Skyrc D400 Bedienungsanleitung

Instruction Manual

[Version 1.2]

BALANCE CHARGER / DISCHARGER / POWER SUPPLY

Table of Contents

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the

appliance.

Do not recharge non-rechargeable batteries!

WARNING:

Introduction

Special Features

Warning and Safety Notes

Program Flow Chart

Operation

Power and Battery Connection

Operating Program

Lithium Battery Program (LiPo/LiFe/Lilon/LiHV)

NiMH/NiCd Battery Program

Pb Lead-Acid Battery Program

DC Power Supply

Battery Memory Set and Call Out

System Setting

Battery Meter

Battery Resistance Meter

Warning and Error Message

Using The Charge Control Software “charge Master”

SetContains

Specification

Conformity Declaration

Commonly Used Terms

Warranty and Service

Congratulations on your choice of SKYRC Ultimate Duo 400W AC/DC Balance

Charger / Discharger / Power Supply. This unit is simple to use, but the operation of

a sophisticated automatic charger such as SKYRC D400 does require some

knowledge on the part of the user. These operating instructions are designed to

ensure that you quickly become familiar with its functions. It is therefore important

that you read right through the Operating Instructions, Warning and Safety Notes

before you attempt to use your new charger for the first time. We hope you have

many years of pleasure and success with your new battery charger.

SKYRC D400 is a twin-channel charger with two independent circuits which can

charge two different kinds of batteries simultaneously. It also supports power

distribution in AC mode to get max charging power to shorten charging time. What’s

more, users could set the terminal voltage by themselves and connect it to PC for

PC control and firmware upgrade. Besides that, users could also use it as Lithium

Battery Meter and Battery Internal Resistance Meter. What's more, the

synchronization mode is available, in which users could perform synchronous

settings for charging same batteries simultaneously to offer time-saving benefits.

Your Ultimate Duo 400W can supply 150 Watts DC Power on channel 2. You can

use it to power equipments that require DC power. It converts standard household

power 100-240V AC to 6-15V DC power.

SKYRC D400 is a high-performance, micro processor control charge/ discharge

station with battery management suitable for use with all current battery types, with

integral equalizer for seven-cell Lithium-Polymer (LiPo), Lithium iron phosphate

(LiFe) and Lithium-Ion (LiIon) batteries; maximum 20A charge current and maximum

400W charge power. The additional LiHV mode is able to charge the new generation

of LiPo batteries with an end of charge voltage 4.35V. There are Automatic Charging

Current Limit, Capacity Limit, Temperature Threshold and Processing Time Limit

which makes the charger safe to use.

Please BE SURE to read these INSTRUCTIONS, WARNING and SAFETY NOTES

before you use the charger for the first time.

It can be dangerous to mis-handle batteries and battery chargers, as there is always

a risk of batteries catching fire and exploding.

Introduction

01 ·

D400

Introduction

· 02 D400

Please read this entire operating manual completely and attentively before using

this product, as it covers a wide range of information on operating and safety. Or

please do use this product in company with a specialist!

Output Socket 4mm Banana Plug

Balance Lead Socket

USB Port

Micro USB Port for PC Link

Temperature Sensor Port

Output Socket

4mm Banana

Plug

Balance Lead Socket

Temperature Sensor Port

LCD Display

Cooling Fan

Power

Switch

AC Socket

100-240V

DC Input

11-18V

DC Output

Cooling Fan

Resume or Start

Charge Processes

Scroll Through the Main Menu

Stop Any Charge Processes

Alter Values

See the Status of Individual

Cells in Balance Charge Mode

03 ·

D400

Twin-channel Charger

SKYRC D400 allows you to plug 2 batteries into one charger simultaneously, and it will

intelligently and automatically charge 2 battries at once to their maximum capacity. To top

of it, the batteries being charged do not even need to have the same configuration. You

can connect different chemistry(NiMH/NiCd/LiPo/LiFe/Lilon/LiHV/Pb)batteries into any of

the charging ports.

Dual Input and Power Distribution

It supports power distribution, for example, Channel 1-300W, then Channel 2-100W, the

total power is 400W. Please note the Max power for Channel 2 is 200W, but Channel 1

can reach to 400W.

Optimized Operating Software

SKYRC D400 features the so-called AUTO function that set the feeding current during the

process of charging or discharging. Especially for lithium batteries, it can prevent the

overcharging which may lead to an explosion due to the user's fault. It can disconnect the

circuit automatically and alarm once detecting any malfunction. All the programs of this

product were controlled through two way linkage and communication, to achieve the

maximum safety and minimize the trouble. All the settings can be configured by users!

Special Features

LiPo Battery

LiHV Battery

Special Features

· 04 D400

Internal Independent Lithium Battery Balancer

SKYRC D400 employs an individual-cell-voltage balancer. It isn't necessary to connect an

external balancer for balance charging.

Balancing Individual Cells Battery Discharging

During the process of discharging, SKYRC D400 can monitor and balance each cell of

the battery individually. Error message will be indicated and the process will be ended

automatically if the voltage of any single one cell is abnormal.

Adaptable to Various Type of Lithium Battery

SKYRC D400 is adaptable to various types of lithium batteries, such as LiPo, LiIon and

the new LiFe series of batteries.

LiHV Mode Available

The additional LiHV mode is able to charge the new generation of LiPo batteries with an

end of charge voltage 4.35 V.

Battery Memory (Data Store/Load)

The charger can store up to 10 different charge/discharge profiles for each channel. You

can keep the data pertaining to program setting of the battery of continuous charging or

discharging. Users can call out these data at any time without any special program

setting.

Terminal Voltage Control(TVC)

The charger allows user to change the end voltage. (for expert user only)

PC Control Software “Charge Master”

The free “Charge Master” software gives you unparalleled ability to operate the charger

through the computer. You can monitor pack voltage, cell voltage and other data during

the charging, view charge date in real-time graphs. And you can initiate, control charging

and update firmware from “Charge Master”.

With “Charger Master” and one computer, you could operate and update two channels

simultaneously.

Fast and Storage Mode of Lithium Battery

Purposes to charge lithium battery varies, 'fast' charge reduce the duration of charging,

whereas 'store' state can control the final voltage of your battery, so as to store for a long

time and protect useful time of the battery.

Automatic Charging Current Limit

You can set up the upper limit of the charging current when charging your NiMH or NiCd

battery, it is useful for the NiMH battery of low impedance and capacity in the 'AUTO'

charging mode.

Capacity Limit

The charging capacity is always calculated as the charging current multiplied by time. If

the charging capacity exceeds the limit, the process will be terminated automatically

when you set the maximum value.

Temperature Threshold*

The battery's internal chemical reaction will cause the temperature of the battery to rise.

If the temperature limit is reached, the process will be terminated.

This function is available by connecting optional temperature probe, which is not included in the package.

Processing Time Limit:

You can also limit the maximum process time to avoid any possible defect.

Battery Internal Resistance Meter

The user can check battery's total internal resistance and each cell's internal resistance.

LiPo Battery Meter

The user can check battery's total voltage, the highest voltage, the lowest voltage and

each cell's voltage.

Special Features

05 ·

D400

Re-Peak Mode of NiMH/NiCd Battery

In re-peak charge mode, the charger can peak charge the battery once, twice or three

times in a row automatically. This is good for making certain the battery is fully charged.

Delta-peak Sensitivity for NiMH/NiCd

Delta-peak sensitivity for NiMH/NiCd battery: The automatic charge termination program

based on the principle of the Delta-peak voltage detection. When the battery's voltage

exceeds the threshold, the process will be terminated automatically.

Cyclic Charging/Discharging

1 to 5 cyclic and continuous process of charge > discharge or discharge > charge is

operable for battery refreshing and balancing to stimulate the battery's activity.

These warnings and safety notes are particularly important. Please follow the

instructions for maximum safety; otherwise the charger and the battery can be

damaged or at worst it can cause a fire.

Never leave the charger unattended when it is connected to its power supply. If any

malfunction is found, TERMINATE THE PROCESS AT ONCE and refer to the

operation manual.

Keep the charger well away from dust, damp, rain, heat, direct sunshine and vibration.

Never drop it.

The allowable DC input voltage is 11~18V DC, and charge power 400W for 2 channels.

This charger and the battery should be put on a heat-resistant, noninflammable and

nonconductive surface. Never place them on a car seat, carpet or similar. Keep all

the inflammable volatile materials away from operating area.

Make sure you know the specifications of the battery to be charged or discharged to

ensure it meets the requirements of this charger. If the program is set up incorrectly,

the battery and charger may be damaged .It can cause fire or explosion due to

overcharging.

Be very careful to choose the correct voltage for different types of battery otherwise you

may cause damage to the batteries. Incorrect settings could cause the cells to fire or

explode.

Warning and Safety Notes

The allowable AC input voltage is 100~240V AC, and charge power 400W for 2 channels.

· 06 D400

Standard Battery Parameters

3.7V/cell

Nominal

Voltage

Min. Discharge

Voltage

Max Charge

Voltage

Storage

Voltage

Allowable

Fast Charge

3.7V/cell

4.2V/cell

3.8V/cell

≦1C

LiPo LiIon

3.6V/cell

4.1V/cell

≦1C

3.3V/cell

3.6V/cell

3.3V/cell

≦4C

LiFe

3.0-3.3V/cell 2.9-3.2V/cell 2.6-2.9V/cell

1.2V/cell

1.5V/cell

n/a

1C-2C

NiCd

1.2V/cell

1.5V/cell

n/a

1C-2C

NiMH

2.0V/cell

2.46V/cell

n/a

≦0.4C

0.1-1.1V/cell 0.1-1.1V/cell

1.8V/cell

LiHV

3.7V/cell

4.35V/cell

3.85V/cell

≦1C

3.1-3.4V/cell

A battery pack which consists of different types of cells (including different

manufacturers)

A battery that is already fully charged or just slightly discharged.

Non-rechargeable batteries (Explosion hazard).

Batteries that require a different charge technique from NiCd, NiMh, LiPo or Gel cell

(Pb, Lead acid).

A faulty or damaged battery.

A battery fitted with an integral charge circuit or a protection circuit.

Batteries installed in a device or which are electrically linked to other components.

Batteries that are not expressly stated by the manufacturer to be suitable for the

currents the charger delivers during the charge process.

Please bear in mind the following points before commencing charging:

Did you select the appropriate program suitable for the type of battery you are

charging?

Did you set up adequate current for charging or discharging?

Have you checked the battery voltage? Lithium battery packs can be wired in parallel

and in series, i.e. a 2 cell pack can be 3.7V (in parallel) or 7.4V (in series).

Have you checked that all connections are firm and secure?

Make sure there are no intermittent contacts at any point in the circuit.

Charging

During charge process, a specific quantity of electrical energy is fed into the battery.

The charge quantity is calculated by multiplying charge current by charge time. The

maximum permissible charge current varies depending on the battery type or its

performance, and can be found in the information by the battery manufacturer. Only

batteries that are expressly stated to be capable of quick-charge are allowed to be

charged at rates higher than the standard charge current.

Connect the battery to the terminal of the charger: red is positive and black is

negative. Due to the difference between resistance of cable and connector, the

charger can not detect resistance of the battery pack, the essential requirement

for the charger to work properly is that the charge lead should be of adequate

conductor cross-section, and high quality connectors which are normally gold-

plated should be fitted to both ends.

Always refer to the manual by battery manufacturer about charging methods,

recommended charging current and charging time. Especially, the lithium battery

should be charged according the charging instruction provided by the manufacturer

strictly.

Never attempt to charge or discharge the following types of batteries.

Warning and Safety Notes

07 ·

D400

Discharging

The main purpose of discharging is to clean residual capacity of the battery, or to

reduce the battery voltage to a defined level. The same attention should be paid to

the discharging process as charging. The final discharge voltage should be set up

correctly to avoid deep-discharging. Lithium battery can not be discharged to lower

than the minimum voltage, or it will cause a rapid loss of capacity or a total failure.

Generally, lithium battery doesn't need to be discharged. Please pay attention to the

minimum voltage of lithium battery to protect the battery.

Some rechargeable batteries have a memory effect. If they are partly used and

recharged before the whole charge is accomplished, they remember this and will only

use that part of their capacity next time. This is a memory effect. It is said that NiCd

and NiMH batteries are suffering from memory effect. NiCd has more memory effect

than NiMH.

Attention should be paid to the connection of lithium battery especially.

Do not attempt to disassemble the battery pack arbitrarily.

Please get highlighted that lithium battery packs can be wired in parallel and in series.

In the parallel connection, the battery s capacity is calculated by multiplying single

battery capacity by the number of cells with total voltage stay the same. The voltages

imbalance may cause fire or explosion .Lithium battery is recommended to charge in

series.

Warning and Safety Notes

· 08 D400

Inhaltsverzeichnis

Andere Skyrc Ladegerät Handbücher

Skyrc

Skyrc e6650 Bedienungsanleitung

Beliebte Ladegerät Handbücher anderer Marken

Fantec

Fantec QC3-A22 Bedienungsanleitung

Milwaukee

Milwaukee M1418C6 Bedienungsanleitung

ABB

ABB A145-M56 Bedienungsanleitung

Xantrex

Xantrex 817-1050 Bedienungsanleitung

Hama

Hama 173665 Bedienungsanleitung

Sony

Sony UCH20C Bedienungsanleitung

Cobra

Cobra GA-CC Bedienungsanleitung

Panasonic

Panasonic TH-50PB2W Bedienungsanleitung

ABB

ABB TPS48-F32 Bedienungsanleitung

Halo2Cloud

Halo2Cloud Pocket Power 3000 Bedienungsanleitung

Fantec

Fantec QuickCharge QC3-A11 Bedienungsanleitung

Perel

Perel AC088 Bedienungsanleitung

Inateck

Inateck AL4001 Bedienungsanleitung

Halo2Cloud

Halo2Cloud Pocket Power 6000 Bedienungsanleitung

EGO

EGO CH5500 Bedienungsanleitung

Fantec

Fantec QC3-A51 Bedienungsanleitung

Fubag

Fubag COLD START 300/12 Bedienungsanleitung

iCharger

iCharger 208B Bedienungsanleitung