Simplex 4100U-S1 Bedienungsanleitung

4100U

Fire Alarm

FIRE

Operator's

Manual

SP1 Fire Indicator Panel

Operator’s Manual

4100U-S1 Fire Indicator

Operator’s

Manual

LT0395

Iss 1.0

Operator’s Manual

4100U-S1 Fire Panel Operator’s Guide

Fire detectors in the building are grouped into zones (searchable areas).

Zones can be Isolated by pressing the zone’s isolate pushbutton on the panel – this prevents an

alarm from activating the panel outputs.

When a non-isolated detector detects an alarm, the fire panel rings the bell, calls the fire brigade,

activates the Warning or Evacuation System and any other programmed functions.

The Fire Panel display consists of two sections – the Operator Interface (upper section) and the

Zone Isolate pushbutton switches & indicators (lower section).

The Operator Interface indicates common Alarm, Fault & Isolation Status on LEDs, and point

(detector) status on the LCD.

When an Alarm, Fault or Isolation occurs, the buzzer will operate until the corresponding

acknowledge (Ack) key is pressed.

The panel is reset by pressing SYSTEM RESET. If the alarm won’t reset the point may still be

activated. Press FIRE ALARM ACK when the point alarm is displayed, then press DISABLE, ENTER.

Press FAULT ACK (to acknowledge the fault caused by disabling a point), then press SYSTEM RESET

again. The disabled detector must be re-enabled when the condition is cleared.

Silence the Bell: Press the EXT BELL ISOLATE key.

Isolate signals to Evacuation System: Press the

WARN SYS ISOLATE key. This will turn off warning

sounders powered by the Fire Panel.

Isolate a Zone: Press the appropriate Zone Isolate

pushbutton and the Zone Isolated LED will turn on.

Acknowledge an Isolation: Press the ISOLATE ACK

key.

Acknowledge an Alarm: Press the FIRE ALARM ACK

key.

Acknowledge a Fault: Press the FAULT ACK key. Zone Isolate

Pushbuttons

Operator Interface

Australian Standard AS 4428.1, Control and Indicating Equipment. SSL Listing No. afp1682

The 4100U-S1 is manufactured by Tyco Safety Products for : Tyco Services, Fire & Safety

47GilbyRoad

Notting Hill

VIC 3168

AUSTRALIA

All specifications and other information shown were current as of document revision date, and are

subject to change without notice.

Tyco, Simplex, the Simplex logo, MAPNET II, IDNet, TrueAlarm, SmartSync, WALKTEST,

MINIPLEX, and TrueAlert are trademarks of Tyco International Services AG or its affiliates in the U.S.

and/or other countries. VESDA is a trademark of Vision Products Pty Ltd.

Simplex fire alarm technology is protected by the following U.S. Patent Numbers:

TrueAlarm analog smoke detection: 5,155,468; 5,173,683 and 5,543,777. IDNet and

MAPNET II addressable communications; 4,796,025. TrueAlert addressable notification;

6,313,744 and 6,426,697. SmartSync horn/strobe control; 6,281,789.

No part of this document may be reproduced or transmitted in any form or by any means, electronic

or mechanical, for any purpose, without the express written consent of Tyco Safety Products.

Document Number : LT0395

Cross Reference : 579-197

Issue : 1.0 13 February 2006

11.10

23 March 2006 LT0395 Issue 1.0 Original based on LT0351 1.0-C

Manufacturer’s Details

Approvals

Manufacturer

Trademark

Information

Document

Firmware

Revision

Amendments

iii

If installed as per the Installation Manual this product complies with Class B limits of AS/NZS 3548.

4100U-S1 Panel Supplied by:

Installation Location

Contract/Job Number

As installed, FIP System Drawing Number

Panel Installation Date

Panel Commissioned Date

Weekly Battery Test Day & Time

Maintenance Company

Telephone

Service Contract

Some of the operation of the 4100U-S1, as described in this manual, is dependent on

custom configuration as performed by the field engineer. If the configuration is not as per

the recommended template, then operation may differ and compliance to AS4428.0 may

be invalid.

The 4100U-S1 has a facility to allow levels of passcode protection. The operation of all the

standard functions as described in this manual is to be programmed to not require entry of

a passcode.

ZONE ISOLATIONS - The zone isolate status is not stored in non-volatile memory, so if the panel

is powered down and back up, or if the CPU is reset, all zones will be de-isolated.

Product/Site

Cautions &

Warnings

Approvals.....................................................................................................................ii

Manufacturer................................................................................................................ii

Document ....................................................................................................................ii

Firmware Revision.......................................................................................................ii

Amendments................................................................................................................ii

Product/Site................................................................................................................ iii

Cautions & Warnings.................................................................................................. iii

Chapter 1 Overview.........................................................................1-1

Introduction...............................................................................................................1-1

In this Chapter ..........................................................................................................1-1

Typical Panel Layout..............................................................................................1-2

Overview...................................................................................................................1-2

Basic System Description......................................................................................1-3

Overview...................................................................................................................1-3

Control Keys & Indicators......................................................................................1-6

Overview...................................................................................................................1-6

Control Keys & Indicator Functions..........................................................................1-6

Normal Appearance of Operator Interface...........................................................1-7

Description................................................................................................................1-7

Chapter 2 Managing Alarm Conditions.........................................2-1

Introduction...............................................................................................................2-1

In this Chapter ..........................................................................................................2-1

Acknowledging Alarms..........................................................................................2-2

What the System Does When an Alarm Occurs ......................................................2-2

Overview – Acknowledging Alarms..........................................................................2-2

Procedure.................................................................................................................2-3

Isolating (Silencing) the EWS or External Bell ....................................................2-4

Overview...................................................................................................................2-4

Isolating the EWS.....................................................................................................2-4

Isolating the External Bell.........................................................................................2-4

Isolating the Zone.....................................................................................................2-4

Isolating ACF Outputs............................................................................................2-5

Overview...................................................................................................................2-5

Operation..................................................................................................................2-5

Restoration ...............................................................................................................2-5

Resetting Air Conditioning Control ......................................................................2-6

Overview...................................................................................................................2-6

Indication ..................................................................................................................2-6

Resetting...................................................................................................................2-6

Displaying Event time ............................................................................................2-7

Procedure.................................................................................................................2-7

Resetting Points .....................................................................................................2-8

Overview...................................................................................................................2-8

Reset Procedure.......................................................................................................2-8

Chapter 3 Managing Fault and Isolate Conditions.......................3-1

Introduction...............................................................................................................3-1

In this Chapter ..........................................................................................................3-1

Acknowledging Fault or Isolate Conditions.........................................................3-2

How the 4100U-S1 Indicates the Presence of a Fault .............................................3-2

What Acknowledge Does .........................................................................................3-2

Panel Operating Procedure – Fault Condition..........................................................3-3

Resetting Fault Conditions .......................................................................................3-3

Viewing Fault or Isolate Conditions......................................................................3-4

Overview...................................................................................................................3-4

Chapter 4 Testing and Controlling Points.....................................4-1

Introduction...............................................................................................................4-1

In this Chapter ..........................................................................................................4-1

Table of Contents

Alarm and Fault Test for Zones.............................................................................4-2

Alarm Test ................................................................................................................4-2

Fault Test..................................................................................................................4-2

Isolating and De-isolating Zones ..........................................................................4-3

Overview...................................................................................................................4-3

Isolating a Zone........................................................................................................4-3

De-Isolating a Zone..................................................................................................4-3

Disabling and Enabling Points..............................................................................4-4

Overview...................................................................................................................4-4

Disabling a point.......................................................................................................4-4

Enabling a point........................................................................................................4-4

Turning a Point ON or OFF....................................................................................4-5

Overview...................................................................................................................4-5

Turning a Point OFF.................................................................................................4-5

Turning a Point ON...................................................................................................4-5

Returning a Point to Automatic Operation................................................................4-5

Sounder (buzzer)......................................................................................................4-5

Chapter 5 Selecting Points for Status or Control.........................5-1

Introduction...............................................................................................................5-1

In this Chapter ..........................................................................................................5-1

Selecting Points from the Menu............................................................................5-2

Overview...................................................................................................................5-2

Procedure.................................................................................................................5-2

Selecting Points with the Entry Keypad...............................................................5-3

Overview...................................................................................................................5-3

Selecting Points........................................................................................................5-3

Chapter 6 Displaying and Modifying Detailed Point Attributes..6-1

Introduction...............................................................................................................6-1

In this Chapter ..........................................................................................................6-1

Display-Only Attributes..........................................................................................6-2

Select a Point............................................................................................................6-2

See the Attributes.....................................................................................................6-2

Summary of Display-Only Attributes.........................................................................6-2

Modifiable Point Attributes....................................................................................6-4

Overview...................................................................................................................6-4

Select a Point............................................................................................................6-4

See the Attributes.....................................................................................................6-4

Summary of Modifiable Attributes.............................................................................6-4

Chapter 7 Setting Access Levels and Logging In ........................7-1

Introduction...............................................................................................................7-1

In this Chapter ..........................................................................................................7-1

Operator Access Levels.........................................................................................7-2

Overview...................................................................................................................7-2

Logging In and Out of the System........................................................................7-3

Introduction...............................................................................................................7-3

Log In Procedure......................................................................................................7-3

Log Out Procedure ...................................................................................................7-4

Chapter 8 Viewing and Clearing Historical Logs..........................8-1

Introduction...............................................................................................................8-1

In this Chapter ..........................................................................................................8-1

Viewing and Clearing the Historical Alarm and Fault Logs ...............................8-2

Viewing Logs ............................................................................................................8-2

Clearing the Logs......................................................................................................8-2

Chapter 9 Service-Related Operations..........................................9-1

Introduction...............................................................................................................9-1

In this Chapter ..........................................................................................................9-1

Setting Time and Date............................................................................................9-2

Procedure.................................................................................................................9-2

Displaying Software Revision ...............................................................................9-3

Overview...................................................................................................................9-3

Viewing Card Status Information..........................................................................9-4

Overview...................................................................................................................9-4

Procedure.................................................................................................................9-4

Power Supply/Charger Voltage and Current Readings............................................9-4

Displaying Network Node Information .................................................................9-5

Overview...................................................................................................................9-5

Procedure.................................................................................................................9-5

Lamp Test................................................................................................................9-6

Procedure.................................................................................................................9-6

Displaying IDNet & Mapnet Device Status...........................................................9-7

Introduction...............................................................................................................9-7

IDNet Display Information.........................................................................................9-7

IDNet Point Addressing............................................................................................9-7

How to Display an IDNet System Point....................................................................9-7

What To Do If an IDNet Point Will Not Reset...........................................................9-7

TrueAlarm Sensor Display Values............................................................................9-7

Chapter 10 System Test Procedures...........................................10-1

Introduction.............................................................................................................10-1

In this Chapter ........................................................................................................10-1

Walk Test™ ...........................................................................................................10-2

Overview.................................................................................................................10-2

WalkTest™by Group..............................................................................................10-2

Zone Coding Option ...............................................................................................10-2

Silent Walk Test......................................................................................................10-3

Enabling Walk Test.................................................................................................10-3

Walk Test Operation...............................................................................................10-4

Walk Test™ FEATURES.......................................................................................10-5

Introduction.............................................................................................................10-5

Abort Audible and Delay on Reactivation...............................................................10-5

Active/Not Active.....................................................................................................10-5

Auto Abort on Alarm...............................................................................................10-5

Auto Abort on Time-Out..........................................................................................10-5

Control List..............................................................................................................10-5

Delay Before Reset ................................................................................................10-6

Logging Option (Log/No Log).................................................................................10-6

Monitor Zone List....................................................................................................10-6

Programmer Configuration.....................................................................................10-6

Sig/No Sig (Silent Walk Test™ Selection)..............................................................10-6

System Fault...........................................................................................................10-6

Fault Audible...........................................................................................................10-7

Zone Code/Zero Code............................................................................................10-7

Walk Test™ PROCEDURES.................................................................................10-8

How to Enter Walk Test Mode...............................................................................10-8

How to Exit Walk Test Mode ..................................................................................10-9

How to Turn a Point Off........................................................................................10-10

How to Turn a Point On........................................................................................10-10

How to Return a Point to Auto..............................................................................10-11

How to Enable a Disabled Point...........................................................................10-12

What to do in Case of System Malfunction ..........................................................10-13

Chapter 11 Printing Reports.........................................................11-1

Introduction.............................................................................................................11-1

In this Chapter ........................................................................................................11-1

Setting Printer Options ........................................................................................11-2

Available Options....................................................................................................11-2

Printing a Report...................................................................................................11-3

Overview.................................................................................................................11-3

Procedure...............................................................................................................11-3

Chapter 12 Maintenance Procedures ..........................................12-1

Introduction.............................................................................................................12-1

vii

In this Chapter ........................................................................................................12-1

Weekly Tests.........................................................................................................12-2

Procedure...............................................................................................................12-2

Battery Test ............................................................................................................12-2

Monthly Tests........................................................................................................12-3

Procedure...............................................................................................................12-3

Annual Tests .........................................................................................................12-4

Procedure...............................................................................................................12-4

viii

Andere Handbücher für 4100U-S1

Inhaltsverzeichnis

Andere Simplex Feuerlöschausrüstung Handbücher

Simplex

Simplex FUELPORT FP-X Bedienungsanleitung

Beliebte Feuerlöschausrüstung Handbücher anderer Marken

Tyco Fire Protection Products

Tyco Fire Protection Products AM31 AQUAMIST Nozzle Bedienungsanleitung

Task Force Tips

Task Force Tips Extend-A-Gun RC3 Betriebsanleitung

Autronica

Autronica AutroSafe BSD-321/EX Bedienungsanleitung

POK

POK Froggy Bedienungsanleitung

Waterous

Waterous AQUIS Series Handbuch

CTP

CTP NPO ETERNIS GUARANT-7 Stücklistenhandbuch

MSA

MSA M1 Bedienungsanleitung

Grundfos

Grundfos Hydro EN Betriebsanleitung

Amerex

Amerex 570 Anwendungshandbuch

Vimpex

Vimpex BIG HP18-H200-B1 Bedienungsanleitung

Global Fire Equipment

Global Fire Equipment GFE-PA-VOX-A Bedienungsanleitung

Chubb

Chubb PEFS F3 Bedienungsanleitung

Projoy Electric

Projoy Electric PEFS-PL Series Bedienungsanleitung

klimaoprema

klimaoprema FDC25 Series Bedienungsanleitung

Tyco

Tyco 802SB Bedienungsanleitung

Mueller

Mueller Revive M2 Bedienungsanleitung

SEI Industries

SEI Industries BAMBI MAX BBXHL4000PF Bedienungsanleitung

Waterax

Waterax MARK-3 Bedienungsanleitung