Simplex 4605 Bedienungsanleitung

4605 24-Point I/O Card

Installation Instructions

1998 Simplex Time Recorder Co., Gardner, MA 01441-0001 USA

All specifications and other information shown were current as of publication, and are subject to change without notice 574-348

Rev. B

DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS

DAMAGED. Upon unpacking your Simplex product, inspect the contents of the

carton for shipping damage. If damage is apparent, immediately file a claim

with the carrier and notify Simplex.

ELECTRICAL HAZARD - Disconnect electrical power when making any

internal adjustments or repairs. Servicing should be performed by qualified

Simplex Representatives.

STATIC HAZARD - Static electricity can damage components. Therefore,

handle as follows:

1. Ground yourself before opening or installing components (use the 553-484

Static Control Kit).

2. Keep uninstalled component wrapped in anti-static material at all times.

RADIO FREQUENCY ENERGY - This equipment generates, uses, and can

radiate radio frequency energy and if not installed and used in accordance with

the instruction manual, may cause interference to radio communications. It has

been tested and found to comply with the limits for a Class A computing device

pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide

reasonable protection against such interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause

interference in which case the user at his own expense will be required to take

whatever measures may be required to correct the interference.

This publication shows how to install the 4605 24-Point I/O card with a 4010

Fire Alarm Control Panel (FACP). A maximum of six of these option cards is

allowed per system. Refer to the 4010 Fire Alarm - Installing, Operating, and

Programming Instructions (574-052) for configuration information. Refer to the

842-063 Field Wiring Diagram for additional wiring information.

This publication discusses the following topics:

Topic See Page #

Overview 1

4605 24-Point I/O Card 2

Configuration 3

Wiring 4

Card Installation 5

Cautions and Warnings

Overview

In this Publication

firealarmresources.com

The 4605 24 Point I/O Card is a “slave” card that communicates to the 4010

FACP. The 24 Point I/O Card for the 4010 is capable of using any combination of

24 inputs or outputs to control LEDs, lamps, relays, and contact closure inputs.

The outputs can be on continuous or flashed, at a slow or fast rate. The inputs may

be unsupervised, supervised for opens, supervised for open and shorts, or

H.O.A.(Hand Off Auto) switches, depending upon how the switch is wired

externally (for complete wiring instructions, refer to the 842-063 Field Wiring

Diagram). The inputs and outputs must be provided by a listed (signaling device)

annunciator.

Figure 1 shows the location of the connectors and switches on the 4605 I/O

Card.

REMOTE

PWR

+++C

24C

+24V

1RET

2RET

SHLD

++--

N2 COMM

TB5 TB2 TB3 TB1

TB4

SW1

SW2

ADDRESS

DR1 DR2 DR3 DR4 DR5 DR6 DR7 DR8 DR9 DR10 DR11 DR12 DR13 DR14 DR15 DR16 DR17 DR18 DR19 DR20 DR22DR21 DR23 DR24

226

I/O

Figure 1. 4605 24-Point I/O Card Switches and Connectors

4605 24-Point I/O Card

Overview

firealarmresources.com

Card Address Setting (SW1)

Option cards in the 4010 system have specific addresses. The range of card

addresses setting for the 24-Point I/O card is Cards 9 through 14. Use Table 1 to

set SW1 to the appropriate address.

Table 1. SW1 Address Switch Settings

Card Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 thru SW1-8

9 ON OFF OFF ON OFF

10 OFF ON OFF ON OFF

11 ON ON OFF ON OFF

12 OFF OFF ON ON OFF

13 ON OFF ON ON OFF

14 OFF ON ON ON OFF

Use the “Quick CFIG - Add NEW Hardware” function described in the 4010

Fire Alarm - Installation/Operation Instructions (574-052) to add the card to the

system.

Baud Rate Setting (SW2)

N2 Communications on option cards must be set at the same baud rate as the

4010 FACP. The 24-Point I/O card’s baud rates are set from SW2. Use the

information in Table 2 to set SW2 to the appropriate baud rate. The default

setting should be 9600.

Table 2. SW2 Baud Rate Settings

Baud Rate SW2-1 SW2-2

OFF-Line ON ON

9600 OFF ON

19200 ON OFF

38400 OFF OFF

Configuration

Switch Settings

firealarmresources.com

Use Figure 2 and the notes below to wire the 24-Point I/O card.

REMOTE

PWR

+++C

24C

+24V

1RET

2RET

SHLD

++--

N2 COMM

TB5 TB2 TB3 TB1

TB4

SW1

SW2

ADDRESS

DR1 DR2 DR3 DR4 DR5 DR6 DR7 DR8 DR9 DR10 DR11 DR12 DR13 DR14 DR15 DR16 DR17 DR18 DR19 DR20 DR22DR21 DR23 DR24

226

I/O

TYPICAL LED

OUTPUT

TYPICAL LAMP

OUTPUT

Figure 2. 24-Point I/O Wiring

Wiring

24-Point I/O Wiring

24V (C)

24V (+)

Remote Power (C)

Remote Power (+)

See Notes 3 and 11

N2 Comm (-)

N2 Comm (+) See Note 7

See Note 4

See Note 10

Notes:

1. All wiring to be 18AWG minimum or to local

code.

2. Conductors must test free of all grounds.

3. Voltage input 18.9VDC min. to 32VDC max.

4. Maximum current is 75mA per output.

5. Drawing depicts typical wiring. All output

zones may not be wired. Supervision for the

unused inputs are by-passed in software.

6. Wiring is supervised and Power-Limited.

7. For N2 Comms wired in a “bus” fashion, the

maximum line distance is 4000 ft. For N2

Comms wired in a T-Tapped configuration,

the maximum distance to any N2 device is

2500 ft, with maximum total wire distance

not to exceed 10,000 ft on the T-tapped lines.

If the 24 Point I/O is the last device on the N2

bus (Non-T-Tapped), or the furthest device

(T-Tapped) terminate across N2+ and N2-

using a 733-974 (100

, 1/2W) resistor

harness.

8. Total current = 60mA base controller current.

Add current for each output used.

9. Wiring to I/O terminals must not be run with

AC wiring.

10. Alternate Ribbon Cable for TB4:

TB4-1 P2-1 TB4-13 P2-13

TB4-2 P2-2 TB4-14 P2-14

TB4-3 P2-3 TB4-15 P2-15

TB4-4 P2-4 TB4-16 P2-16

TB4-5 P2-5 TB4-17 P2-17

TB4-6 P2-6 TB4-18 P2-18

TB4-7 P2-7 TB4-19 P2-19

TB4-8 P2-8 TB4-20 P2-20

TB4-9 P2-9 TB4-21 P2-21

TB4-10 P2-10 TB4-23 P2-22

TB4-11 P2-11 TB4-23 P2-23

TB4-12 P2-12 TB4-24 P2-24

11. Allowable power supplies: 4010-9101, -9102,

-9201, -9202, -9813, and -9814 or any

regulated Power-Limited supply that is UL

Listed for Fire Protective Signal Use.

firealarmresources.com

Install the 4605-8402 mounting bracket (supplied) into the electrical back box

(supplied by others). When mounting the bracket, be careful not to pinch any

wiring behind the bracket. The bracket is designed to hold up to six 24-Point

I/O cards.

Select a position for the 24-Point I/O card on the mounting bracket and install

the card using the stand-offs and screws provided.

IMPORTANT: Pay careful attention to the routing for Power-

Limited and Non-Power Limited wiring. You must

maintain a 1/4-inch separation between these two

types of wiring. Neatly dress all harnesses and

wiring.

Neatly dress all harnesses and wiring and then apply power.

Card Installation

Mounting Bracket

Installing the 24-Point I/O

Card

4605 24-Point I/O Card

Mounting Bracket

firealarmresources.com

574-348

Rev. B

firealarmresources.com

Inhaltsverzeichnis

Andere Simplex E/A-System Handbücher

Simplex

Simplex IDNet 4010 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung