SMC Networks EZ Connect SMC2670W Bedienungsanleitung

SMC2670W

Information furnished by SMC Networks.(SMC) is believed

to be accurate and reliable. However, no responsibility is

assumed by SMC for its use, nor for any infringements of

patents or other rights of third parties, which may result from

its use. No license is granted by implication or otherwise under

any patent or patent rights of SMC. SMC reserves the right to

change specifications at any time without notice.

SMC Networks

Trademarks

SMC is a registered trademark; and EZ Connect is a trademark

of SMC Networks, Inc. Other product and company names are

trademarks or registered trademarks of their respective holders.

Compliances

FCC Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio com-

munications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the

interference by one of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

•Consultthe dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly

approved by the party responsible for compliance could void

the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

IMPORTANT NOTE

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits

set forth for an uncontrolled environment.This equipment

should be installed and operated with minimum distance

20cm between the radiator & your body.

This transmitter must not be co-located or operating in con-

junction with any other antenna or transmitter.

Industry Canada - Class B

This digital apparatus does not exceed the Class B limits for

radio noise emissions from digital apparatus as set out in the

interference-causing equipment standard entitled “Digital

Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits

radioélectriques applicables aux appareils numériques de

Classe B prescrites dans la norme sur le matérial brouilleur:

“Appareils Numériques,” NMB-003 édictée par l’Industrie.

Congratulations on your purchase of the EZ Connect™ 2.4GHz

11 Mbps Wireless Ethernet Adapter.The EZ Connect™ Wireless

Ethernet Adapter is the perfect device for connecting any

Ethernet enabled device, such as a printer or game console, to

your wireless network. Plug and Play installation allows users

to set-up this adapter to connect to any existing 802.11b

wireless network in minutes. By offering both a windows-based

and web-based administration utility, the EZ Connect Wireless

Adapter can be managed from any PC on your network.To

secure this wireless connection, the EZ Connect Wireless

Ethernet Adapter supports 64/128-bit Wired Equivalent Privacy

(WEP) encryption. For setup instructions, see section 3.

Benefits:

•IEEE 802.11b compliant ensure seamless interoperability

among multiple vendors

•11 Mbps performance meets most foreseeable

networking needs

•Perfectforconnecting network-enabled game console systems.

•64/128-bit WEP ensures secure network connection

•Simple and easy installation by using the convenient web

or windows-based configuration utility.

Compatibility:

•IEEE 802.3

•IEEE 802.11b

The EZ Connect Wireless Ethernet Adapter package

includes the following:

•OneEZConnect™ 2.4GHz 11 Mbps Wireless

Ethernet Adapter

•One CD containing EZ Installation Wizard, Utility

Software and Complete Documentation

•OnePower Adapter

•One CAT 5 Crossover Cable

•OneManual

Minimum Requirements:

•An A/C power outlet (100 – 120V, 50 – 60Hz), to supply

power to the Wireless Ethernet Adapter.

•Anavailable RJ-45 port on a 10BASE-T Ethernet device.

•802.11 compliant wireless Ethernet adapters with TCP/IP

compatible protocol installed.

Section 1 | Getting Started

Site Location

Choose a location for your EZ Connect Wireless Ethernet

Adapter. Usually, the best location is at the center of your

wireless coverage area, and if possible within line-of-sight of

your main wireless broadcast device, such as an Access Point

or a Wireless Router.

Connect the Ethernet Cable

The EZ Connect Wireless Ethernet Adapter can be connected

to any device that has a standard Ethernet connection. Use a

standard Category 5 UTP Crossover Ethernet cable with an RJ-

45 connector to connect the Wireless Ethernet Adapter to any

Ethernet-enabled device.

Note: Do not connect this adapter directly to the LAN

port of a router, such as the Barricade.

Connect the Power Cable

Connect the power adapter cable to the 5V DC power socket

on the rear panel.

Warning: Use only the power adapter supplied with the

SMC2670W. Using another power adapter will cause

damage to the unit and void the warranty.

Antenna

Indicator Lights:

• Power

• Wireless Transmit/Receive

• Ethernet Link/Acivity

1.1 | Wireless Ethernet Adapter LED Indicators

The preceding diagram shows the location of all ports, jacks,

controls, and LED indicator lights on the EZ Connect 11 Mbps

Wireless Ethernet Adapter. The Wireless Ethernet Adapter

contains 1 external antenna, which is adjustable for best

wireless reception.

The front of the Wireless Ethernet Adapter has 3 labeled indi-

cator lights.When you connect your Wireless Ethernet Adapter,

these lights will be on, off, or blinking, indicating the following

states.

Light On Off Blinking

LNK/ACT Ethernet Connection No Ethernet Data being sent or

Connection received over

Ethernet

TX/RX Wireless Connection No Wireless Scanning for

Connection wireless signal

PWR Receiving Power Not Receiving N/A

Power

1.2 | Resetting the Wireless Ethernet Adapter

To reset the SMC2670W Wireless Ethernet Adapter or to correct

temporary connectivity problems, follow the steps outlined

below:

1. Locate the [Default] button on the back of the EZ Connect

Wireless Ethernet Adapter.

2. Unplug the power from the back of the Wireless Ethernet

Adapter for 5 seconds.

3. Hold down the [Default] button, located on the back of

the device.

4. Plug the power connector into the Wireless Ethernet

Adapter while holding down the [Default] button.

5. Release the [Default] button after 3 seconds.

6. Wait another 3 seconds, and then push and hold down the

[Default] button again.

7. The "LNK/ACT" and "TX/RX" LED indicators will blink once

per second about 10-12 times.

8. When the LED indicators begin flashing rapidly, release the

[Default] button.

Andere Handbücher für EZ Connect SMC2670W

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SMC Networks Adapter Handbücher

SMC Networks

SMC Networks 2862W-G Bedienungsanleitung

SMC Networks

SMC Networks EZ Networking SMC2208USB/ETH Bedienungsanleitung

SMC Networks

SMC Networks EZ Connect SMC2602W Bedienungsanleitung

SMC Networks

SMC Networks WCB-GM - annexe 2 Bedienungsanleitung

SMC Networks

SMC Networks SMC EZ Connect Wireless Bluetooth USB Adapter... Bedienungsanleitung

SMC Networks

SMC Networks 1255TX-2 - annexe 1 Bedienungsanleitung

SMC Networks

SMC Networks HPAV-ETH - FICHE TECHNIQUE Bedienungs- und Sicherheitshinweise

SMC Networks

SMC Networks SMCHT-ETH Bedienungsanleitung

SMC Networks

SMC Networks SMC EZ Connect N Pro Draft 11n Wireless CardBus Adapter... Bedienungsanleitung

SMC Networks

SMC Networks SMCHPAVH-ETH Bedienungsanleitung

SMC Networks

SMC Networks SMCWUSB-N Bedienungsanleitung

SMC Networks

SMC Networks EZ Connect Powerline SMCHPAV-ETH2 Bedienungsanleitung

SMC Networks

SMC Networks SMCHPAVH-ETH Bedienungsanleitung

SMC Networks

SMC Networks SMCWAA-B Bedienungsanleitung

SMC Networks

SMC Networks FieldServer FS-8700-16 BACnet PTP Versionshinweis

SMC Networks

SMC Networks SMCWCB-G Bedienungsanleitung

SMC Networks

SMC Networks EZ Connect G SMC2835W Bedienungsanleitung

SMC Networks

SMC Networks HP1D-USB Bedienungsanleitung

SMC Networks

SMC Networks WUSBS-N2 FICHE Bedienungsanleitung

SMC Networks

SMC Networks SMC2862W-G EZ Connect Bedienungsanleitung

SMC Networks

SMC Networks EZ Connect SMC2662W Bedienungsanleitung

SMC Networks

SMC Networks SMCWAPS-G Bedienungsanleitung

SMC Networks

SMC Networks WUSB-N2 Bedienungsanleitung

SMC Networks

SMC Networks HP1D-USB Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung