Sintrones VMT-825 Bedienungsanleitung

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

VMT-825

User’s Manual

Edition：V 2.20

Model：VMT-825

Renew time：2011-07-20

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

The documentation and the software included with this product are copyrighted

2011 by Sintron Technology Corp. All rights are reserved.

Sintron reserves the right to make improvements in the products described in this

manual at any time without notice. No part of this manual may be reproduced,

copied, translated or transmitted in any form or by any means without the prior

written permission of Sintron Information provided in this manual is intended to be

accurate and reliable.

However, Sintron assumes no responsibility for its use, nor for any infringements

of the rights of third parties, which may result from its use.

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

FCC Class B

Note: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and receiver.

. Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected. Consult the dealer or an experienced radio/TV technician for

help.

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

Technical Support and Assistance

1. Visit the Sintron web site at www.sintroncorp.com where you can find the

latest information about the product.

2. Contact your distributor, sales representative, or Sintron’s customer service

center for technical support if you need additional assistance. Please have the

following information ready before you call:

. Product name and serial number

. Description of your peripheral attachments

. Description of your software (operating system, version, application software,

etc)

. A complete description of the problem

. The exact wording of any error messages

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting

it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment

from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power

source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened

only by qualified service personnel.

The sound pressure level at the operator’s position according to IEC 704-1:1982 is

no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Sintron

disclaims all responsibility for the accuracy of any statements contained herein.

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

Contents

Chapter 1 General Information.............................................................................9

1.1 Introduction ............................................................................................................................................. 9

1.2 General Specifications............................................................................................................................. 9

1.3 LCD Specifications .................................................................................................................................11

1.4 Dimensions ............................................................................................................................................. 12

Chapter 2 System Setup........................................................................................13

2.1 A Quick Tour of the Vehicle Mounted Computer.............................................................................. 13

2.2 Installation Procedures ......................................................................................................................... 16

2.2.1 Connecting the Power Cord....................................................................................................... 16

2.2.2 Connecting the Keyboard or Mouse ......................................................................................... 16

2.2.3 Switching On the Power............................................................................................................. 16

2.3 Running the BIOS Setup Program....................................................................................................... 17

2.4 Installing System Software.................................................................................................................... 17

2.5 Installing the Drivers............................................................................................................................. 18

Chapter 3 Hardware and Peripheral Installation..............................................19

3.1 Overview of Hardware Installation and Upgrading........................................................................... 19

3.2 Installing the Storage Device ................................................................................................................ 19

3.2.1 Installing the 2.5" hard disk drive (HDD)................................................................................ 19

3.2.2 Installing the Compact Flash Card (CFC) ............................................................................... 21

3.3 Placing the Rubber Seal........................................................................................................................ 22

3.4 Installing the Optional Accessories...................................................................................................... 22

3.4.1 Installing the .Universal Arm. ................................................................................................... 23

3.4.2 Installing RAM-MOUNT .kits................................................................................................... 23

3.4.3 Installing the MiniPCI WLAN module..................................................................................... 24

3.4.4 Installing GPS and GSM/GPRS modules................................................................................. 25

Chapter 4 Jumper Settings and Connectors.......................................................28

4.1 Setting Jumpers ..................................................................................................................................... 28

4.1.1 Jumpers and switches................................................................................................................. 28

4.1.2 Locating jumpers and switches.................................................................................................. 29

4.1.3 Connectors on the motherboard................................................................................................ 30

4.1.4 Locating connectors on the motherboard................................................................................. 31

4.1.5 Jumpers and switches on power board..................................................................................... 32

4.1.6 Locating jumpers, connectors and LEDs on power board...................................................... 33

4.2 CPU Installation..................................................................................................................................... 34

4.3 Jumper Settings on Mother-Board ...................................................................................................... 34

4.3.1 LCD panel power setting (JP1).................................................................................................. 34

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

4.3.2 Panel Type Setting (JP5)............................................................................................................ 34

4.3.3 CMOS clear for external RTC (JP2) ........................................................................................ 35

4.4 COM-port Interface .............................................................................................................................. 36

4.4.1 COM port Pin 9 power output setting (JP3)............................................................................ 37

4.4.2 COM port Pin 9 power output value setting (JP4).................................................................. 37

4.5 Jumper Setting on Power-Board.......................................................................................................... 38

4.5.1 Low battery monitor and shut down (CN2)............................................................................. 38

4.5.2 Power off delay setting connector (CN7).................................................................................. 38

4.5.3 Ignition input switch jumper (CN8).......................................................................................... 39

Chapter 5 Intel Chipset.........................................................................................40

5.1 Introduction ........................................................................................................................................... 40

5.1.1 Installation for Windows 98....................................................................................................... 40

5.1.2 Installation for Windows 2000 / XP .......................................................................................... 40

5.2 Further Information.............................................................................................................................. 41

Chapter 6 Graphic Chipset ..................................................................................42

6.1 Introduction ........................................................................................................................................... 42

6.1.1 Installation for Windows 2000 / XP .......................................................................................... 42

6.2 Further Information.............................................................................................................................. 42

Chapter 7 Audio ....................................................................................................43

7.1 Introduction ........................................................................................................................................... 43

7.2 Installation of Audio Driver.................................................................................................................. 43

Chapter 8 USB 2.0.................................................................................................44

8.1 Introduction ........................................................................................................................................... 44

8.2 Installation of USB Driver .................................................................................................................... 44

Chapter 9 Touchscreen.........................................................................................45

9.1 Introduction ........................................................................................................................................... 45

9.1.1 General information................................................................................................................... 45

9.1.2 General specifications................................................................................................................. 45

9.2 Installation of Touchscreen Driver ...................................................................................................... 46

9.2.1 Windows 98-Me-2000-2003 driver ............................................................................................ 46

9.2.2 Windows XP driver .................................................................................................................... 47

9.3 Further Information.............................................................................................................................. 47

Appendix A Pin Assignments..................................................................................48

A.1 Inverter power connector (CN2) ......................................................................................................... 48

A.2 Internal speaker connector (CN21)..................................................................................................... 48

A.3 IDE hard disk drive connector (CN5)................................................................................................. 49

A.4 LVDS connector (CN1) ........................................................................................................................ 50

A.5 COM 1, 2................................................................................................................................................ 51

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

A.6 COM 3, 4................................................................................................................................................ 52

A.7 COM 3, 4 internal connector (CN18, 16)............................................................................................ 53

A.8 Internal USB port ................................................................................................................................. 54

A.9 Reserved Parallel port connector (CN11)........................................................................................... 55

A.10 Power Inlet........................................................................................................................................... 56

Appendix B Key Features Setting in BIOS............................................................57

B.1 Panel Type Setting in BIOS.................................................................................................................. 57

B.2 Power Fail Function Setting in BIOS.................................................................................................. 59

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

Chapter 1 General Information

1.1 Introduction

VMT-825 is fanless and is supplied with either Intel ULV Celeron® M or LV CPU

for higher reliability and performance. The ruggedized aluminum enclosure is built

without ventilation holes and makes VMT-825 waterproof and dust proof.

A power source with wide input range suits vehicles such as forklifts and trucks,

which typically operate with 12 V, 24 V, or 48 V DC power. When equipped

with an adapter, it can operate with AC power.

VMT-825 provides 10/100Base-T Ethernet, and expansion options for wireless

transmissions such as 802.11b/g, GPS, GSM and GPRS, etc.

Embedded OS support (WinCE.NET, WinXP Embedded), using OS images can

greatly shorten system development and trouble-shooting.

1.2 General Specifications

General

• Dimensions (W x H x D): 310 x 255 x 90 mm ;

• Weight: 4.8 kg

• Power supply:

Minimum Input voltage: 6 Vdc. (Supports cold crank Ignition)

Maximum Input voltage: 58 Vdc.

Minimum Startup voltage: 9 Vdc.

Low battery shut-down protection threshold (option): 11 Vdc.

(When the battery voltage level drops below 11V in the vehicle for more

than 30 seconds, the system will start to shut down in order to prevent

battery being drained and will automatically re-activate only when the

voltage is greater than 11V.)

Power Off delay (option):30 seconds.

(When system power is con-trolled by ignition key, then whenever the key

is turned off, the computer system will power-off completely after 30

www.sintroncorp.com

Address: 2880 Zanker Rd, Suite 207, San Jose CA 95134 USA TEL: 408-800-1413 / FAX: 510-952-8282 / sales@sintroncorp.com

seconds while the OS terminates.)

* For more detail of optional function please refer to Chapter 4, Sec-

tion 4.5 of this manual.

• Disk drive housing: Space for one 2.5" HDD or Compact Flash Card

• Front panel and back cover: IP65 Sealed; NEMA4 compliant

• Enclosure: Ruggedized aluminum without ventilation holes

Standard PC functions

• CPU: Intel ULV Celeron M 600MHz with 512 KB L2 cache /LV Pentium M

1.1GHz with 1MB L2 cache

• BIOS: Award 4 MB Flash BIOS, ACPI 2.0 Compliant

• System chipset: Intel 855GME and ICH4-M

• Front side bus: 400 MHz

• System memory: Two 184-pin DIMM sockets, accepting up to 2 GB

DDR 333 SDRAM

• IDE interface: Supports one connector. One channel supports two IDE devices.

Each IDE supports PIO modes 0 ~ 4, DMA mode 0 ~ 2, and

Ultra DMA 33/66/ 100 simultaneously

• Keyboard/mouse connector: Supports 1 standard PS/2 Keyboard and a PS/2

Mouse

• Serial ports: Four serial ports with two RS-232/422/485 ports (COM1, COM 2;

adjust by BIOS), and two RS-232 port (COM3, COM 4). All

ports are compatible with 16C550. UARTs and +5V/+12V power

supply are selectable

• Universal serial bus (USB) port: Supports up to two EHCI USB2.0

• Mini PCI bus expansion slot: Accepts one type III A/B mini PCI bus card

• Solid state disk: Supports one 50-pin socket for Compact Flash type I/II (True

IDE mode)

• Watchdog timer: 256-level interval from 1 to 255 seconds. Jumper less

selection and software can be enabled / disabled.

• Battery: 3.0 V @ 195 mA lithium battery

• Power management: Supports power saving modes including Normal/

Standby/Suspend modes. APM 1.2 compliant

Inhaltsverzeichnis

Andere Sintrones Desktop Handbücher

Sintrones

Sintrones SBOX-2110 Bedienungsanleitung

Sintrones

Sintrones SBOX-2600 Bedienungsanleitung

Sintrones

Sintrones ABOX-5000PG1 Bedienungsanleitung

Sintrones

Sintrones DSS-1300 Bedienungsanleitung

Sintrones

Sintrones VBOX-3620-M12X Bedienungsanleitung

Sintrones

Sintrones VBOX-3200 Bedienungsanleitung

Sintrones

Sintrones VBOX-3000 Bedienungsanleitung

Sintrones

Sintrones SBOX-2150 Bedienungsanleitung

Sintrones

Sintrones VBOX-3611-4L Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung