3
Adapter
Bolts
Rotating Hub
Adapter
Plate
Hub Bolts
& Washers
Base Plate
S T E P 1 Adapter Plate
Locate adapter plate and place in desired location on the deck. The adapter plate should
overlap two deck planks evenly. Adjust the base plate so that the proper alignment is
ensured.
S T E P 2 Drilling Deck Planks
ark the four countersunk holes onto the deck for drilling. Drill four 10mm holes through
the deck planks for the round countersunk bolts. Remove enough deck screws or nails
from these planks to be able to install base plate underneath the planks.
S T E P 3 Attach Base and Adapter Plates to Deck Planks
Attach the base plate and adapter plate together, with the base plate under the deck and
the adapter plate on top of the deck planks, using four (4) round countersunk bolts (Note:
If deck is thicker, longer bolts will be required. A contractor can help determine appropriate
size bolts). Insert the (4) round countersunk downward through the top of the countersunk
holes on adapter plate, through the planks, and screw them into the threaded holes in the
bottom base plate. ake sure they are very tight.
S T E P 4 Fasten Deck Planks
Refasten the deck planks to the joists by attaching removed screws from Step 2 in the
original holes closest to the base plate. Two structural deck screws should be used on
either side of the base plate in each plank.
S T E P 5 Attach Rotating Hub to Adapter Plate
Attach rotating hub to adapter plate using the hub bolts and washers that came with your
umbrella.
S T E P 6 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual
for further assistance.
You are now ready to operate your umbrella!
RE OVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbrella Instruction anual for further assistance on how to
remove umbrella.
WOODEN DECK OUNT KIT
Wooden Deck ount Kit
includes:
A-Adapter Plate
B-Base Plate
C-Round Countersunk Bolts (4)
D-Allen Wrench
4
IN-GROUND OUNT KIT
S T E P 1 Preparation
The in-ground fitting should or can be
built into newly poured concrete. For a
perfect flush mount, set the plate of the
fitting 3/8” below the final surface grade.
When you add the 3/8” thick adapter
plate to the fitting plate, the adapter
plate will be flush with the concrete.
S T E P 2 Bolt Adapter Plate
Once installed and the concrete has
cured, bolt the adapter plate
(countersunk holes face up) to the top of
the in-ground fitting using the four (4)
stem bolts and allen wrench. Insert the
stem bolts downward through the
countersunk holes in the adapter plate
and screw them into the threaded holes
in the top of the in-ground fitting. ake
sure they are very tight.
S T E P 3 Attach Rotating Hub
Attach rotating hub to adapter plate using the hub bolts that came with your umbrella.
S T E P 4 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual
for further assistance.
You are now ready to operate your umbrella!
I PORTANT: When concreting the in-ground fitting in place, make sure not to get slurry
in the screw threads. Either apply tape over the holes on both sides of the fitting or place
the stem bolts in the threads and withdraw them when the concrete is set. ake sure that
the
in-ground fitting is perfectly level. Allow the concrete to cure for the appropriate cure time
for your area before installing the umbrella onto the fitting.
RE OVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbrella Instruction anual for further assistance on how to
remove umbrella.
C
B
Ground Level
Concrete Footing
Flare at
bottom
1.0m
or
3’4”
In-Ground
Fitting
AMK
Adapter Plate
Ground
Stem Bolts
Rotating Hub
Hub Bolts
& Washers
Hole Diameter
500mm or 21” - 24”
A
D
In-Ground Fitting Kit includes:
A-Adapter Plate (8.5” diameter) C-Stem Bolts (4)
B-In-Ground Fitting D-Allen Wrench
B
A
CD
