SlimLine SLTLU Bedienungsanleitung

ISSUED: 11-30-09 SHEET #: 202-9417-1
©
UL
USC
Slimline Ultra-Thin Tilt Mount
for 37" to 60" LCD Flat Panel Screens
Max UL Load Capacity: 100 lb (45.4 kg)
Model: SLTLU
Installation Guide
This product was designed to be installed on wood stud walls and solid concrete (2000 psi density
minimum) or cinder block walls. Before installing make sure the supporting surface will support the
combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws
or damage can occur or product may fail. Never exceed the Maximum UL Load Capacity. This product
is intended for indoor use only. Use of this product outdoors could lead to product failure or personal
injury. Depth of screen must be less than 2". This mount is designed to attach the screen 0.68" from the
wall. Please refer to manufacturer's installation guide recommendations for required distance from wall
to avoid risk of injury or property damage. For support please call customer care at 1-800-865-2112.
WARNING

2 of 52 ISSUED: 11-30-09 SHEET #: 202-9417-1
A (1)
B (2)
Tools Needed for Assembly
recommended)
phillips screwdriver
drill
level
hammer (optional)

3 of 52 ISSUED: 11-30-09 SHEET #: 202-9417-1
C(6)
E(6)
M4 x 12 mm
D(6)
F(4)
M4 x 25 mm G(4)
M5 x 12 mm
H(4)
M5 x 25 mm
I(4)
M6 x 12 mm J(4)
M6 x 20 mm K(4)
M6 x 25 mm L(4)
M6 x 30 mm
M(6)
M8 x 16 mm
N(4)
M8 x 25 mm O(4)
M8 x 40 mm
T(1)
P(4)
ID .219" (5.56 mm)
Q(4)
ID .344" (8.74 mm)
R(6)
S(1)

4 of 52 ISSUED: 11-30-09 SHEET #: 202-9417-1
Installing on Wall with Two Wood Studs
1
Use wall plate (A) as a template, make sure it is level, and mark four mounting holes along the center
A) and
attach to wall with four wood screws (C
A
C
Do not over tighten screws, or damage may occur.
WARNING
C
ATOP CUTAWAY VIEW
Wood screws must
center in stud
STUD
WARNING

5 of 52 ISSUED: 11-30-09 SHEET #: 202-9417-1
Installing on Wall with Three Wood Studs
1
Use wall plate (A) as a template, make sure it is level, and mark six mounting holes along the center
A) and
attach to wall with six wood screws (C
C
A
Do not over tighten screws, or damage may occur.
WARNING
C
ATOP CUTAWAY VIEW
Wood screws must
center in stud
STUD
WARNING

6 of 52 ISSUED: 11-30-09 SHEET #: 202-9417-1
Installing to Solid Concrete or Cinder Block
1
Level wall plate (A
D) into holes and secure wall plate
(A) with six screws (C
C
A
D
SOLID CONCRETE
CINDER BLOCK

7 of 52 ISSUED: 11-30-09 SHEET #: 202-9417-1
Drill holes and insert anchors (D).
concrete surface
1D
Place plate (A) over anchors (D). Secure with screws (C). Tighten screws.
A
D
C
2
anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, gener-
ally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90
hole instead of a hammer drill to avoid breaking out the back of the hole when entering a
void or cavity.
directly to load-bearing concrete.
WARNING
CUTAWAY VIEW
INCORRECT
CORRECT
drywall
wall plate
wall plate
concrete
concrete
drywall
WARNING

8 of 52 ISSUED: 11-30-09 SHEET #: 202-9417-1
Installing Tilt Brackets
If screen has obstructions on the back, remove them to allow the tilt brackets to be attached. Fully extend
tilt brackets (B) and place tilt brackets on back of screen. Align to holes, and center vertically on back of
screen as shown below. Attach the tilt brackets to the back of the screen using the appropriate combination of
screws, washers, and spacers as required
shown in steps 2-1 or 2-2.
NOTE: Top and bottom holes must always be used.
Verify that tilt brackets are properly aligned and then tighten screws using phillips screwdriver.
2
X
X
B
CENTER
BRACKETS
VERTICALLY
ON BACK OF
SCREEN
NOTE: "X" dimensions should be equal.
NOTE: Cut outs indicate
bottom of tilt brackets (B)
Notes:
depending upon the type of screen.
used, depending upon the type of screen.
washer that matches your screw size.
MEDIUM HOLE
FOR M5 SCREWS
SMALL HOLE
FOR M4 SCREWS
LARGE HOLE
FOR M6 SCREWS
MULTI-WASHER

9 of 52 ISSUED: 11-30-09 SHEET #: 202-9417-1
For Flat Back Screens
For Bump-Out or Recessed Back Screens
Begin with the shortest length screw, hand thread through multi-washer, tilt bracket and
spacer, if required, into screen as shown below. If screw cannot make three full turns into the
Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used depending on the type of screen.
NOTE: If screen manufacturer's requirements state that more than 0.68" of ventilation is
required, spacers may be used to add an additional 0.5" (spacer P) or 0.75" (spacer Q) of
space between the wall and the screen as shown below.
Begin with the shortest length screw, hand thread through multi-washer , tilt bracket and
spacer as required into screen as below. If screw cannot make three full turns into the screen
for remaining mounting holes, level brackets and tighten screws.
If you have any questions, please call Peerless customer care at 1-800-865-2112
2-1
2-2
If you have any questions, please call Peerless customer care at 1-800-865-2112
SCREEN
SPACER
MULTI-WASHER
SCREW
TILT BRACKET (B)TILT BRACKET (B)
SCREEN
MULTI-WASHER
SCREW
SCREEN
SPACER
SCREW
TILT BRACKET (B)
bracket is still not tightly secured, damage may occur to screen or product may fail.
WARNING
MULTI-WASHER

10 of 52 ISSUED: 11-30-09 SHEET #: 202-9417-1
Mounting the Flat Panel Screen
3
Fully extend tilt brackets (B) and move tilt brackets toward wall plate (A
-
DETAIL 1
FLANGES
B
B
B
A
Inhaltsverzeichnis
Sprachen:
Andere SlimLine TV-Halterung Handbücher


















