SlimLine SLFMU Bedienungsanleitung
ISSUED: 12-02-09 SHEET #: 202-9418-1
Slimline Ultra-Thin Flat Mount for
23" to 46" LCD Flat Panel Screens
Model: SLFMU
Installation Guide
This product was designed to be installed on wood stud walls and solid concrete (2000 psi density
minimum) or cinder block walls. Before installing make sure the supporting surface will support the
combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten
screws or damage can occur or product may fail. Never exceed the Maximum UL Load Capacity.
This product is intended for indoor use only. Use of this product outdoors could lead to product
failure or personal injury. This mount is designed to attach the screen 0.33" from the wall. Please
refer to manufacturer's installation guide recommendations for required distance from wall to
avoid risk of injury or property damage. For support please call customer care at 1-800-865-2112.
WARNING
Max UL Load Capacity: 100 lb (45.4 kg)
©
UL
USC
I
D
:
0
0
0
0
0
1
8
7
6
2
2 of 44 ISSUED: 12-02-09 SHEET #: 202-9418-1
Tools Needed for Assembly
phillips screwdriver
drill
cinder block
level
hammer (optional)
C(2)D(2)
L(1)
E(4)
M5 x 12 mm F(4)
M5 x 25 mm
G(4)
M6 x 12 mm H(4)
M6 x 25 mm
K(1)
I(4)M(4)
M8 x 12 mm
N(4)
M8 x 25 mm
J(4)
ID .344" (8.74 mm)
A (1)
B (2)
3 of 44 ISSUED: 12-02-09 SHEET #: 202-9418-1
Installing to Wall
1
Use wall plate (A) as a template, make sure it is level, and mark two mounting holes along the center
A) and
attach to wall with two wood screws (C
Do not over tighten screws, or damage may occur.
WARNING
A
C
C
ATOP CUTAWAY VIEW
Wood screws must
center in stud
STUD
WARNING
4 of 44 ISSUED: 12-02-09 SHEET #: 202-9418-1
Installing to Solid Concrete or Cinder Block
1
Level wall plate (A
D) into holes and secure wall plate (A)
with two screws (C
C
A
D
SOLID CONCRETE
CINDER BLOCK
5 of 44 ISSUED: 12-02-09 SHEET #: 202-9418-1
anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, gener-
ally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90
hole instead of a hammer drill to avoid breaking out the back of the hole when entering a
void or cavity.
directly to load-bearing concrete.
WARNING
2A
D
C
1
D
concrete
Place plate (A) over anchors (D). Secure with screws (C). Tighten screws.
Drill holes and insert anchors (D).
WARNING
CUTAWAY VIEW
wall plate
drywall
wall plate
drywall
CORRECT
INCORRECT
concrete
concrete
6 of 44 ISSUED: 12-02-09 SHEET #: 202-9418-1
Installing Adapter Brackets
the screen. Place screen face side down. If screen has knobs on the back, remove them to allow the
adapter brackets to be attached. Place adapter brackets (B) on back of screen, align to holes, and
center on back of screen as shown below. Attach the adapter brackets to the back of the screen using
the appropriate combination of screws, washers, and spacers as shown in steps 2-1 or 2-2.
NOTE: Top and bottom holes of screen must always be used.
Verify that all holes are properly aligned, and then tighten screws using allen wrench (L).
2
X
X
B
CENTER BRACKETS
VERTICALLY
ON BACK OF
SCREEN
NOTE: "X" dimensions should be equal.
NOTE: For proceed to step 2-1. For bump-out or recessed back screen skip to
step 2-2.
7 of 44 ISSUED: 12-02-09 SHEET #: 202-9418-1
For Flat Back Screens
For Bump-Out or Recessed Back Screens
Begin with longer length screw, hand thread through washer, adapter bracket and spacer
in that order into screen as shown below. Screw must make at least three full turns into the
remaining mounting holes, level brackets and tighten screws.
If you have any questions, please call Peerless customer care at 1-800-865-2112
2-1
2-2
If you have any questions, please call Peerless customer care at 1-800-865-2112
bracket is still not tightly secured, damage may occur to screen or product may fail.
WARNING
SPACER (J)
SCREEN
WASHER (I)
SCREW
ADAPTER
BRACKET (B)
ADAPTER
BRACKET (B)
SCREEN SCREEN
WASHER (I) WASHER (I)
SCREW SCREW
SPACER (J)
ADAPTER
BRACKET (B)
Begin with the shortest length screw, hand thread through washer and adapter bracket into
screen as shown below. Screw must make at least three full turns into the mounting hole
mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of screen.
NOTE: If screen manufacturer's requirements state that more than 0.33" of ventilation is
required, spacers may be used to add an additional 0.5" of space between the wall and the
screen as shown right.
8 of 44 ISSUED: 12-02-09 SHEET #: 202-9418-1
Mounting and Removing the Flat Panel Screen
3
Guide hooks of adapter brackets (BA). Then slowly swing screen toward
detail 1.
To remove screen from mount, swing screen away from mount, and lift screen off of mount.
Always use an assistant or mechanical lifting
panel screens.
WARNING
A
B
VELCRO
DETAIL 1
WALL
WALL WALL
A
B
SCREEN
9 of 44 ISSUED: 12-02-09 SHEET #: 202-9418-1
To horizontally adjust screen, swing screen away from mount to disengage velcro, and slide screen
engage velcro.
10 of 44 ISSUED: 12-02-09 SHEET #: 202-9418-1
Inhaltsverzeichnis
Sprachen:
Andere SlimLine TV-Halterung Handbücher
