Skil 1810 Montageanleitung

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

Operating/Safety Instructions

Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento y seguridad

1810

1815

1820

1825

For English Version Version française Versión en español

See page 2 Voir page 18 Ver la página 34

1-877-SKIL999 (1-877-754-5999) www.skil.com

Call Toll Free for

Consumer Information

& Service Locations

Pour obtenir des informations

et les adresses de nos centres

de service après-vente,

appelez ce numéro gratuit

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 1

-2-

Work area safety

Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

Electrical safety

Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of electric

shock.

Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk

of electric shock if your body is earthed or

grounded.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

If operating the power tool in damp locations

is unavoidable, use a Ground Fault Circuit

Interrupter (GFCI) protected supply. Use of

an GFC reduce the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention

while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the

switch is in the off-position before

connecting to power source and / or battery

pack, picking up or carrying the tool.

Carrying power tools with your finger on the

switch or energizing power tools that have the

switch on invites accidents.

emove any adjusting key or wrench before

turning the power tool on. A wrench or a

key left attached to a rotating part of the

power tool may result in personal injury.

Do not overreach. Keep proper footing and

balance at all times. This enables better

control of the power tool in unexpected

situations.

Dress properly. Do not wear loose clothing

or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose

clothes, jewelry or long hair can be caught in

moving parts.

If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce dust-

related hazards.

Power tool use and care

Do not force the power tool. Use the

correct power tool for your application. The

correct power tool will do the job better and

safer at the rate for which it was designed.

Do not use the power tool if the switch does

not turn it on and off. Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

ead all safety warnings and instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WA NINGS AND INST UCTIONS FO FUTU E EFE ENCE

The term “power tool” in all of the warnings refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

ARNING

General Power Tool Safety Warnings

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 2

-3-

Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment

or binding of moving parts, breakage of

parts and any other condition that may

affect the power tool’s operation. If damaged,

have the power tool repaired before use.

Many accidents are caused by poorly

maintained power tools.

Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

Use the power tool, accessories and tool

bits etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

Service

Have your power tool serviced by a qualified

repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional Safety Warnings

GFC and personal protection devices like

electrician’s rubber gloves and footwear will

further enhance your personal safety.

Do not use AC only rated tools with a DC

power supply. While the tool may appear to

work, the electrical components of the AC

rated tool are likely to fail and create a hazard

to the operator.

Keep handles dry, clean and free from oil

and grease. Slippery hands cannot safely

control the power tool.

Use clamps or other practical way to secure

and support the workpiece to a stable

platform. Holding the work by hand or against

your body is unstable and may lead to loss of

control.

Develop a periodic maintenance schedule

for your tool. When cleaning a tool be

careful not to disassemble any portion of

the tool since internal wires may be

misplaced or pinched or safety guard return

springs may be improperly mounted.

Certain cleaning agents such as gasoline,

carbon tetrachloride, ammonia, etc. may

damage plastic parts.

Risk of injury to user. The power cord must only

be serviced by a Skil Factory Service Center or

Autho rized Skil Service Station.

Some dust created by power

sanding, sawing, grinding,

drilling, and other construction activities

contains chemicals known to cause cancer,

birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and

other masonry products, and

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed

to filter out microscopic particles.

ARNING

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 3

-4-

Safety ules for outers

Hold tool by insulated gripping surfaces

when performing an operation where the

cutting tool may contact hidden wiring or

its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live"

and shock the operator.

Use clamps or other practical way to secure

and support the workpiece to a stable

platform. Holding the work by hand or against

your body is unstable and may lead to loss of

control.

Always make sure the work surface is

free from nails and other foreign objects.

Cutting into a nail can cause the bit and the

tool to jump and damage the bit.

Never hold the workpiece in one hand and

the tool in the other hand when in use.

Never place hands near or below cutting

surface. Clamping the material and guiding

the tool with both hands is safer.

Never lay workpiece on top of hard

surfaces, like concrete, stone, etc...

Protruding cutting bit may cause tool to jump.

Always wear safety goggles and dust

mask. Use only in well ventilated area.

Using personal safety devices and working in

safe environment reduces risk of injury.

After changing the bits or making any

adjustments, make sure the collet nut and

any other adjustment devices are

securely tightened. Loose adjustment

device can unexpectedly shift, causing loss

of control, loose rotating components will be

violently thrown.

Never start the tool when the bit is

engaged in the material. The bit cutting

edge may grab the material causing loss of

control of the cutter.

Always hold the tool with two hands

during start-up. The reaction torque of the

motor can cause the tool to twist.

The direction of feeding the bit into the

material is very important and it relates to

the direction of bit rotation. When viewing

the tool from the top, the bit rotates

clockwise. Feed direction of cutting must

be counter-clockwise. NOTE: inside and

outside cuts will require different feed

direction, refer to section on feeding the

router. Feeding the tool in the wrong

direction, causes the cutting edge of the bit

to climb out of the work and pull the tool in

the direction of this feed.

Never use dull or damaged bits. Sharp

bits must be handled with care. Damaged

bits can snap during use. Dull bits require

more force to push the tool, possibly causing

the bit to break.

Never touch the bit during or immediately

after the use. After use the bit is too hot to

be touched by bare hands.

Never lay the tool down until the motor

has come to a complete standstill. The

spinning bit can grab the surface and pull the

tool out of your control.

Never use bits that have a cutting

diameter greater than the opening in the

base.

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 4

-5-

IMPO TANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Diameter Size of drill bits, grinding wheels, etc.

n0No load speed Rotational speed, at no load

.../min Revolutions or reciprocation per minute Revolutions, strokes, surface speed,

orbits etc. per minute

0 Off position Zero speed, zero torque...

1, 2, 3, ... Selector settings Speed, torque or position settings.

, , , Higher number means greater speed

nfinitely variable selector with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class construction Designates Double nsulated

Construction tools.

Earthing terminal Grounding terminal

Warning symbol Alerts user to warning messages

Ni-Cad RBRC seal Designates Ni-Cad battery recycling

program

Symbols

This symbol designates

that this tool is listed by

Underwriters Laboratories.

This symbol designates

that this tool is listed by

the Canadian Standards

Association.

This symbol designates

that this tool is listed to

Canadian Standards by

Underwriters Laboratories. This symbol

designates

that

this tool

complies

to NOM

Mexican

Standards.

This symbol designates that

this tool is listed by

Underwriters Laboratories,

and listed to Canadian

Standards by Underwriters

Laboratories.

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 5

-6-

Functional Description and Specifications

Disconnect the plug from the power source before making any

assembly, adjustments or changing accessories. Such preventive safety

measures reduce the risk of starting the tool accidentally.

ARNING

outers

CHIP DEFLECTO

POP-UP

FINE ADJUSTMENT

KNOB

BASE CLAMP

LEVE

AI VENTS

ON/OFF

T IGGE

SWITCH

“LOCK ON”

BUTTON

BIT OTATION A OW

SUB-BASE

BASE

HANDLE

BASE

ELEASE

LEVE

DUST

PO T

SCALE

INDICATO

DEPTH SCALE

VA IABLE

SPEED DIAL

(Model 1825 only)

FIG. 1

FIG. 2

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 6

-7-

FIG. 3

PLUNGE

HANDLE

CHIP DEFLECTO

AI VENTS

BIT OTATION A OW

Model number 1810 1815 & 1820 1825

Voltage rating 120V 50 - 60Hz 120V 50 - 60Hz 120V 50 - 60Hz

Amperage rating 9A 10A 11A

No load speed n0 25,000/min n0 25,000/min n0 10,500-25,000/min

Collet capacities 1/4" 1/4" 1/4", 1/2"

On models 1810, 1815, 1820, & 1825 router motor unit must be used with either fixed base

type A, or plunge base Type B.

KNOB

DEPTH STOP

TU ET

DEPTH SCALE

POP-UP

FINE ADJUSTMENT

KNOB

DEPTH GAUGE

VA IABLE

SPEED DIAL

(Model 1825 only)

ON/OFF

T IGGE

SWITCH

DUST PO T ADAPTE

(Not included, available

as accessory)

BASE CLAMP

LEVE

SUB-BASE

PLUNGE

LOCK LEVE

BASE ELEASE

BUTTON

FIG. 4

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 7

-8-

Assembly

A wide assortment of router bits with different

profiles is available separately.

To prevent personal injury,

always remove the plug

from power source before removing or

installing bits or accessories.

INSTALLING A OUTE BIT

Place router upside down with the top of the

router resting on the bench. Another option is

to remove the motor from the base before

installing the bit.

1. Remove the chip shield.

2. Press collet lock to stop rotation of

armature shaft. NOTE: it may be necessary

to rotate collet chuck assembly to engage

collet lock (Fig. 5).

3. Next, use the collet wrench to loosen the

collet nut in counter-clockwise direction

(viewed from under the router).

4. nsert the shank of the router bit into the

collet chuck assembly as far as it will go,

then back the shank out until the cutters

are approximately 1/8" to 1/4" away from

the collet nut face.

5. With the router bit inserted and the collet

lock holding the armature shaft, use the

collet wrench to firmly tighten the collet nut

in a clockwise direction (viewed from

under the router). To ensure proper

gripping of the router bit, the shank of the

router bit must be inserted at least 5/8".

When the templet guide has

been removed from base, do

not use router bits greater than 2" in

diameter as they will not fit through the sub-

base.

To prevent damage to tool,

do not tighten collet nut

without a bit.

NOTE: The router bit shank and collet chuck

should be clean and free of dust, wood,

residue and grease before assembling.

EMOVING THE OUTE BIT

1. Press collet lock to stop rotation of

armature shaft and turn the collet chuck

assembly in a counter-clockwise direction.

2. Once the collet chuck assembly is

loosened continue to turn the collet chuck

assembly until it pulls the collet free from

its taper, and the router bit can be

removed.

NOTE: The collet chuck is self-extracting; it

is NOT necessary to strike the collet chuck to

free the router bit.

ARNING

CAUTION

ARNING

FIG. 5

BIT

COLLET LOCK

SHANK

W ENCH

BASE

COLLET

COLLET NUT

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 8

EMOVING MOTO F OM BASE

To remove motor from fixed bases:

1. Hold router in vertical position, open base

clamp lever, push base release lever in

direction of arrow and pull motor unit

upwards from base, just before the motor

is completely out of the base it will stop

moving. Then depress the base release

button, and pull motor unit upwards from

base (Fig. 7).

To remove motor from plunge base:

1. Hold router in vertical position, open base

clamp lever, depress base release button,

and pull motor upwards from base (Fig. 8).

INSTALLING MOTO IN BASE

To install motor in fixed base:

1. Release the base clamp lever.

2. Align the depth rod base with the pop-up

fine adjustment knob.

3. Slide motor into base until the base

release lever engages into the slot on the

motor unit (Fig. 7).

4. Lock the base clamp lever.

To install motor in plunge base:

1. Release the base clamp lever.

2. Align the depth rod base with the pop-up

fine adjustment knob.

3. Slide motor into base until the base

release stop button on motor engages into

the slot in the base (Fig. 8).

4. Lock the base clamp lever.

BASE

CLAMP

LEVE

COLLET CHUCK CA E

(Model 1825 only)

With the router bit removed, continue to turn

the collet nut counter-clockwise until it is

loose. To assure a firm grip, occasionally

blow out the collet chuck and clean with a

tissue or fine brush. The collet chuck is made

up of two component parts as illustrated (Fig.

6); check to see that the adapter sleeve if

needed is properly seated in the collet nut

and lightly thread the collet nut back onto the

armature shaft. Replace a worn or damaged

collet chuck assembly immediately.

AMATU E

SHAFT

COLLET

NUT

FIG. 6

COLLET CHUCK

ASSEMBLY

ADAPTE

SLEEVE

BASE ELEASE

LEVE

BASE ELEASE

BUTTON

MOTO UNIT

BASE

ELEASE

STOP BUTTON

DEPTH

BASE

CLAMP

LEVE

BASE

ELEASE

BUTTON

FIG. 7

FIG. 8

-9-

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 9

Skil routers are designed for speed, accuracy

and con venience in performing cabinet work,

routing, fluting, beading, cove-cutting, dove

tails, etc. They will enable you to accomplish

inlay work, decorative edges and many types

of special carving.

DEPTH ADJUSTMENT WITH FIXED BASE

FINE ADJUSTMENT KNOB

The pop up fine depth adjustment knob allows

precise bit height adjustments on your router.

To use the fine adjustment feature, release

the base clamp lever, pull up the fine

adjustment knob and turn the knob clockwise

to lower, or counterclockwise to raise the bit

(Fig. 2).

(Note that one full turn of the knob will raise or

lower the bit approximately 1/16"of an inch.)

After making depth adjustments, re-clamp

the motor.

NOTE: All depth adjustments must be made

with the base clamp lever released.

DEEP CUTS

For deeper cuts, make several progressively

deeper cuts by starting at one depth and

then make several subsequent passes,

increasing the cutting depth with each pass.

To be certain that your depth settings are as

desired, you may want to make test cuts in

scrap material before beginning work.

Operating Instructions

CHIP DEFLECTO

Always wear eye

protection. The chip

deflector is not intended as a safety

guard.

The chip deflectors help keep dust and chips

out of your face, it will not stop objects larger

than dust thrown from the bit.

To remove chip shield from bases, press

inward on deflector until it releases from base

and remove. To attach, place deflector into

position as shown in (Fig. 10). Then flex

sides of deflector while pushing until it snaps

into place.

INSTALLING AS140

TEMPLATE GUIDE ADAPTE

(Not included, available as accessory)

Place template guide adapter over the holes

in the center of the sub-base, align the two

threaded holes in the bottom of adapter with

the countersunk holes in sub-base. Fasten

adapter with the screws provided (Fig. 9).

-10-

TEMPLATE

GUIDE

ADAPTE

MOUNTING

SC EWS

OUTE

BASE

CHIP

DEFLECTO

FIG. 9

FIG. 10

ARNING

SM 1619X03874 04-09:SM 1619X03874 04-09 4/20/09 9:45 AM Page 10

Andere Handbücher für 1810

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Skil Netzwerk-Router Handbücher

Skil

Skil RAS900 Montageanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung