technicians. To ensure safe operation and long term reliability use only the
power cords supplied by the manufacturer. Obser e all warnings and precautions.
Keep this guide for future consultation.
Do not touch internal parts of the projector
Inside the housing there are electrical parts carrying dangerously high oltages and
parts operating at high temperature. Ne er open the housing. Entrust all ser icing and
repair work to a SIM2 Authorized Ser ice Center. Opening the housing oids the war-
ranty.
Disconnect the appliance from the power supply
The de ice that disconnects the projector from the mains is the power plug. Ensure
that the power cord plugs and the electrical outlets are easily accessible during install-
ation operations. Pull the plug, not the cord, to disconnect the projector from the
mains. Use only the specified power supply. Connect the projector to a mains electric-
al supply with rated oltage of between 100-240 V AC, 50/60 Hz and equipped with a
protecti e earth connection. If you are not sure of your domestic mains rating, contact
an electrician. Take care to a oid o erloading the power socket and any extension
leads.
Switching the projector off
Pay attention to the switch off procedure for the projector. The projector must always
be brought back to the standby state to allow the projector to carry out the cooling
procedure. Should this not happen, for example due to a power cut, the projector may
enter a state of protection that leads to switch-on being blocked. This block will last
until the internal components of the projector ha e completely cooled down.
Changing the fuses
Before changing the fuse, disconnect the projector from the mains power supply. The
fuse compartment is next to the power supply connector. Remo e the fuse holder
Important information Nero 3D
User Guide
3
with a flat head screwdri er and replace the fuse. Fit the replacement fuse. Use only
type T 10 A L H fuses for the projector.
Be careful with cables
Make sure cables are routed so that people are not impeded or become a trip hazard.
Keep all cables away from children. Install the projector as close to the wall socket as
possible. A oid stepping on power cords, make certain they do not become tangled,
and ne er jerk or tug them; do not expose them to sources of heat, and make sure
they do not become knotted or crimped. If the power cords become damaged, stop
using the projector and request the assistance of an authorized technician.
Disconnect the projector from the mains power during electrical storms and when
not in use
To pre ent damage from lightning strikes in the icinity, disconnect the projector dur-
ing storms or when the projector is going to be left unused for a long time.
Avoid contact with liquids and exposure to damp
Do not use the projector near water (sinks, tubs and so on); do not place objects con-
taining liquids on or near the projector and do not expose it to rain, humidity, drops of
water or sprays; do not use water or liquid detergent to clean it.
Place the projector on a stable surface
Place the projector on a stable surface or use a suitable ceiling mounting bracket. Ne -
er place the projector on its side or rear, on the lens or top panel.
Do not allow the projector to overheat
To pre ent o erheating, allow a free space of at least 0.25 m (10 in.) on the left, right
and rear sides of the projector. Do not obstruct the entilation slots. Do not place the
projector near heat sources such as heaters, radiators or other de ices (including
amplifiers) that generate heat. Do not place the projector in an area where there is
insufficient space (shel ing units, bookshel es and so on) and in general a oid placing
it in poorly entilated areas as this may pre ent sufficient cooling and significantly
reduce lamp life.
Never look directly at the projection lamp
Ne er look directly into the lens when the lamp is on as the intense light may damage
your eyes. Take particular care that children cannot do so.
ake special care regarding movement of the lens
Do not place objects in the slots on the side of the lens and also ensure that ertical
lens mo ements are not impeded by external objects.
Do not insert objects through the openings in the projector
Make sure that no objects are inserted inside the projector. If this should occur, dis-
connect the projector from the power supply immediately and call an authorized tech-
nician.
Power saving
We ad ise disconnecting the projector from the power supply when not in use. In this
way you will achie e considerable power sa ings while at the same time protecting in-
ternal electrical parts from wear.
Important information Nero 3D
User Guide
4
3D content
Discomfort (such as eye strain, headaches, motion sickness, nausea, dizziness, disori-
entation) may be experienced while watching 3D content. In this case, stop watching
and consult a doctor if symptoms are se ere.
Consult a doctor before allowing young children (especially those under six years old)
to watch 3D content as their isual system is still under de elopment.
Monitor children (including teenagers) watching 3D content, as they are more at risk
of experiencing discomfort and less inclined to report symptoms.
Indi iduals who may be susceptible to epileptic seizures or strokes (on the basis of
personal and family history) should consult a doctor before watching 3D content.
All iewers should take regular breaks from watching 3D content. Length and fre-
quency of these breaks may ary from person to person.
Environment
This product contains materials deri ed from natural resources during its manufac-
ture. It may contain materials that constitute a health and en ironmental hazard. To
pre ent harmful materials from being released into the en ironment and to promote
the use of natural materials, SIM2 pro ides the following information regarding the
disposal and recycling of the product.
Waste electrical and electronic materials (WEEE) should ne er be disposed of in nor-
mal urban waste disposal facilities.
The label on the product, shown here, indicating a canceled garbage can,
is intended to remind you that the product requires special handling at
the end of its ser ice life. Materials such as glass, plastic and some chem-
ical compounds are reco erable and can be recycled for reuse.
Obser e the following instructions:
•When you no longer wish to use your electrical and electronic equipment,
take it to your local waste disposal facility for recycling.
•You may return your old equipment to your SIM2 Authorized Dealer free of
charge when you buy a new product that is equi alent or has the same func-
tions as the old one. Contact SIM2 to find your local dealer.
•If you need more information regarding recycling, reuse and product ex-
changes, contact SIM2 customer ser ice.
Lastly we suggest further measures to safeguard the en ironment, such as recycling of
internal and external packaging (including that used for shipping) in which the product
was deli ered. With your help, we can reduce the amount of en ironmental resources
required to make electric and electronic equipment, reduce the use of waste tips for
used equipment and, in general, impro e our quality of life by making sure that haz-
ardous materials are correctly scrapped. Incorrect treatment of the product at the end
of its ser ice life and failure to follow the abo e disposal instructions are punishable
under local legislation.
Important information Nero 3D
User Guide
5
Product disposal
The lamp inside this projector contains mercury and may be subject to
special disposal or recycle regulations. Dispose or recycle in accordance
with local laws. For more information contact the Electronic Industries
Alliance at www.eiae.org or check www.lamprecycle.org
Notice
The appliance has been subjected to exhausti e operating tests by SIM2 to guarantee
the highest quality. The projector bulb life should thus initially be around 30-60 hours.
In addition to the customary checks, the Quality Control department also runs addi-
tional statistical tests before shipment. In such cases, the packaging may show signs of
ha ing been opened, and the hours of lamp operation may pro e to be higher than
those normally shown when only standard tests are performed.
As the optical system of the Nero 3D-1/3D-2/3D HB is extremely compact and has the
purpose of de eloping ery high brightness and contrast, it is possible that a small
quantity of light is isible outside of the projection area and will ary depending on
the type of lens used and the zoom and shift setup. This characteristic of the optical
system is to be deemed as normal. In order to reduce this effect SIM2 recommends
that the area surrounding the projection screen is as dark as possible.
Important information Nero 3D
User Guide
6
1 Introduction
The Nero 3D-1/3D-2/3D HB are high-end compact 1-chip DLP 3D single unit projectors
that utilize SIM2’s state-of-the-art optical technologies to produce images with excep-
tional black le el and contrast performance.
The Nero 3D-1/3D-2/3D HB are able to emulate the best 3D cinema projection sys-
tems, in terms of color fidelity, definition and depth of image. These are all con eyed
accurately, as is the fluid motion of fast-action mo ies and sports. This all adds up to
an incredible 3D experience at home.
The Nero 3D-1/3D-2/3D HB are designed for use with large screen sizes – up to 5 m
(16.5 ft.) wide. A choice of three high quality glass lenses (T1, T2 and T3) is a ailable,
gi ing the projectors a total throw ratio of 1.37-3.90:1.
To aid calibration SIM2’s Li e Color Calibration software enables complete control
o er:
•primary, secondary and white point color coordinates
•gamma tables
allowing calibration experts to accurately calibrate the final image ia a user-friendly
application for Windows-based computers.
About his User Guide
This User Guide describes how to set up and operate the following projectors:
•Nero 3D-1
•Nero 3D-2
•Nero 3D HB
Except where otherwise indicated, the information in this guide applies to all the pro-
jectors listed abo e, that will be referred to as “Nero 3D”.
Key Features and Benefits
•high picture quality: SIM2 renown image processing and the latest 0.95 in.
1080p DMD from Texas Instruments
•precision optics: patented SIM2 ALPHAPATH compact die-cast light engine
with precision glass optics
•artifact-free fast-action images: SIM2 PureMotion processing
•high resolution: actual full HD 3D images, without blur and ghosting
•comfortable 3D iewing: high brightness ghost-free sharp images
•immersi e 3D effect: large screen sizes thanks to high brightness images
•3D wide iewing angle: stereo separation independent from iewing angles
•screen flexibility: no constraints in the choice of the screen material
•compatibility: no need of dedicated sources and preprocessing for 3D iewing
•longer lamp life: affordable and reliable UHP lamps
1 Introduction Nero 3D
User Guide
7
System Components
Your Nero 3D DLP projector ships with the following items:
•1 x backlit remote control unit (with four AAA/LR03 batteries)
•3 x AC power cords (US, EU and UK), 2 m (6.6 ft.) long
•3 x jacks for 12 V output connectors
•1 x 4.0-millimeter Hex wrench (for lens shift adjustment)
•1 x User guide (this document)
•1 x CD with Li e Color Calibration software (for Windows-based computers)
If any items are missing or damaged, contact your SIM2 Authorized Dealer as soon as
possible. Keep the original packaging in case anything has to be shipped.
Optional Accessories
•Visus system (7 SIM2 Visus acti e shutter glasses and 1 IR emitter for SIM2
Visus acti e shutter glasses)
•Visus box (8 SIM2 Visus acti e shutter glasses)
•Uni ersal system (6 uni ersal acti e shutter glasses and 1 IR emitter for uni-
ersal acti e shutter glasses)
•Uni ersal box (8 uni ersal acti e shutter glasses)
•Projector ceiling bracket
•Anamorphic lens systems (fixed or motorized)
1 Introduction Nero 3D
User Guide
8
2 Overview
Remote Control
❶Turn backlight on for about 5
seconds
❶
❸
❹
❺
❼
❽
❾
⓫
⓬
⓮
❷
❻
❿
⓭
⓰
⓯
❷ turns the projector off
❸1-9 select inputs and turn the projector
on
❹0enters OSD Input menu and turns
the projector on
❺●OK enters submenus, confirms ac-
tions
❻ESC exits OSD
❼
▴
◂ ▸
▾
select menu items, adjust settings or
cycle through the test patterns
❽
MENU
+ / -
enter OSD Main menu and select
the desired section, each press of
the key selects the next tab in the
menu
❾II 3D enters 3D menu
❿Memory enters Memories menu
⓫ ⓬ F1, F2
perform user-defined actions (de-
fault assignments are: F1 = Zoom, F2
= Focus)
⓭Info displays projector Info
⓮A Auto performs Auto Adjustment
⓯Aspect enters Aspect Quick menu
⓰Not used
Custom Remotes
You can use your own IR remote control to control your Nero 3D projector.
•If you are using a remote control with learning capabilities, use the projector
remote control to teach the commands to your remote.
•If you are using a programmable remote control, the setup software probably
allows importing of Pronto Hex codes. See SIM2 Nero 3D-1/3D-2/3D HB IR
Control for a list of all the projector codes in Pronto Hex format, including a
number of discrete codes for:
◦Aspects
2 O er iew Nero 3D
User Guide
9
◦Memories
◦3D Controls (3D Mode and Input Formats)
Operation
The Nero 3D projector has two IR recei ers, one on the front and one on the back of
the unit. The operati e range of the remote control is approximately 10 m (33 ft.).
Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR recei er you are pointing to. You can point the remote control to-
wards the screen, as the IR beam is reflected by the screen towards front IR recei er
of the projector. In this case the effecti e range of the remote control may be smaller
than declared.
Batteries
To install batteries in the remote control:
1. Open the battery co er.
2. Insert four AAA (LR03) batteries making sure the polarities match the + marks
inside the battery compartment.
3. Replace the co er.
Replace the batteries with new ones when the operating range of the remote control
decreases. Dispose of used batteries according to local regulations. Make sure you do
not mix old and new batteries or different types of batteries.
Warning: If you will not use the remote control for a long time, remo e the batteries
to a oid battery leakage.
Projector Keypad
turns the projector on or off
◂ ▸ ▴ ▾ select menu items, adjust settings or switch test patterns
MENU enters OSD Main menu and selects the desired section
ESC exits OSD
SOURCE/Oenters OSD Input menu/selects a menu item
2 O er iew Nero 3D
User Guide
10
Andere Handbücher für NERO 3D HB
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Sim2 Projektor Handbücher
Sim2
Sim2 Mico 40-50-ST Betriebsanleitung
Sim2
Sim2 GRAND CINEMA HT HT500 LINK Betriebsanleitung
Sim2
Sim2 C3X1080 Betriebsanleitung
Sim2
Sim2 PRO5000 Bedienungsanleitung
Sim2
Sim2 NERO 3 PLUS Bedienungsanleitung
Sim2
Sim2 Grand Cinema HT305 E Bedienungsanleitung
Sim2
Sim2 xTV Series Bedienungsanleitung
Sim2
Sim2 LUMIS 3D-S Bedienungsanleitung
Sim2
Sim2 D80 Betriebsanleitung
Sim2
Sim2 Grand Cinema HT 200 Bedienungsanleitung
Sim2
Sim2 Domino 35 Bedienungsanleitung
Sim2
Sim2 C3XE Betriebsanleitung
Sim2
Sim2 Gold Series Bedienungsanleitung
Sim2
Sim2 Pro-C3 Betriebsanleitung
Sim2
Sim2 DLP Video Projector C3X Link Bedienungsanleitung
Sim2
Sim2 D60 Bedienungsanleitung
Sim2
Sim2 Grand Cinema HT200 DMF Betriebsanleitung
Sim2
Sim2 Grand Cinema HT 200 Betriebsanleitung
Sim2
Sim2 C3X 1080 Betriebsanleitung
Sim2
Sim2 SVD800 HD Millennium Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
