Simple S100 Bedienungsanleitung
Installation Guide
© 2017 EcoFactor, Inc.
1
Thermostat and Wall Plate
Manuals and Wiring Labels Screws and Wall Anchors
Trim Plate
The wall plate comes snapped into
the back of the thermostat.
The optional trim plate can
cover unnished areas under the
old thermostat. It can be used
horizontally or vertically.
In the Box
2
For a Wi-Fi connected installation, visit install.thesimple.com to
sign up for an account and view on-line instructions.*
Installing this thermostat usually takes around 45 minutes, depending
on your existing thermostat and wiring requirements. A common wire
(C-wire) or other 24VAC power source is required.
Recommended Tools
*If you are eligible for professional installation, online install is not supported.
WARNING: Line voltage and millivolt systems are not supported.
Tools and Preparation
3
Step 1 – Remove power to the
system
Step 2 – Remove the existing
thermostat faceplate
Locate your breaker or master
power switch that controls your
heating and/or cooling system, and
turn off the power.
Take a picture of existing wiring
as a reference.
If you see thick wires and plastic
caps, then STOP. The S100 is not
compatible with 120V line voltage
systems.
Installation Steps
4
Step 3 – Attach wire labels
The jumper wire can be discarded.
Your thermostat has an internal
jumper.
Match the supplied wire labels to the
existing wiring. If there is no match,
consult the Wiring Guide after this
section. Disconnect the existing wiring
before removing the wall plate.
You can wrap wires around a
pencil so they do not fall into the
wall.
Step 4 – Remove any existing RC or
RH jumper wire
Step 5 – Remove the existing
wall plate
5
If the optional trim plate is needed,
place it between the wall plate and
the wall.
Match the wire labels to the
terminal names on the wall plate.
The wall plate has levers for each
terminal position. Lift the lever
before inserting the wire. Push the
lever back down to lock the wire in
place.
Step 6 – Mount the wall plate Step 7 – Connect the wires
6
Ensure that all four corners are
snapped into place.
Verify that the thermostat display
turns on. The system will be OFF
when rst installed. Do not press
buttons or change system settings
until it has been fully congured.
Step 8 – Attach thermostat to wall
plate
Step 9 – Turn power back on
7
Match your existing wiring to the S100 terminals using the table below.
Terminal Function
RC 24VAC for cooling.
RH 24VAC for heating. If there is only one R wire (R, RH, RC) then
connect it to RH. May be labeled V or VR for Lennox.
C Common wire. May be labeled X for Rheem, Ruud, or Lennox;
B for Trane, York.
Y 1st stage compressor, A/C or heat pump. May be labeled M
for Lennox.
Y2 2nd stage compressor, A/C or heat pump.
W/E 1st stage heating, or heat pump emergency heat. Some
heat pumps may designate emergency heat as E or X2, or
auxiliary heat as W1 or W2. May be labeled Y for Lennox.
W2 2nd stage heating. Not used for heat pumps.
O/B Heat pump changeover valve.
G Fan control. Optional for gas furnace, required for A/C and
electric heat strip or furnace. May be labeled F for Lennox.
L Fault detection for heat pumps.
Wiring Guide
8
This thermostat is intended to be connected to your Wi-Fi network. However,
it is fully functional as a conventional thermostat when disconnected.
If you wish to use the thermostat as a disconnected device, the system
heating and cooling conguration must be congured using the Advanced
Menu before use.
If the thermostat was previously congured to use Wi-Fi, this connected
conguration must rst be cleared with a Factory Reset.
The default conguration for your thermostat is for conventional heating
and cooling. If you have a heat pump or other conguration, do not use the
MODE button until the thermostat has been congured.
Press and hold both the MENU tand MODE buttons for 5 seconds to enter the
Advanced Menu.
Press DOWN until RESET is shown.
Press MODE and CONFIRM will start ashing.
Hold MODE for 5 seconds to clear all settings.
Step 1: Factory Reset (if needed)
Disconnected Conguration
Andere Handbücher für S100
1
Inhaltsverzeichnis
Andere Simple Thermostat Handbücher
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
