Siruba 700K Bedienungsanleitung
700K(BKF)
電控參數說明書
ELECTRONIC CONTROL PARAMETER MANUAL
0
1. 安裝衣襬尺寸導引器 / Welt Guide
Installation……………………………………………………..
2. 檢查及校正位置檢測器 / Checking and Positioning the Position Detector…………………………..
3. 校位及調整衣襬尺寸導引器 / Positioning andAdjusting the Welt Guide………………………………...
A. 盲縫平縫區 Blind Stitch Hemming the Flat Seam Section………………………………………………..
B. 盲縫段縫部
Blind Stitch H
emming the Cross Seam Section…………………………………………….
4. 檢查及調整摺疊器 / Checking andAdjusting the Folder……………………………………………..…
5. 控制箱說明 / Description of the Control Box………………………………………………………………
A. 前視圖 / Front View……………………………………………………………………………………
B. 後視圖 / Rear View…………………………………………………………………………………….
6. 跨越縫檢測器調整 / Adjusting the Cross Seam Detector ………………………………………………….
7.GUDE針數設定 / Setting GUDE Stitch Numbers……………………………………………………………..
A. 吸風功能 / Suction Function…………………………………………………………………………..
B. 斬刀功能 / Type Cutter Function………………………………………………………………………
C. 自動拷下擺功能 / Retractable Guide………………………………………………………………
目次
頁次
1
2
5
6
7
8
9
9
10
11
12
12
12
13
1
1. 安裝衣襬尺寸導引器 / Welt Guide
Installation
A.左右調整將左邊的可撇式導板和落針處中心線對齊。
Making a left or right adjustment, to align the left side of the retractable guide with the center line of the needle.
B.前後調整可將可撇式導板尾端對齊切刀。
Making a forward or backward adjustment, to align the end of the retractable guide with the
cutter.
C.調整可撤式導板座高度 / Adjusting the height of retractable guide base
⑴如圖所示，放鬆螺絲以調整可撤式導板座。
Loosenthe screwto adjust the retractable guidebase as shownin the
figure.
⑵可撤式導板座應和針板平行並間隔
0.03mm
。
The
retractable
guidebase should
be
parallel to
the needleplate witha 0.03mm
clearance.
針中心
Center of the needle
可撒式導板
Retractable guide
對齊
Line to align with
前後調整螺絲
Front-to-back
ad
j
ustment screw.
高度調整螺絲
Height adjustment screw
2
2. 檢查及校正位置檢測器 /Checking and Positioning the Position Detector
A.電源開啟 Turn power ON.
B.檢查指示燈是否有亮 Check whether the indicator lamp is on.
指示燈
Indicator lamp
3
C. 輕壓檢測器確認位置，檢測器是否亮燈。
Press the detector lightly in to confirm that the cross seam section detector lamp turns on.
⑴未碰觸時，指示燈① OFF，指示燈② ~ ⑥ON。
Without touching, NO.1 detector lamp is OFF, NO.2~NO.6 detector lamps are ON.
⑵輕壓到底，指示燈① ON，指示燈② ~ ⑥OFF。
Press the detector lightly, NO.1 detector lamp is ON, NO.2~NO.6 detector lamps are OFF.
⑶如動作異常，請參考 E「調整感測器位置」，進行感測器位置調整。
If malfunction occurs, please refer to E "Adjusting the Sensor Position " to adjust the position of sensor.
D.調整調節旋鈕，設定所需靈敏度。
Adjust the adjustment knob, set up the required sensibility.
輕押確認
Press lightly to confirm
①②③④⑤⑥
① ② ③ ④ ⑤ ⑥
- +
4
E. 調整感測器位置 / Adjusting the Sensor Position
⑴鬆開固鎖螺絲。
Loosen the locking screw.
⑵使用三用電表，量測感測器輸出電壓(DC)。
Use multimeter meter to measure the output DC voltage of sensor.
⑶旋轉調節螺絲，調整感測器位置，使感測器輸出電壓介於 DC0.5~0.6V，此時鎖緊固鎖螺絲固定感測器位置。
As shown in the following figure, rotate the adjustment screw to adjust the position of sensor, make the output DC
voltage of sensor lie within 0.5 ~ 0.6V, and then tighten the locking screw to secure the position of sensor.
註：鎖緊固鎖螺絲後，務必確認感測器輸出電壓仍然介於 DC0.5~0.6V 之間
As shown in the following figure, rotate the adjustment screw to adjust the position of sensor, make the output DC
voltage of sensor lie within 0.5 ~ 0.6V, and then tighten the locking screw to secure the position of sensor.
鬆開固鎖螺絲
Loosen the locking screw
調整調節螺絲
Adjust the adjustment screw
紅色探棒 黑色探棒
Red probe Black probe
5
3. 校位及調整衣襬尺寸導引器 / Positioning and Adjusting the Welt Guide
為了防止漏縫，當檢測器檢測到段縫時，可撤式導板會內移，將布料也往內移，如圖所示。接著，
操作盲縫以好的線跡蓋過段縫。蓋過段縫後，可撤式導板會外移回歸原位，恢復正常盲縫操作，
如圖所示。
In order to prevent skip stitching, when a cross seam is detected by the sensor, the retractable guide
starts moving inside and moving the fabric inward, as shown in the following figure. Then, the cross
seam section is sewn over with fine stitches in blind stitch hemming operation. After the cross seam
section sewn, the retractable guide returns to the normal position and the normal blind stitch operation is
resumed, as shown in the following illustration.
→
→
6
A.盲縫平縫區 Blind Stitch Hemming the Flat Seam Section.
平縫區
Flat seam section 若縫寬度過大時，順時針旋
轉調節螺絲
If the seam width is too
wide, turn the adjusting
screw clockwise.
若縫寬度過小時，反時針旋轉調
節螺絲
If the seam width is too narrow
turn the adjustment screw
counter clockwise.
調整調節螺絲
Adjust the
adjustment screw
轉鬆螺絲
Loosen the screw
可撒式導板座水平移動
The retractable guide base moves
horizontally
7
B. 盲縫段縫部
Blind Stitch Hemming the Cross Seam Section.
段縫部
Cross seam section
若段縫處前後縫 寬 過 大，順
時針旋轉螺帽
If the seam widthis too
wide before and after the
cross seam section, turn the
nut clockwise.
如在段縫處前後布料漏縫,
逆時針轉螺帽
If the stitches are missing
before and after the cross
seam section, turn the nut
counter clockwise.
調整調節螺絲
Adjust the adjustment screw
轉鬆螺帽
Loosen the locking nut
8
織物厚度 The thickness of the fabric to be sewn.
4. 檢查及調整摺疊器 / Checking and Adjusting the Folder
將摺疊器前緣和檢測器的間隔調整成縫紉布料的厚度。
Adjust the gap between the leading edge of the folder and the detector into the thickness of the
fabric to be sewn.
Andere Handbücher für 700K
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Siruba Nähmaschine Handbücher
Siruba
Siruba HF008A Bedienungsanleitung
Siruba
Siruba DL7200B Bedienungsanleitung
Siruba
Siruba VC008B Bedienungsanleitung
Siruba
Siruba DL3880 Series Bedienungsanleitung
Siruba
Siruba C007K Bedienungsanleitung
Siruba
Siruba AA-6 Bedienungsanleitung
Siruba
Siruba HSM-2722 Bedienungsanleitung
Siruba
Siruba DT8200 Series Bedienungsanleitung
Siruba
Siruba PK511 Bedienungsanleitung
Siruba
Siruba 700L-BKF1 Bedienungsanleitung
Siruba
Siruba T828-TP Datenblatt
Siruba
Siruba HSP-68100 Bedienungsanleitung
Siruba
Siruba C007JP Bedienungsanleitung
Siruba
Siruba VC008 VSQ Bedienungsanleitung
Siruba
Siruba DL7200 Bedienungsanleitung
Siruba
Siruba 700QD Bedienungsanleitung
Siruba
Siruba 700KS-LFD6-K1 Bedienungsanleitung
Siruba
Siruba DL720 Bedienungsanleitung
Siruba
Siruba PK522 Datenblatt
Siruba
Siruba R718K Bedienungsanleitung
