SmartRG SR655ac Bedienungsanleitung

Quick Start Guide

SR655ac

This Quick Start Guide shows you how to set up and start using your new gateway.

Installation

Locate the splitter cable that is included with your SmartRG gateway. It has three ports.

1. Connect the splitter as follows:

a. Connect the DSL port of the gateway and the Modem port of the splitter with a telephone cable

b. Connect the phone to the Phone port of the splitter with a telephone cable

c. Connect the incoming line to the Line port of the splitter.

2. Connect a LAN port of the gateway to the network card of the PC using an Ethernet cable.

3. Plug the power adapter to the wall outlet and then connect the other end of it to the Power port of the

gateway.

4. Turn on the unit by pressing the On/Off button on the side of the gateway.

Note: If you use 3G WAN service, connect the 3G USB data card to the USB port of the gateway. If you use the Ethernet

uplink, connect to the WAN interface using an Ethernet cable. You cannot use the xDSL uplink, 3G WAN service, and

Ethernet uplink at the same time.

Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to

complete before you can begin using your Internet applications (browser, email, etc.). If you are unable to connect to the

Internet, confirm that all cable connections are in place and the gateway’s power is turned on.

WAN

RJ11

DSL USB

RESET

DC/

LAN 1-4PHONE 1

USB Data

Card / LTE

On/Off

RJ45

PHONE 2

Phone 1

Phone 2

LED Indicators

The indicator lights (LEDs) on the front of your SR655ac gateway

can help you understand the state of your gateway.

Legend: Green Green Blinking Red Lt. Blue Lt. Blue Blinking Dk Blue Dk. Blue Blinking

LED Action Explanation

All LEDs

except

those listed below Feature enabled &/or working correctly

Data being transferred

POWER Unit is booting up & preparing for use. When the unit is ready, the light changes to green.

Device powered on and ready for use

LED Action Explanation

DSL For VDSL only /WAN service

(Single Line -

Inner or Outer Pair)

For VDSL only WAN service (Bonded Line)

DSL line

acquiring sync

DSL line

(inner pair) connected DSL Line 0 (Inner pair) is active; DSL line 1 (Outer pair) is not

active.

DSL line

(outer pair) acquiring sync and

connected

DSL Line 1 (Outer pair) is active; DSL line 0 (Inner pair) is not

active

DSL connected Both DSL lines connected

DSL down By default, this LED will blink when the DSL connection goes

down. You can modify this setting on the Advanced Settings >

DSL page.

Not lit No lines connected

Note: This LEDmay flash green briefly on startup.

INTERNET DSL sync acquired and gateway on line

Data being transferred

Internet authentication / connection has failed

Quick Gateway Configuration

Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small

circular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into the

hole, press the Reset button gently for 1 second, and then release the button. The system reboots and returns to the

factory defaults.

Logging in to your gateway

To change the settings on your gateway, you must log in the gateway's interface. Make sure that you have completed the

steps in "Installation" before you begin.

1. Open your internet browser application and type 192.168.1.1 into the address line.

2. The login dialog appears. Enter the factory default credentials shown below and click OK.

User Name: admin Password: admin

Note: Your service provider may use other settings. Contact your provider for details.

3. At the bottom of the page, click Manage gateway (advanced). The gateway interface appears, showing the Device

Info summary page.

Configuring the WAN manually

If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer 2 Interface and WAN Services

sections of the SmartRG SR655ac Gateway User Manual to manually establish a connection.

WiFi Setup

Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow the

instructions for the applicable method.

1. In the left navigation bar, click Wireless. The Basic page appears, showing information for the 5 GHz band. If you

want to set up the 2.4 GHz band, click 2.4 GHz Band in the left menu.

2. Click Enable Wireless.

3. If desired, in the SSID field, enter the network name to which you want your client devices connected. Continue

with the steps for the method you prefer.

WPS Method

If the device you wish to connect to the Internet via your gateway supports the WPS secure WiFi connection method, follow

these steps.

1. In the left navigation bar, click Wireless. Then click Security for the wireless band that you want to configure.

2. Select Enable WPS and click Apply/Save to commit your selection.

3. Within 2 minutes, activate WPS on the 3rd party device to which you wish to connect. The device may have a

pushbutton on its exterior or a software interface is used to initiate WPS connection. To learn how to use the WPS

feature on your client device, refer to its documentation.

Your device should now be connected to your gateway wirelessly using WPS. If you encounter problems with the WPS setup

such as connection failure, refer to your client device for further instructions.

Manual Method

Set up your gateway’s parameters first, then follow these steps.

1. In the left navigation bar, click Wireless and then click Security for the wireless band that you want to configure.

2. Scroll down to the Manual Setup AP section.

3. If your gateway supports multiple wireless networks, select the SSID of the network you wish to configure. You will

need this ID for step 8.

4. Select the desired Network Authentication. Make sure that the host devices you intend to use support the

selected authentication type.

5. Choose a WPA Passphrase and type it in to this field. You will need this passphrase for step 8.

6. Select any desired encryption preferences in the lower three fields.

7. Click Apply / Save.

8. On the left side of the gateway, press the 2.4 GHz button and hold for 4-6 seconds. This enables WPS on the

gateway.

9. Follow the WiFi connection instructions provided with your client device to connect to the gateway. Use the SSID

name you selected in Step 2. Then enter the passphrase that you entered in step 4 in the appropriate location on

the network setup screen of your WiFi client device.

Inhaltsverzeichnis

Andere SmartRG Netzwerk-Router Handbücher

SmartRG

SmartRG SR506n Bedienungsanleitung

SmartRG

SmartRG SR505n Bedienungsanleitung

SmartRG

SmartRG SR515ac Bedienungsanleitung

SmartRG

SmartRG SR310N Bedienungsanleitung

SmartRG

SmartRG SR616ac Bedienungsanleitung

SmartRG

SmartRG SR510n Bedienungsanleitung

SmartRG

SmartRG DB120-WL Bedienungsanleitung

SmartRG

SmartRG SR505n Bedienungsanleitung

SmartRG

SmartRG SR630N Bedienungsanleitung

SmartRG

SmartRG SR512nm Bedienungsanleitung

SmartRG

SmartRG SR320n Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise