Simplex 4100-S1 Betriebsanleitung

4100U-S1 Fire Indicator Panel

Programming Guide

Australian

Programming

Guide

LT0400

Iss 1.4

Document: LT0400 4100U-S1 Programming Guide

Issue 1.4 15 December 2010 Page iii

AMENDMENT LOG

1.0 28 November 2006 Original Issue

1.1 4 June 2008 Updated to match 12.05.02 Exec release

1.2 19 August 2010 Updated with Aust. message library loaded as primary

1.3 29 September 2010 Revised AS1668 Section

1.4 15 December 2010 Updated to match 12.06.01 Exec release and new

templates.

Windows® is a registered trademark of Microsoft Corporation ®

4100U-S1 Programming Guide Document: LT0400

Page iv 15 December 2010 Issue 1.4

TABLE OF CONTENTS

AMENDMENT LOG iii

1INTRODUCTION 1-1

1.1 ABOUT THIS MANUAL 1-2

1.2 BEFORE YOU START 1-3

2SYSTEM OVERVIEW 2-1

2.1 GENERAL DESCRIPTION 2-2

2.2 PROGRAMMING 2-3

3ABOUT THE PROGRAMMING TOOLS 3-1

3.1 GENERAL 3-2

3.2 4100U PROGRAMMER 3-2

3.3 4100U-S1 CONFIGURATION TEMPLATES 3-2

3.4 4100U PROGRAMMER INSTALLATION AND LAUNCH 3-2

3.5 STEPS TO CONFIGURING A NEW SYSTEM 3-3

3.6 UPGRADING AN EXISTING CONFIGURATION 3-3

4CREATING A CONFIGURATION 4-1

4.1 CREATING A NEW PROJECT FILE 4-2

4.2 ADDING PANEL INFORMATION 4-2

4.3 ADJUSTING THE NUMBER OF ZONE DISPLAYS 4-3

4.4 ADDING THE AZF LOGIC 4-3

4.5 WHERE TO NEXT? 4-3

5ADDING ADDRESSABLE DEVICES 5-1

5.1 ADDING DEVICES TO AN SPS ADDRESSABLE LOOP 5-2

5.2 ASSIGNING DEVICES TO ZONES 5-4

6ADDRESSABLE DEVICE SETTINGS 6-1

6.1 INTRODUCTION 6-2

6.1.1 ALARM DEVICE TYPES 6-2

6.2 ADDRESSABLE DETECTOR SETTINGS 6-2

6.2.1 4098-9714E PHOTO DETECTOR 6-2

6.2.2 4098-9717E ION DETECTOR 6-2

6.2.3 4098-9733E HEAT DETECTOR 6-2

6.2.4 4098-9754E MULTI-SENSOR PHOTO HEAT DETECTOR (COMBO) 6-3

6.3 ADDRESSABLE DEVICE SETTINGS 6-3

6.3.1 4099-9032 MCP 6-3

6.3.2 4090-9001 SUPERVISED INPUT IAM AND 4090-9051 ENCAPSULATED

INPUT IAM 6-4

6.3.3 4090-9002 RELAY IAM 6-4

6.3.4 4090-9101 MONITOR ZAM 6-4

6.3.5 4190-9050 4-20MA ANALOG MONITOR ZAM 6-4

Document: LT0400 4100U-S1 Programming Guide

Issue 1.4 15 December 2010 Page v

6.3.6 4090-9118 RELAY IAM WITH T-SENSE INPUT 6-4

6.3.7 4090-9119 RELAY IAM WITH UNSUPERVISED INPUT 6-5

6.3.8 4090-9120AU 6 POINT I/O MODULE (4 INPUTS, 2 RELAY OUTPUTS) 6-5

6.3.9 4090-9116 ADDRESSABLE IDNET ISOLATOR 6-6

6.3.10 4090-9117AU ADDRESSABLE IDNET POWER ISOLATOR 6-6

6.4 IDNET DEVICES TYPICAL APPLICATIONS 6-7

7ADDING ZONE DISPLAYS 7-1

7.1 GENERAL 7-2

7.2 ZONE CONTROL AND LED MODULES 7-2

7.3 HARDWARE CONFIGURATION MODIFICATION 7-2

7.4 MODIFY THE CUSTOM CONTROL EQUATIONS FOR THE ZONES 7-6

8ADDING EXPANSION MODULES 8-1

8.1 GENERAL 8-2

8.2 ADDING 4100-3101 IDNET LOOP CARD 8-2

8.3 ADDING 4100-4321 LEGACY SIGNAL CARD 8-5

8.4 ADDING 4100-5004 8 POINT MONITOR CARD. 8-7

8.5 ADDING 4100-3003 8 AUX RELAY CARD. 8-8

8.6 ADDING 4100-0302/1290 24 POINT GRAPHIC INTERFACE. 8-9

8.7 ADDING LEGACY CARD –4100-0113 RS-232/2120 INTERFACE MODULE 8-10

8.7.1 TYPICAL PRINTER CONFIGURATION: 8-11

9CUSTOM CONTROL 9-1

9.1 GENERAL 9-2

9.2 CUSTOM CONTROL SYNTAX 9-2

9.3 CREATING A NEW EQUATION 9-4

9.3.1 SELECT USER PROGRAM 9-4

9.3.2 ADD INPUT STATEMENTS 9-5

9.3.3 ADD OUTPUT STATEMENTS 9-6

9.3.4 OUTPUT STATEMENTS: HOLD VS. TRACK 9-7

10AS1668 FAN CONTROLS 10-1

10.1 TYPICAL ARRANGEMENT FOR AS1668 FAN CONTROL 10-2

10.2 AS1668 FAN CONTROL FLOWS 10-3

10.3 AS1668 FAN CONTROL STATE TABLE 10-5

10.4 AS1668 FAN CONTROL CARD PROGRAMMING 10-6

10.4.1 SWITCH CONFIGURATION 10-6

10.4.2 LED CONFIGURATION 10-7

10.4.3 POINT EDITING 10-8

10.5 AS1668 CUSTOM CONTROL EQUATIONS 10-9

10.5.1 FAN FAULT AND S/A RESTART DELAYS-STARTUP 10-9

10.5.2 SET UP REGISTER 8 10-10

10.5.3 S/A DETECTOR ISOLATE 10-10

10.5.4 S/A DETECTOR DE-ISOLATE 10-10

10.5.5 S/A DETECTOR ACTIVE 10-11

10.5.6 TRIGGER FAN ON 10-11

10.5.7 TRIGGER FAN OFF 10-11

10.5.8 FAN FAULT CONDITIONS 10-12

4100U-S1 Programming Guide Document: LT0400

Page vi 15 December 2010 Issue 1.4

11BUILDING AND DOWNLOADING THE CONFIGURATION 11-1

11.1 GENERAL 11-2

11.2 STARTING THE TRANSFER UTILITY 11-3

11.3 SERIAL COMMUNICATION PARAMETER SETTINGS 11-3

11.4 DIRECT CONNECTION TO THE PANEL 11-4

11.5 DOWNLOADING THE CFIG FILE 11-4

11.6 UPLOADING FROM THE PANEL 11-5

11.7 SENDING 4100U FILES TO SIMPLEX. 11-6

12APPENDICES 12-1

12.1 APPENDIX A –AS4428.1 OPERATION 12-2

12.2 APPENDIX B - COMMON VARIABLES AND CUSTOM CONTROL 12-3

12.2.1 DIGITAL PSEUDO POINTS 12-3

12.2.2 ANALOG POINTS 12-4

12.2.3 LISTS 12-4

12.2.4 PHYSICAL HARDWARE POINTS (LEDS RELAYS ETC) 12-4

12.2.5 BATTERY TEST 12-5

12.2.6 ALARM VERIFICATION TIMING AND START UP SETTINGS 12-5

12.2.7 BRIGADE RELAY EQUATIONS 12-6

12.3 APPENDIX C - CUSTOM CONTROL FOR CONTROL KEYS AND INDICATORS 12-8

12.3.1 COMMON ZONE ALARM LED 12-9

12.3.2 ALARM / FAULT / NORMAL TEST BUTTON AND LEDS 12-10

12.3.3 EXAMPLE ALARM AND FAULT TEST EQUATIONS 12-12

12.3.4 A/C RESET BUTTON AND A/C TRIP LED 12-12

12.3.5 BELLS ISOLATE LED AND BUTTON 12-13

12.3.6 WARNING SYSTEM ISOLATE 12-14

12.3.7 CLEAN UP EQUATIONS 12-14

12.4 APPENDIX D - CUSTOM CONTROL FOR ALARM ZONE FACILITIES 12-16

12.4.1 DIGITAL POINTS USED 12-16

12.4.2 LISTS 12-17

12.4.3 SWITCHES AND LEDS 12-17

12.4.4 ZONE 1 EQUATIONS 12-17

12.4.5 ZONE N EQUATIONS 12-18

12.5 APPENDIX E - 4100-1282 AZF SWITCH AND LED ADDRESS MAPPING 12-20

12.6 APPENDIX F –USEFUL PSEUDO POINTS AND LISTS 12-22

Document: LT0400 4100U-S1 Programming Guide

System Overview

Issue 1.4 15 December 2010 Page 1-1

1 Introduction

4100U-S1 Programming Guide Document: LT0400

System Overview

Page 1-2 15 December 2010 Issue 1.4

1.1 About this Manual

This manual provides information for creating and maintaining configuration files that contain

site-specific information for 4100U-S1 installations, based on standardized templates.

This manual does not cover how to install or configure hardware items. Refer to LT0394

4100U-S1 Installation and Maintenance Manual for details about this.

This manual does not cover configuration of networked 4100U-S1 systems. Contact your

local Simplex office/dealer for assistance with this.

The manual is divided into the following chapters:

Chapter 2 describes the 4100U-S1 system hardware and how this affects the

configuration procedure.

Chapter 3 describes the 4100U programming tools used for creating and updating

the configuration for a 4100U-S1.

Chapter 4 details the procedure for creating a configuration file for a new 4100U-S1

installation, using the configuration templates.

Chapter 5 describes how to add addressable devices to the configuration for the in-

built IDNet loop.

Chapter 6 details the configuration settings for addressable devices and how these

affect the operation of the devices.

Chapter 7 describes how to add zone display modules for more zones to the

configuration. This is for when an existing system is being extended to have more

zones.

Chapter 8 describes how to add expansion modules such as a second IDNet loop to

the configuration. This will apply to a new system which has additional modules over

the basic 4100U-S1, or to an existing 4100U-S1 installation that is being extended.

Chapter 9 describes how custom control equations are written and entered. Some

examples are given.

Chapter 10 describes how to configure the panel to control AS1668 Fans.

Chapter 11 describes how to build the configuration and download it to the panel.

Chapter 12 contains appendices which describe how AS4428.1 operation is

produced in 4100U-S1 using Custom Control equations. This is for reference only,

and is not required reading for normal configuration work.

Appendix A –a general description of AS4428.1 requirements.

Appendix B –describes the allocation of internal system resources and custom

control for system-wide functions.

Appendix C –describes custom control for control key and indicator operation on the

keyboard.

Appendix D –describes custom control for Alarm Zone Facility operation.

Document: LT0400 4100U-S1 Programming Guide

System Overview

Issue 1.4 15 December 2010 Page 1-3

Appendix E –describes 4100-1282 AZF Switch and LED Address mapping.

Appendix F –describes useful pseudo points and lists for when working on a 4100U

panel, especially when chasing intermittent faults.

1.2 Before you start

To get the job done with the minimum of problems and re-work, get the project specific data

sent to you via email or in writing –this helps keep track of the project details and changes.

You will need the cards and addressable loop/s details, including the devices types,

description/label and zoning. If there are zoned output trips, they should be defined via a

“cause and effect” matrix. Microsoft Excel or similar is very good for this purpose.

The most variable programming details are related to sprinkler flowswitch functionality and

AS1668 Fan and Damper control. Get the requirements resolved as soon as possible,

otherwise you may need to partially re-program so the required functionality is met.

Flowswitches may require:

Delayed activation –if so, how long is the delay?

Latching or non-latching operation.

ANDing with a Sprinkler Pressure Switch –to reduce unwanted alarms.

Which outputs will be tripped and are the outputs to latch?

AS1668 operation depends on the Mechanical Services Board/s and their functionality.

In some cases, general trip and zone trips are all that is required, with the Mech Board

starting and stopping the correct fans. In other cases, full start and stop control for smoke

management (with the manual controls in Auto position) is required by the panel.

Will fan operations be limited to manual Start/Stop control?

Will some fans be required to start (or stop) on any alarm –e.g. stair pressurization fans.

Will some fans be required to start (or stop) on specific zones in alarm –e.g. sandwich

Pressurization/smoke management?

Note: Dampers are programmed the same as exhaust fans.

The actual programming consists of four stages:

1. Adding/editing cards and addressable devices.

2. Adding the detection devices into pre-defined lists.

3. Adding/editing custom control, panel LEDs and switches mapping.

4. Build and download.

Follow the above sequence and the instructions in this guide - the programming will be

straight forward, especially if the templates are used to start the project file.

4100U-S1 Programming Guide Document: LT0400

System Overview

Page 1-4 15 December 2010 Issue 1.4

THIS PAGE IS INTENTIONALLY BLANK

Inhaltsverzeichnis

Andere Simplex Bedienfeld Handbücher

Simplex

Simplex 4007ES Panels Bedienungsanleitung

Simplex

Simplex SafeLINC 4100U Bedienungsanleitung

Simplex

Simplex 4100 Series Bedienungsanleitung

Simplex

Simplex 4100-9401 Programmierhandbuch

Simplex

Simplex MINIPLEX 4100ES Series Bedienungsanleitung

Simplex

Simplex 4010 Bedienungsanleitung

Simplex

Simplex 4006-9121 Bedienungsanleitung

Simplex

Simplex MINIPLEX 4100ES Series Bedienungsanleitung

Simplex

Simplex MINIPLEX 4100ES Series Bedienungs- und Wartungshandbuch

Simplex

Simplex SafeLINC 4100U Bedienungsanleitung

Simplex

Simplex 4100ESi Handbuch

Simplex

Simplex MINIPLEX 4100ES Series Bedienungsanleitung

Simplex

Simplex MINIPLEX 4100ES Series Bedienungsanleitung

Simplex

Simplex TrueAlarm 4008- 9121 Bedienungsanleitung

Simplex

Simplex SafeLINC 4100U Bedienungsanleitung

Simplex

Simplex MINIPLEX 4100ES Series Bedienungsanleitung

Simplex

Simplex 4010ES Bedienungsanleitung

Simplex

Simplex 4003 Bedienungsanleitung

Simplex

Simplex 4007-9201BA Bedienungsanleitung

Simplex

Simplex SafeLINC 4020 Bedienungsanleitung

Simplex

Simplex 4100ES-S1 Betriebsanleitung

Simplex

Simplex MINIPLEX 4100ES Series Bedienungsanleitung

Simplex

Simplex MINIPLEX 4100ES Series Bedienungsanleitung

Simplex

Simplex 4010 Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten