Singer TINY TAYLOR TT700 Bedienungsanleitung
Table of Contents | Next Page
TT700
Mending Machine
TT700 Instruction Manual
Previous Page | Next Page
TT700
TABLE OF CONTENTS
Handy Reference Guide 03
Getting Ready to Mend 07
Winding the Bobbin 08
Inserting the Wound Bobbin 11
Threading the Machine 12
Working Light 13
Raising the Bobbin Thread 14
Mending a Broken Seam 15
Securing a Seam 16
Free Arm Mending 16
Adjusting Tension 17
Changing Needles 18
Bobbin Case Replacement 19
Performance Checklist 25
Even if you have sewn before,
these instructions will make your
first use much easier!
TT700 Instruction Manual
Table of Contents Previous Page | Next Page
TT700
3
PARTS AND ACCESSORIES
Table of Contents Previous Page | Next Page
TT700
4
PARTS AND ACCESSORIES
5
Table of Contents Previous Page | Next Page
TT700
ACCESSORIES INCLUDED
in Accessory Drawer
•3 Bobbins (1 in machine)
For replacement bobbins,
use Class 66 bobbins
• 1 needle threader
•2 needles (1 in machine)
For replacement needles,
Use Size 90/14 needles.
•Combination seam ripper/thread
trimmer tool
Table of Contents Previous Page | Next Page
TT700
6
IMPORTANT SAFEGUARDS
•Before connecting machine, be sure that the voltage on the AC adapter
matches your electrical supply.
•Always disconnect the foot switch or AC adapter when changing needles,
removing the bobbin, or cleaning the machine.
•Always disconnect the AC adapter whenever machine is unattended.
• Work carefully and watch the sewing area to avoid the needle during operation.
•Do not pull the fabric while mending as the needle may bend and break or
cause other damage
• Check that the machine is threaded carefully before mending.
•The bobbin case tension is Pre-set at the factory and cannot be adjusted.
• If the thread gathers underneath the material, this indicates that the tension
needs to be increased e.g., for cotton material the tension should be
tightened as far as it will go then turned anti-clockwise 2 and a half turns.
•Please avoid sideways pressure on the needle when sewing around corners
as this could cause the machine to jam and render it inoperative.
Table of Contents Previous Page | Next Page
TT700
7
GETTING READY TO MEND
1. Assemble spool holder by snapping spool
pin into spool stand.
2. Slide spool stand into its holder on rear left
of machine, until it snaps firmly into place.
Then install spool cap on spool pin
3. Make sure that power switch is in the ON
position. Plug in foot switch and AC
adapter plugs.
4. Remove red-handled seam ripper/thread
trimmer and needle threader from
accessory drawer.
Table of Contents Previous Page | Next Page
TT700
8
WINDING THE BOBBIN
1. Push bobbin winder switch down to raise
bobbin winder.
2. Remove see-through bobbin cover by
pulling it upwards.
Check that bobbin case is in proper posi-
tion. The bobbin case is held in place by a
position plate which is designed to flex
slightly to allow the bobbin case to move
back and forth freely, about 1/16"
Screw head should line up with seam in
plastic casing of machine and bobbin case
should move back and forth slightly (about
1/16'') when handwheel is turned. If not,
refer to page 17 for repositioning instruc-
tions.
3. Remove empty bobbin from bobbin case.
The seam ripper may make removal easi-
er.
Place bobbin on bobbin winder, aligning
hole in bobbin with driving pin on bobbin
winder. You may have to turn the handwheel
to help locate the driving pin.
Table of Contents Previous Page | Next Page
TT700
9
WINDING THE BOBBIN continued...
4. Install spool cap on spool pin.
Slide spool of thread onto spool pin.
5. Pull thread from spool and, using two
hands, pull it through diagonal slit in first
thread guide.
First thread guide should look like this
when properly threaded.
6. Wrap thread one time counterclockwise
around tension disc.
Table of Contents Previous Page | Next Page
TT700
10
WINDING THE BOBBIN continued...
7. Feed end of thread through small hole in
top of bobbin from the inside, leaving a 3"
tail.
8. Slide power switch into ON Position Hold
end of thread (the "tail") firmly and step
on foot switch until a few coils are wound
onto bobbin and stop.
9. Use thread trimmer to cut off tail, flush
with top of bobbin. Continue winding until
desired amount of thread is wound on
bobbin. A full bobbin holds 35 yards.
10. Cut thread about 4" from bobbin and
remove from machine. Leave spool of
thread on spool pin on back of machine.
Push bobbin winder switch up into off
position.
Inhaltsverzeichnis
Andere Singer Nähmaschine Handbücher
Singer
Singer 212W140 Gebrauchsanweisung
Singer
Singer 96-10 Bedienungsanleitung
Singer
Singer HD6360 Bedienungsanleitung
Singer
Singer 71-107 Bedienungsanleitung
Singer
Singer Scholastic 85SCH Bedienungsanleitung
Singer
Singer 246-31 Installations- und Betriebshandbuch
Singer
Singer 8060 Bedienungsanleitung
Singer
Singer 236U120 Bedienungsanleitung
Singer
Singer 375B1 Bedienungsanleitung
Singer
Singer One Bedienungsanleitung
Singer
Singer 107-1 Bedienungsanleitung
Singer
Singer 2932 Bedienungsanleitung
Singer
Singer 431 CONVERTIBLE Bedienungsanleitung
Singer
Singer QUANTUM QUILTER 7350 Bedienungsanleitung
Singer
Singer 5160 Bedienungsanleitung
Singer
Singer 281-1 Bedienungsanleitung
Singer
Singer 6-1 to 6-8 Bedienungsanleitung
Singer
Singer 6704 Bedienungsanleitung
Singer
Singer 630 Bedienungsanleitung
Singer
Singer 3270 Bedienungsanleitung
