Singer MT624 Bedienungsanleitung

P a g e 1 of 8, V1

SuperbaKnit interface electronic hardware exchange for MT624 & 9000

The picture below shows the Singer MT624 knitting machine.

Place the bed on a table or workbench with the right end hanging free to give access to

the bottom.

P a g e 2 of 8, V1

Remove the screw that holds the small plastic cover piece

P a g e 3 of 8, V1

Slide the cover to the right and remove it completely.

P a g e 4 of 8, V1

After removal of the plastic cover, your machine will look similar to the picture

above.

P a g e 5 of 8, V1

Remove the printed circuit board from the connector.

P a g e 6 of 8, V1

The MT 624 after removal of the PCB.

Now you have to cut the red wire that comes from somewhere under the metal belt,

and runs either to the black connector, or disappears in the cable sleeve whit the

other 4 visible wires.

P a g e 7 of 8, V1

Make sure you do not cut a second red wire that runs from the connector into the

cable sleeve. If the red wire goes to the connector, cut the red wire close to the

connector. If the red wire goes into the cable sleeve, cut the red wire where the red

wire enters the cable sleeve. This gives the maximum length for this piece of wiring.

Then enter this lose end of red wire in the clamp connector. No need to remove

insulation. Put it right in the middle and then snap together the clamp. It usually

needs no tools, just your fingers, to close the clamp.

The result should look as above.

P a g e 8 of 8, V1

Attach the connector at the end on the header in the middle of the new pc board,

and insert the pc board into the black connector. Center the contacts well and make

sure the board is inserted to its maximum position.

It should look now as above.

Now you have to adjust the 2 potentiometers that control the optical sensor

sensitivity. For instructions, please consult the “SuperbaKnit Interface A

Adjustments” document.

Place back the plastic end cover of the bed just in the reversed way as you removed

the cover, and secure the cover with the screw from the bottom side.

Dieses Handbuch passt für folgende Modelle

1

Andere Singer Nähmaschine Handbücher

Singer

Singer 251-4 Bedienungsanleitung

Singer

Singer C7290Q Bedienungsanleitung

Singer

Singer Slant Needle Installations- und Betriebshandbuch

Singer

Singer 261U Gebrauchsanweisung

Singer

Singer CXL Bedienungsanleitung

Singer

Singer HD6360 Bedienungsanleitung

Singer

Singer 403A Bedienungsanleitung

Singer

Singer 71-101 Kurzanleitung

Singer

Singer 71-107 Kurzanleitung

Singer

Singer 1669U Bedienungsanleitung

Singer

Singer 7033 Bedienungsanleitung

Singer

Singer 1591D200A Einrichtungshandbuch

Singer

Singer 354 Bedienungsanleitung

Singer

Singer 2623 Bedienungsanleitung

Singer

Singer 212W146 Bedienungsanleitung

Singer

Singer 62-48 Bedienungsanleitung

Singer

Singer 348K Bedienungsanleitung

Singer

Singer 20U Bedienungsanleitung

Singer

Singer 222K Bedienungsanleitung

Singer

Singer 247-2 Bedienungsanleitung

Singer

Singer 591V Bedienungsanleitung

Singer

Singer 3820 Bedienungsanleitung

Singer

Singer 9030 Bedienungsanleitung

Singer

Singer FEATHERWEIGHT II 118 Bedienungsanleitung

Beliebte Nähmaschine Handbücher anderer Marken

Riccar

Riccar RL634DE Bedienungsanleitung

Pfaff

Pfaff 3307-1 SERIES Bedienungsanleitung

Janome

Janome Quilt Maker Pro 18 VERSA Bedienungsanleitung

Siruba

Siruba C007JP Bedienungsanleitung

Husqvarna Viking

Husqvarna Viking Designer SE Bedienungsanleitung

IKEA

IKEA SY Bedienungsanleitung

Pfaff

Pfaff 571 Bedienungsanleitung

Brother

Brother BB370 Bedienungsanleitung

Pegasus

Pegasus WT100 Series Bedienungsanleitung

Reliable

Reliable 7100DB Bedienungsanleitung

Pfaff

Pfaff 937 Bedienungsanleitung

Pfaff

Pfaff 1471 E1 Bedienungsanleitung

Kenmore

Kenmore 16677 - Serger Sewing Machine Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC2008-M Bedienungsanleitung

Brother

Brother BE-1204C Bedienungsanleitung

JUKI

JUKI MO-104 Bedienungsanleitung

Bernina

Bernina Quilting Frame Bedienungsanleitung

Brother

Brother 885-V14 Bedienungsanleitung