Smartbow W010 Bedienungsanleitung

User Manual

W01X SMARTBOW Wallpoint

W010, W011, W012

Smartbow GmbH T+43 (0) 7732 47200-0

Jutogasse 3, 4675 Weibern F+43 (0) 7732 47200-91

AUSTRIA [email protected]

www.smartbow.com

IMPORTANT

READ CAREFULLY BEFORE USE!

KEEP THE MANUAL FOR FUTURE CONSULTATION!

Smartbow GmbH T+43 (0) 7732 47200-0

Jutogasse 3 F+43 (0) 7732 47200-91

4675 Weibern, AUSTRIA [email protected]

www.smartbow.com

Table of content

1Introduction 5

1.1 General Information 5

1.2 Trademarks, Copyright and Disclaimer 5

2Electromagnetic Compatibility (EMC) 7

2.1 Europe 7

2.2 TR-CU 7

2.3 USA 7

2.3.1 User Information acc. to FCC15.21: 7

2.4 Canada 7

2.4.1 Part 15 Statement acc. FCC 15.19/RSS Gen Issue 4 Sect. 8.4 7

3Safety 8

3.1 Safety Labels 8

3.2 Signal words and their meaning 8

3.3 Operating states 9

3.4 Electrical safety 9

3.5 Operation 10

3.6 Repair and Service 10

3.7 Transport 10

3.8 Magnetic fields 11

3.9 Waste disposal/Environmental protection 11

4The SMARTBOW Wallpoint 12

4.1 General product information 12

4.2 Scope of supply 12

4.3 Technical Data 13

4.4 Modification on the SMARTBOW Wallpoint 16

4.5.1 General warranty conditions 17

4.5.2 Warranty coverage 17

4.5.3 Warranty exclusion 18

4.5.4 Support Hotline 18

5Installation 19

5.1 Installation of the SMARTBOW Wallpoint 19

5.2 Mounting the SMARTBOW Wallpoint 19

5.2.1 Installation option pipe clamp 21

5.2.2 Installation option special attachment for pipe 22

5.2.3 Installation option I-beam clamp 23

6Equipment 24

6.1 100101 Pipe clamp 24

6.2 100104 I-beam clamp 24

6.3 100105 Special attachment for pipe 24

7Transport and storage 25

7.1 Transport 25

7.2 Storage 25

7.3 Cleaning 25

8Troubleshooting 25

9Waste 26

10 Support 26

11 Declaration of Conformity 27

12 Lists 30

12.1 List of figures 30

12.2 List of tables 30

13 Glossary 30

14 Revision history 31

APPENDIX A: Specification PROFINET / Industrial Ethernet 32

Page 5 of 32

1 Introduction

1.1 General Information

Welcome to the SMARTBOW manual. We are happy that you have decided to buy our solution.

You will find the technical information, operating instructions and instructions for maintenance and fault

elimination. Read this information carefully before operating the SMARTBOW system and make sure you

are familiar with it. Non-observance may result in injury or damage to the system. If there is an unclear

point or if you would like to have more information, please contact our support. Please read through the

warranty conditions to know your rights and obligations.

Keep the manual within range, to be able to use it immediately.

1.2 Trademarks, Copyright and Disclaimer

SMARTBOW is a registered trademark of Smartbow GmbH.

The statements contained in this publication are only for information and should not be understood as a

sale offer. Certain products may not be available in some countries and the delivered products may differ

from those shown in the pictures. Neither this edition nor parts of it may be copied or published by print or

any other means without the written permission of Smartbow GmbH (in the following SMARTBOW).

The content of this publication has been compiled with the utmost care. Nevertheless, SMARTBOW is not

liable for any damages that may arise from errors or omissions in this publication.

The germen manual is the original manual. Translations into other languages are based on the German

manual as a source document. SMARTBOW is not liable for discrepancies between the original German

manual and versions in other languages. In case of conflicts in the content and accuracy of translated

manuals, the German manual is the reference document.

The compliance to this manual as well as the conditions and methods of installation, operation, use and

maintenance of the system cannot be monitored by the manufacturer. Improper installation can cause

damages to material and persons. Therefore, we assume no responsibility or liability for any loss, damage

or costs arising from incorrect installation, improper operation or incorrect usage and maintenance which

are associated in any way.

We also assume no responsibility for patent infringements or violations of the rights of third parties arising

from the use of this system.

Page 6 of 32

For improvement in terms of design, operation, and/or reliability SMARTBOW reserves the right to modify

the products described in this document without prior notice. SMARTBOW rejects from all liability related

with the use or application of the product described here.

All SMARTBOW products have been developed to assist farmers in their daily work with their herd as good

as possible. Because of variations in farm management, SMARTBOW cannot be responsible for the

economic results of each individual farm.

As soon as it becomes evident that safe operation is no longer possible (e.g. if there is visible damage),

remove the system immediately from power supply.

1.3 We ask for your feedback

All information of this manual has been compiled with the utmost care. The recommendations are intended

as guidelines. The instructions, illustrations and specifications in this manual are based on the current

information available at the time of publication. Your SMARTBOW system may contain improvements and

equipment or options that are not covered in this manual. New information based on the feedback from our

customers, are continuously updated and expanded.

We hope SMARTBOW fits your expectations and we like to receive your feedback (please send an email

to [email protected] or call +43 (0) 7732 47200-90).

The SMARTBOW Team

Page 7 of 32

2 Electromagnetic Compatibility (EMC)

2.1 Europe

For additional regulatory information, see the Regulatory Compliance homepage on

www.smartbow.com at the following location

https://smartbow.com/en/documents/documents-wallpoint.html

2.2 TR-CU

The Wallpoint W01X meets the requirements of the technical regulations of customs

union of Russia, Kazakhstan, Kyrgystan, Armenia and Belarus. The EAC sign on the

type label certifies the conformity to the safety requirment of customs union.

2.3 USA

2.3.1 User Information acc. to FCC15.21:

Changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

2.4 Canada

2.4.1 Part 15 Statement acc. FCC 15.19/RSS Gen Issue 4 Sect. 8.4

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Page 8 of 32

3 Safety

3.1 Safety Labels

The following safety labels are used on the different SMARTBOW products to warn against risks and

dangers.

Warning of a magnetic field

Hazards due to batteries

Risk of hand injury

European-label for the separate collection of electrical and electronic appliances

Further information in chapter 9 Disposal

The security labels on your product show important and useful information, which will help you to use and

maintain the SMARTBOWWallpoint safely. Follow to the instructions below to ensure that all labels remain

in perfect condition and in the right place.

Make sure that the safety labels are always clean and legible. Do not use solvents, souring agents or other

comparable cleaning agents which could damage the sticker.

Replace lost or illegible safety stickers.

Safety labels can be obtained from the SMARTBOW support.

3.2 Signal words and their meaning

The following signal words are used in the manual in order to warn the reader about risks and dangers.

Indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

Indicates a hazardous situation which, if not avoided, could result in

death or serious injury

Indicates a hazardous situation which, if not avoided, could result in

minor, moderate or serious injury.

Page 9 of 32

Indicates information considered important, but not hazard-related, e.g.

information relating to possible property damage.

These signal words are in accordance with the standard definition for civil applications in the European

Economic Area. Definitions that deviate from the standard definition may also exist in other economic

areas or military applications. It is therefore essential to make sure that the signal words described here

are always used just with the related product documentation and the related product. The use of signal

words in connection with unrelated products or documentation can result in misinterpretation and in

personal injury or material damage.

3.3 Operating states

The SMARTBOW Wallpoint may be operated only under the operating conditions and the positions

specified by the manufacturer. Applicable local or national safety regulations and rules for the prevention

of accidents must be observed in all work performed.

The SMARTBOW Wallpoint is exclusively produced for use in livestock sheds. Any other use is only

permitted with a written permission of Smartbow GmbH.

Do not place the SMARTBOW Wallpoint on heat-generating devices such as radiators or fan heaters.

The ambient temperature must not exceed the maximum temperature specified in the product

documentation or in the data sheet. Product overheating can damage the Wallpoint permanently.

3.4 Electrical safety

Unless expressly permitted, never remove the cover or any part of the housing while the SMARTBOW

Wallpoint is in operation. Doing so will expose circuits and components and can lead to injuries, or

damage to the SMARTBOW Wallpoint.

Any object that is not designed to be placed in the openings of the housing must not be used for this

purpose. Doing so can cause damage to the SMARTBOW Wallpoint.

Unless specified otherwise, the SMARTBOW Wallpoint is protected against the ingress of liquids. When

the cable entry cover is opened it must be protected against penetration by liquids. If the necessary

precautions are not taken the SMARTBOW Wallpoint may be damaged.

Do not use the SMARTBOW Wallpoint under adverse environmental conditions such as

inflammable gases, vapours and solvents

strong vibrations

Page 10 of 32

An operation under the conditions described above may damage the SMARTBOW Wallpoint.

Prior to cleaning the SMARTBOW Wallpoints, disconnect it completely from the power supply (e.g.

network cable). Use a soft, non-lining cloth to clean the product. Never use chemical cleaning agents

such as alcohol, acetone or diluents for cellulose lacquers.

3.5 Operation

In some countries there are laws about digital positioning and tracking of people, animals and/or objects.

Only the user is responsible not to violate such laws or regulations.

Before you start processing the SMARTBOWWallpoint mechanically and/or thermally or before you

disassemble it, be sure to read and pay special attention to the chapter 9 “Waste disposal”.

Depending on the function, the SMARTBOW Wallpoint can produce an elevated level of electromagnetic

radiation, which is within the range of the legal standards. Considering that unborn babies require increased

protection, pregnant women must be protected by appropriate measures. Persons with pacemakers may

also be exposed to risks from electromagnetic radiation. The employer/operator must evaluate workplaces

where there is a special risk of exposure to radiation and if necessary, take measures to avoid the potential

danger.

Should a fire occur, the SMARTBOW Wallpoint may release hazardous substances (gases, fluids, etc.)

that can cause health problems. Therefore, suitable measures must be taken, e.g. protective masks and

protective clothing must be worn.

3.6 Repair and Service

Adjustments, replacement of parts and repair may be performed only by electrical experts authorized by

SMARTBOW. Only original parts may be used for replacing parts. A safety test must always be

performed after parts have been replaced (visual inspection, functional test). This helps to ensure the

continued safety of the SMARTBOWWallpoint.

3.7 Transport

The packaging of the SMARTBOW Wallpoint protects the housing from damage.

If you have to return a SMARTBOW Wallpoint to Smartbow GmbH, it should be packed so that external

influences cannot cause damage to the product.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung