Smartec STC-IP2571A Bedienungsanleitung
Smartec STC-IP2571A / 3570A
www.smartec-security.eu
Firmware User manual
Vandal Proof Dome IP Camera
Table of Contents
1. INSTALLATION _______________________________________________ 1-1
1.1 Minimum System Requirements ___________________________________ 1-1
1.2 Preparation before setup _________________________________________ 1-2
1.2.1 Setup your PC network ________________________________________________ 1-2
1.3 Configuring the IP device_________________________________________ 1-7
1.3.1 Video Display _______________________________________________________ 1-9
1.3.2 Host Setting________________________________________________________ 1-10
1.3.3 WAN Setting _______________________________________________________ 1-13
1.3.4 Date Setting________________________________________________________ 1-16
1.3.5 Video Setting_______________________________________________________ 1-18
1.3.6 Event Setting _______________________________________________________ 1-24
1.3.7 Video Adjustment ___________________________________________________ 1-26
1.3.8 User Account Management ____________________________________________ 1-28
1.3.9 System Info ________________________________________________________ 1-29
1.3.10 Firmware Upgrade ________________________________________________ 1-31
1.3.11 Factory Default___________________________________________________ 1-33
1.3.12 Save Reboot _____________________________________________________ 1-34
1.3.13 Logout__________________________________________________________ 1-35
1-1
1. INSTALLATION
1.1 Minimum System Requirements
CPU
Pentinum 4 2.4GHz and above
Hard Disk 40 GB or above
Memory 256 MB or above
Operating System Windows XP with SP2 or above / Windows 2000 with SP4 or
above
Video Resolution SVGA or XGA with 1024x768 resolution
1
1-2
1.2 Preparation before setup
To configure your IP device, you have to use the Internet Explorer to login
the IP device. Before that, your PC’s networks settings and the IP device’s
IP address must be setup. Make sure all the connections are connected
correctly, and then follow the procedures below to setup.
1. Setup your PC network
You have to match your PC’s TCP/IP setting with the IP device’s
default settings before you can use IE browser to login it. This section
tells you how to setup your PC’s TCP/IP settings.
2. Setup IP device’s IP address
This IP device’s IP address can be setup manually or automatically by
network service (DHCP).
1.2.1 Setup your PC network
To set up the network of IP device via a PC, you have to change the TCP/IP
settings of the PC.
The following are the default network settings of IP device.
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
To access the IP device, the IP address of the PC should match the address
below.
IP Address: 192.168.0.xxx
Subnet Mask: 255.255.255.0
The procedures below is the setup procedure of a PC using Windows XP as
its OS. When running an OS other than Windows XP, please refer to the
manual included with the OS.
zSTEP1
Start up your PC.
zSTEP2
NOTE: xxx should be a number from 1 to 254, but 100 is excepted.
1-3
Click the [Start] and select the "Control Panel"
1-4
zSTEP3
Double-click the "Network and Internet connections" icon.
zSTEP4
Double-click the "Network connections" icon
1-5
zSTEP5
Click “Local Area Connections”, and then click “Change settings of
this connection” in the network Task menu.
zSTEP6
Click “Internet Protocol (TCP/IP)”, and then click the [Properties]
button.
1-6
zSTEP7
Click the “Use the following IP address” radio button and enter the IP
address and the subnet mask.
zSTEP8
Click the [OK] button and the window dialog box closes.
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 100 is
excepted.)
1-7
1.3 Configuring the IP device
This section describes how to configure the IP device. The product
administrator has unlimited access to all setup windows and normal users
can only watch the live image. The IP device is configured under a
standard browser (Microsoft Internet Explorer 6.0 or above).
Follow the procedures below to configure the IP device.
zSTEP1: Open a browser
zSTEP2: Enter the IP address of the IP device.
The default IP address is “192.168.0.100”
The “Login Page” is now displayed as below.
zSTEP3: Enter the Account name (factory default: Admin) and the
Password (factory default: 123456).
z
STEP4: Select the language of the IP device user interface. You can
select from English, Traditional Chinese, Simplified Chinese, Japanese
and Spanish. This user interface setting will disappear once you log out,
if you want to change the default user interface language, please
change the setting of [Host setting] after login successed.
z
STEP5: Click the button to login or click the button
to re-enter again.
1-8
Once successfully login, the “Main Setup page” will be displayed as
below.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Smartec IP-Kamera Handbücher
