Skil 3300MS Montageanleitung

For English Version Version française Versión en español

See page 2 Voir page 13 Ver la página 24

Operating/Safety Instructions

Consignes d’utilisation/de sécurité

Instrucciones de funcionamiento y seguridad

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

1-877-SKIL999 (1-877-754-5999) www.skil.com

Call Toll Free for

Consumer Information

&Service Locations

Pour obtenir des informations et

les adresses de nos centres de

service après-vente,

appelez ce numéro gratuit

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

3300MS

SM_2610957116_05-08 6/5/08 7:44 AM Page 1

Read and understand all instructions.

Failure to follow all instructions listed

below and in your miter saw manual may result in

serious personal injury.

Fully assemble and tighten all the fasteners

required for this stand. Also remember to

occasionally check the stand and make sure it is

still tight. Aloose stand is unstable and may shift in

use and cause serious injury.

Turn tool switch off and disconnect power before

mounting to the stand. Unintended startup during

assembly can cause injury.

Before operating make sure the entire unit is

placed on a solid, flat, level surface. Serious injury

could occur if tool with stand is unstable and tips.

Never stand on tool or its stand or use as ladder or

scaffolding. Serious injury could occur if the tool is

tipped or the cutting tool is accidentally contacted. Do

not store materials on or near the tool such that it is

necessary to stand on the tool or its stand to reach

them.

Use only Skil replacement parts. Any others may

create a hazard.

The Miter Saw should be firmly mounted to the stand

per the instruction manual.

After mounting the Miter Saw to the stand, align,

position and balance the Miter Saw per the instruction

manual.

Before use, verify that all stand parts are free from

damage and/or deformity.

Before use, verify that all parts or components of the

stand are properly installed.

Before use, swing open each of the legs until the pin

clicks, locking the legs in position.

When mounting the Miter Saw to the stand, make sure

that the tool mounting brackets are in the “UNLOCK”

position, so the tool mount will engage with the rails. Be

sure to hold the saw until it is secured to prevent it from

falling off the rails. Mounting bracket locking knobs

should then be tightened.

When removing the Miter Saw from the stand, loosen

the mounting bracket locking knobs until they rotate to

the “UNLOCK” position. Hold the Miter Saw firmly to

prevent the saw from falling off the rails. Carefully

remove the Miter Saw.

Do not modify the stand in any manner or use the

stand for any purpose other than is stated in these

instructions.

Because cut material may cause the stand to become

unbalanced, always be sure the material is supported

properly. Also, if the piece being cut is placed far

beyond the work support, stand legs on the opposite

side may suddenly be lifted up due to weight

imbalance. To prevent this from occurring, hold the

opposite side firmly before cutting.

Important Safety Instructions for Using

This Miter Saw Stand

WARNING

SM_2610957116_05-08 6/5/08 7:44 AM Page 2

Table of Contents

Safety Instructions for Miter Saw Stands..................2

Table of Contents......................................................3

Unpacking and Checking Contents ..........................4

Getting to Know Your Miter Saw Stand ....................5

Assembly ..............................................................6-9

Adjustments ............................................................10

Operation ................................................................11

Maintenance ..........................................................12

SM_2610957116_05-08 6/5/08 7:44 AM Page 3

For your own safety, never connect

plug to power source outlet until all

assembly steps are complete and until you have read

and understood the entire owner’s manual.

Model 3300MS Miter Saw Stand is shipped complete

inone box.

Unpacking and Checking Contents

Separate all parts from packing materials and check

each one with the “Table of Loose Parts” to make

sure all items are accounted for before discarding any

packing material.

If any parts are missing, do not attempt

to assemble the stand until the missing

parts are obtained and are installed correctly.

Table of Loose Parts

ITEM DESCRIPTION QTY.

A Miter Saw Stand 1

B Saw Mounting Brackets 2

C WorkSupports 2

D Work Stops 2

E Support Bar 1

STAND ASSEMBLY HARDWARE

(packaged in one bag)

F Work Stop Adjustment Knobs 2

G Carriage Bolts (M6 x 60 mm) 2

H Carriage Bolts (5/16 in. x 2 in.) 5

I Sliding Mounting Plates 4

JFlat Washers 5

K Lock Washers 5

L Nuts 5

M Operating Guide 1

Unpacking and Checking Contents

WARNING

GFH

IJKL

SM_2610957116_05-08 6/5/08 7:44 AM Page 4

Getting To Know Your Miter Saw Stand

1 Extension Adjustment Knob

2 Work Support

3Extension Rail

4 Work Stop Adjustment Knob

5Work Stop

6 Saw Mounting Bracket

7Work Support Adjustment Knob

8 Bracket Locking Knob

9 Adjustable Foot

SM_2610957116_05-08 6/5/08 7:44 AM Page 5

TOOLS NEEDED FOR ASSEMBLY

•Adjustable wrench

•Phillips®screwdriver

•Hammer and block of wood

PREPARING THE STAND

See Figure 1.

1. Lay the stand’s top surface down on the floor with

the folded legs on top.

2. Push in a leg locking pin (1) and rotate that leg up

until the locking pin clicks into place.

3. Repeat with the remaining three legs.

4. Lift the stand and place it in an upright position.

5. Check to ensure the stand is stable and all the legs

have the locking pins engaged.

ASSEMBLING AND INSTALLING

MATERIAL WORK SUPPORTS

See Figures 2 - 3.

The material work supports help balance the

workpiece during cutting operations.

To assemble the work support:

1. Slide a M6 x 60 mm carriage bolt (2) through the

square hole in the work support (3) and extend

through the other side.

2. Place the work stop (4) over the end of the bolt.

3. Thread a work stop adjustment knob (5) over the

end of the bolt and tighten to secure.

To install the work supports:

1.Slide the work support (3) into the extension rai (6)l.

Position the work support at the desired height on

the extension rail and tighten (7) in place.

2.Repeat with the other support.

FIG. 1

FIG. 2

FIG. 3

Assembly

SM_2610957116_05-08 6/5/08 7:44 AM Page 6

PERPARING SAW MOUNTING BRACKETS

See Figure 4.

Place a sliding mounting plate (1) onto each of four

5/16 in. x 2 in. carriage bolts (2) and feed bolts into

both mounting brackets (3) as shown in figure 4.

ATTACHING SAW TO

SAW MOUNTING BRACKETS

See Figure 5.

Always position the saw to achieve maximum balance

and stability. All four corners of the saw must be bolted

to the mounting brackets before use. Make sure bolts

do not extend above the table of the miter saw.

If the saw has four holes that line up with the slots

in the saw mounting brackets:

1. Unplug the saw and lock the saw arm in the down

position.

2. Lift one side of the saw and place a saw mounting

bracket underneath, aligning the carriage bolts with

the miter saw mounting holes, as shown in figure 5.

3. Lower the saw down onto the bracket, feeding the

carriage bolts through the mounting holes.

4. Secure in place using a flat washer (4),lock washer

(5),and nut (6).

5. Repeat steps 1 through 4 to install second bracket to

the other side of the saw.

6. After making sure both brackets are parallel to each

other, finger tighten all four nuts to hold in position.

FIG. 4

FIG. 5

Assembly

SM_2610957116_05-08 6/5/08 7:44 AM Page 7

Attaching saws with three mounting holes to saw

mounting brackets (Such as the Skil 3800 Miter

Saw):

See Figures 6 - 7.

1. Attach support bar (7) to rear carriage bolt of both

mounting brackets, as shown in figure 6.

2. Secure in place using a flat washer (8),lock washer

(9),and nut (10).

3. Unplug the saw and lock the saw arm in the down

position.

4. Lift and lower the saw down onto the brackets,

feeding the front carriage bolts through the front

mounting holes of the saw.

5. Insert a 5/16 in. x 2 in. carriage bolt (11) through the

support bar (7) and rear mounting hole of the saw.

5. Secure the three bolts using a flat washer (12),lock

washer (13),and nut (14).

6. After making sure both brackets are parallel to each

other, finger tighten all four nuts to hold in position.

FIG. 6

FIG. 7

Assembly

SM_2610957116_05-08 6/5/08 7:44 AM Page 8

MOUNTING THE MITER SAW TO THE STAND

See Figures 8 - 9.

1. Lift the saw and bracket assembly, allowing the

assembly to tilt slightly toward your body.

2. While still tilted toward you, hook the front edge of

the bracket assembly onto the front rail (1) of the

stand, figure 8.

To avoid serious personal injury,

make sure the curved front edge of

the mounting brackets are securely seated over

the front rail before seating the other end of the

brackets. Failure to do so could cause you to lose

control of the saw mounting assembly.

3. Lower the bracket assembly to allow the rear edge

of the bracket to seat fully over the rear rail,

figure 9.

4. Lock the brackets in position by tightening the

locking knobs (2).

NOTE: Continue to hold the mounting bracket

assembly with one hand until both levers are securely

locked.

5. Check position and adjust, if necessary, to make

sure the weight of the saw is evenly balanced over

the rails as shown in figure 9.

6. Ensure the saw is fully seated and locked in

position, then securely tighten the four nuts holding

the saw to the saw mounting brackets.

To remove saw from stand:

1. Loosen the locking knobs to unlock the saw and

mounting bracket assembly.

2. Lift the saw away from the rear rail of the stand to

disengage.

3. With the assembly tilted slightly toward you, lift the

front part of the assembly to disengage from the

front rail of the stand.

FIG. 8

FIG. 9

Assembly

WARNING

The mounting brackets are designed to fit snugly over the stand rails. With the locking knobs in the

tightened (locked) position, you should not be able to remove the saw and bracket assembly from

the rails. If the mounting brackets will not fit over the rails, or if the mounting brackets can be removed from the

rails when the brackets are locked, remove from the saw and bracket assembly immediately and tighten the

bracket adjustment screw as described in the Adjustments section of this manual. Failure to heed this warning

may result in personal injury.

WARNING

SM_2610957116_05-08 6/5/08 7:44 AM Page 9

Adjustments

BRACKET ADJUSTMENT SCREW

See Figure 10.

Mounting brackets are designed to fit snugly over the

stand rails. With the locking knobs are tightened to their

locked position, you should not be able to remove the

saw and bracket assembly from the rails. If the saw

and bracket assembly can be removed from the rails

when locked, the bracket adjustment screws need to

be tightened. If the saw and bracket assembly will not

fit over both rails, the bracket adjustment screws needs

to be loosened.

NOTE: The saw should be removed from the mounting

brackets before attempting to tighten or loosen the

bracket adjustment screws.

To adjust:

1. Use a wrench (1) to slightly loosen the nut (2).

2. Turn the screw (3) with a phillips screwdriver (4).

Rotate clockwise if the bracket assembly needs to

be tightened or counterclockwise if the assembly

needs to be loosened.

3. Install the bracket on the miter stand rails and

lower the locking lever to check the adjustment.

4. When the correct position is achieved, wrench

tighten the nut to secure.

5. Repeat with the second mounting bracket.

TO LEVEL STAND

See Figure 11.

The stand is equipped with an adjustable foot for

leveling the stand.

To adjust: loosen wing nut (1) and adjust the height of

the foot (2) by screwing the threaded shaft clockwise to

raise foot or counter-clockwise to lower foot. Retighten

wing nut securely.

To reduce the risk of injury, insure the

stand is stable and level before

operating the saw. Choose a level area to set-up the

stand and adjust the adjustable foot so that all four legs

are touching the ground.

FIG. 11

FIG. 10

WARNING

SM_2610957116_05-08 6/5/08 7:44 AM Page 10

Inhaltsverzeichnis

Sprachen:

Andere Skil Rack & Stand Handbücher

Skil

Skil 1300 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung