Simrad RF40 Bedienungsanleitung

| 1

RF40 Rudder Feedback unit

Installation guide

The RF40 is a resistive rudder feedback unit, suitable for autopilot systems with a

NAC-1 or NAC-2 autopilot computer.

¼Note: The RF40 can not be used with the NAC-3 autopilot computer.

The RF40 might also be used with autopilot computers that have analog rudder

feedback input.

¼Note: Do not remove the transmitter lever from the feedback unit.

¼Note: The unit is factory adjusted and requires no further adjustment at

installation than described below.

Mounting location

The RF40 unit (A) mounts close to the rudder, and is mechanically linked to the

rudder tiller arm (B) or rudder quadrant.

Select a mounting location for the RF40 unit according to the illustration

• X1 = X2: min 150 mm (5.9”), max 345 mm (13.6”)

• Y1 = Y2: min 44 mm (1.7”), max 130 mm (5.1”)

Y1 Y2

X1 = X2

Y1 = Y2

2 |

Installation

The RF40 lever (C) has two slots for the transmitter link (D). The slots enable

maximum exibility to provide the 1:1 mechanical linkage relationship.

Y1 Y2

1. Turn the helm to set the rudder tiller arm (B) to approximate center position

2. Mount the RF40 unit to a suitable platform

• If required:

-add blocking material under the RF40 to adjust the height of the

transmitter lever to be level with the rudder tiller arm

-cut the length of the transmitter rod (D) to move the feedback unit closer

to the rudder post

3. Rotate the RF40 lever to center position

• the marks (E) on unit and on the lever should be aligned

4. Rotate the RF40 unit so that the rudder lever is parallel with the rudder tiller arm

5. Set the transmitter link to the inner limit of the outer slot if possible

6. Drill and tap the rudder tiller arm so that the Y2 dimension is equal to the Y1

dimension

7. Attach the ball joint to the tiller arm, and connect the transmitter rod to the ball

joint at the rudder tiller arm

8. Tighten the mounting screws for both the RF40 and the transmitter rod ball

joint.

9. Observe the feedback unit while someone turns the helm through the complete

rudder travel hard-over to hard-over, and verify that the mechanical linkage

moves freely.

| 3

Wiring

The RF40 is equipped with a 15 m (49 feet) cable with connector (A). The unit

connects to the NAC-1/NAC-2 autopilot computer’s three pins rudder feedback

socket (B).

A B

1 2

Function Color

1+5 V DC Red

2Signal Yellow

3-0 V DC Black

Dimensional drawings

RF40

177 mm (6.97”)

55 mm

(2.16”)

99 mm (3.90”)

65 mm

(2.56”)

Transmitter link

345 mm (13.6”)

4 |

Spare part

20193454 Transmitter link

Technical specications

¼Note: The most up-to-date specications list is available at

www.simrad-yachting.com

Physical

Dimensions See gure

Weight 0.5 kg (1.1 lbs.)

Material Arnite T06 200 PBT

Compass safe distance 1.0 m (3.1 ft.)

Mounting Horizontal, vertical or upside down

Cable 15 m (49 feet) with connector

Transmitter link Stainless 345 mm (13.6”) with 2 ball joints

Electrical

Supply voltage 5 V DC

Power consumption 2.5 mW

Environmental

Operating temperature -25 to +55 °C (–13 to +130 °F)

Storage temperature -30 to +70 °C (–22 to + 158 °F)

Waterproof rating IP56

Interface

Rudder angle +/-120 degrees

Output signal 0 - 5 V DC

Resistance value 10 K ohms

Accuracy +/-0.25° within +/-5°, otherwise +/-0.5°

Repeatability +/-0.1°

*988-12045-001*

Inhaltsverzeichnis

Andere Simrad Schiffsausrüstung Handbücher

Simrad

Simrad NSO-II Bedienungsanleitung

Simrad

Simrad ME70 - REV C Bedienungsanleitung

Simrad

Simrad SD1 Bedienungs- und Wartungsanleitung

Simrad

Simrad ES60 - DATASHEET REV A Bedienungsanleitung

Simrad

Simrad NSS9 evo3S Bedienungsanleitung

Simrad

Simrad AI80 Bedienungsanleitung

Simrad

Simrad SN90 Bedienungsanleitung

Simrad

Simrad AP70 Bedienungsanleitung

Simrad

Simrad CS90 Bedienungsanleitung

Simrad

Simrad AP24 Bedienungsanleitung

Simrad

Simrad SimNet Kurzanleitung

Simrad

Simrad PI HBU - REV A Bedienungsanleitung

Simrad

Simrad SX90 - DATASHEET FOR NAVAL AND COAST GUARD REV... Bedienungsanleitung

Simrad

Simrad BSM-3 Bedienungsanleitung

Simrad

Simrad CE34 ChartSounder Bedienungsanleitung

Simrad

Simrad IS42J Bedienungsanleitung

Simrad

Simrad IS20 Wind Bedienungsanleitung

Simrad

Simrad B&G h2000 Bedienungsanleitung

Simrad

Simrad IS80 Heading Repeater HR80 Bedienungsanleitung

Simrad

Simrad NL - SPEED LOG REV C Bedienungsanleitung

Simrad

Simrad Navico WP10 Bedienungsanleitung

Simrad

Simrad ITI TRAWL SYSTEM - SERIAL DATA COMMUNICATION REV... Bedienungsanleitung

Simrad

Simrad IS42J Bedienungsanleitung

Simrad

Simrad MX610 Bedienungsanleitung

Beliebte Schiffsausrüstung Handbücher anderer Marken

Clarion

Clarion CMS2 Reparaturanleitung

EBS

EBS M7000 Bedienungsanleitung

Kongsberg

Kongsberg M3 Bathy Bedienungsanleitung

NPK

NPK SCS-1002 Bedienungsanleitung

Furuno

Furuno FE-800 Bedienungsanleitung

Harken

Harken 1561 Bedienungsanleitung

Notifier

Notifier FS-BSO Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

E2S

E2S E2XS112UL Bedienungsanleitung

R2Sonic

R2Sonic 2026 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6000 Bedienungsanleitung

Clarion

Clarion GR10BT Reparaturanleitung

Raymarine

Raymarine Maxiview ST80 Benutzerhandbuch

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Montageanleitung

Raymarine

Raymarine ST60 Tridata Benutzerhandbuch

olympia electronics

olympia electronics ΒS-531/1/MAR Bedienungsanleitung

Sonic

Sonic 2024 Bedienungsanleitung

Quicksilver

Quicksilver 88688A25 Handbuch