SMC Networks FS26 Bedienungsanleitung

INSTALLATION GUIDE

EZ SwitchTM 10/100

24-Port Fast Ethernet Switch with 2

Gigabit uplinks

SMCFS26

20 Mason

Irvine, CA 92618

Phone: (949) 679-8000

EZ Switch 10/100

Installation Guide

From SMC’s EZ line of low-cost workgroup LAN solutions

May 2007

Pub. # 150200062500A

E052007-AP-R01

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and

reliable. However, no responsibility is assumed by SMC for its use, nor for any

infringements of patents or other rights of third parties which may result from its use. No

license is granted by implication or otherwise under any patent or patent rights of SMC.

SMC reserves the right to change specifications at any time without notice.

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

Trademarks:

SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are

trademarks of SMC Networks, Inc. Other product and company names are trademarks or

registered trademarks of their respective holders.

Limited Warranty

Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be

free from defects in workmanship and materials, under normal use and service, for the

applicable warranty term. All SMC products carry a standard 90-day limited warranty from

the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion,

repair or replace any product not operating as warranted with a similar or functionally

equivalent product, during the applicable warranty term. SMC will endeavor to repair or

replace any product returned under warranty within 30 days of receipt of the product.

The standard limited warranty can be upgraded to a Limited Lifetime* warranty by

registering new products within 30 days of purchase from SMC or its Authorized Reseller.

Registration can be accomplished via the enclosed product registration card or online via

the SMC Web site. Failure to register will not affect the standard limited warranty. The

Limited Lifetime warranty covers a product during the Life of that Product, which is

defined as the period of time during which the product is an “Active” SMC product. A

product is considered to be “Active” while it is listed on the current SMC price list. As new

technologies emerge, older technologies become obsolete and SMC will, at its discretion,

replace an older product in its product line with one that incorporates these newer

technologies. At that point, the obsolete product is discontinued and is no longer an

“Active” SMC product. A list of discontinued products with their respective dates of

discontinuance can be found at:

http://www.smc.com/index.cfm?action=customer_service_warranty.

All products that are replaced become the property of SMC. Replacement products may

be either new or reconditioned. Any replaced or repaired product carries either a 30-day

limited warranty or the remainder of the initial warranty, whichever is longer. SMC is not

responsible for any custom software or firmware, configuration information, or memory

data of Customer contained in, stored on, or integrated with any products returned to

SMC pursuant to any warranty. Products returned to SMC should have any

customer-installed accessory or add-on components, such as expansion modules,

removed prior to returning the product for replacement. SMC is not responsible for these

items if they are returned with the product.

Customers must contact SMC for a Return Material Authorization number prior to

returning any product to SMC. Proof of purchase may be required. Any product returned

to SMC without a valid Return Material Authorization (RMA) number clearly marked on

the outside of the package will be returned to customer at customer’s expense. For

warranty claims within North America, please call our toll-free customer support number

at (800) 762-4968. Customers are responsible for all shipping charges from their facility to

SMC. SMC is responsible for return shipping charges from SMC to customer.

WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR

REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE

FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF

ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN

FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING

WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER

PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE

SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL

NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION

DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS

CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT,

IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR,

OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY

ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR

TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR

FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS

ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS

PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR

THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,

WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL

BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.

* SMC will provide warranty service for one year following discontinuance from the active

SMC price list. Under the limited lifetime warranty, internal and external power supplies,

fans, and cables are covered by a standard one-year warranty from date of purchase.

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

iii

EMI Certification

FCC Class A

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

You are cautioned that changes or modifications not expressly approved by the

party responsible for compliance could void your authority to operate the equipment

You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or

better for 10 Mbps connections, Category 5 or better for 100 Mbps connections,

Category 5, 5e, or 6 for 1000 Mbps connections.

CE Mark Declaration of Conformance for EMI and Safety (EEC)

This information technology equipment complies with the requirements of the

Council Directive 89/336/EEC on the Approximation of the laws of the Member

States relating to Electromagnetic Compatibility and 73/23/EEC for electrical

equipment used within certain voltage limits and the Amendment Directive 93/68/

EEC. For the evaluation of the compliance with these Directives, the following

standards were applied:

Warning! Do not plug a phone jack connector in the RJ-45 port. This may damage

the device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!

Australia AS/NZS 3548 (1995) - Class A

RFI

Emission: • Limit class A according to EN 55022:1998

• Limit class A for harmonic current emission according to

EN 61000-3-2/1995

• Limitation of voltage fluctuation and flicker in low-voltage

supply system according to EN 61000-3-3/1995

Immunity: • Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to

EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4:1995

(AC/DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by

radio-frequency fields: EN 61000-4-6:1996

(0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations

immunity test according to EN 61000-4-11:1994

(>95% Reduction @10 ms, 30% Reduction @500 ms, >95%

Reduction @5000 ms)

LVD: • EN 60950-1

N11846

Safety Compliance

Please read the following safety information carefully before

installing the switch:

Veuillez lire à fond l'information de la sécurité suivante avant

d'installer le Switch:

AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un

personnel qualifié.

• Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il

n'y a pas de connexion de mise à la terre (mise à la masse).

• Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de

respecter les normes internationales de sécurité.

• Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit

respecter une configuration qui permet un branchement sur une entrée d’appareil

EN 60320/IEC 320.

• La prise secteur doit se trouver à proximité de l’appareil et son accès doit être

facile. Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon

électrique au niveau de cette prise.

Power Cord Set

U.S.A. andCanada The cord setmustbe UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least 10 A

Theattachmentplugmustbeanearth-groundingtypewithNEMA5-15P(15A,

125 V) or NEMA 6-15P (15 A, 250 V) configuration.

Denmark ThesupplyplugmustcomplywithSection107-2-D1,StandardDK2-1aorDK2-

5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. Thesupplyplug mustcomply withBS1363 (3-pin13 A)and befittedwitha5A

fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

Europe The supply plug must comply with CEE7/7 (“SCHUKO”).

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

• L’appareil fonctionne à une tension extrêmement basse de sécurité qui est

conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si

l’équipement auquel il est raccordé fonctionne dans les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos

alimentations sont du type impédance à la terre, ce groupe doit être alimenté par

une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport

1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec

raccordement direct à la terre (masse).

Bitte unbedingt vor dem Einbauen des Switches die folgenden

Sicherheitsanweisungen durchlesen:

WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal

erfolgen.

• Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen

werden.

• Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche die

internationalen Sicherheitsnormen erfüllt.

• DerGerätestecker (derAnschluß andasGerät,nichtderWandsteckdosenstecker)muß

einen gemäß EN 60320/IEC 320 konfigurierten Geräteeingang haben.

Cordon électrique - Il doit être agréé dans le pays d’utilisation

Etats-Unis et

Canada: Le cordon doit avoir reçu l’homologation des UL et un certificat de la

CSA.

Lesspécificationsminimales pourun cableflexible sontAWG No.18,

ou AWG No. 16 pour un cable de longueur inférieure à 2 métres.

- type SV ou SJ

- 3 conducteurs

Le cordon doit être en mesure d’acheminer un courant nominal d’au

moins 10 A.

La prise femelle de branchement doit être du type à mise à la terre

(mise à la masse) et respecter la configuration NEMA 5-15P (15 A,

125 V) ou NEMA 6-15P (15 A, 250 V).

Danemark: La prise mâle d’alimentation doit respecter la section 107-2 D1 de la

norme DK2 1a ou DK2 5a.

Suisse: La prise mâle d’alimentation doit respecter la norme SEV/ASE 1011.

Europe La prise secteur doit être conforme aux normes CEE 7/7 (“SCHUKO”)

LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit

être de type HO3VVF3GO.75 (minimum).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SMC Networks Netzwerk-Router Handbücher

SMC Networks

SMC Networks SMC-EZ1026DT Bedienungsanleitung

SMC Networks

SMC Networks TigerSwitch 100 SMC6924VF Programmierhandbuch

SMC Networks

SMC Networks SMC Barricade SMCBR24Q Bedienungsanleitung

SMC Networks

SMC Networks EZ Connect SMC2870W Bedienungsanleitung

SMC Networks

SMC Networks Barricade SMCWGBR14-N Bedienungsanleitung

SMC Networks

SMC Networks Barricade Cable/DSL Router Bedienungsanleitung

SMC Networks

SMC Networks Barricade SMC7401BRA Bedienungsanleitung

SMC Networks

SMC Networks ADSL2 Barricade N Pro SMC7904WBRA-N Bedienungsanleitung

SMC Networks

SMC Networks ADSL2 Barricade SMC7904BRA3 Bedienungs- und Sicherheitshinweise

SMC Networks

SMC Networks SMC108DT Bedienungsanleitung

SMC Networks

SMC Networks SMCGS10P-Smart Bedienungsanleitung

SMC Networks

SMC Networks EZ Connect SMC7003ADSL Bedienungsanleitung

SMC Networks

SMC Networks Barricade SMC7404WBRA EU Bedienungsanleitung

SMC Networks

SMC Networks Barricade SMC7904BRA2 Bedienungsanleitung

SMC Networks

SMC Networks ADSL2 Barricade SMC7904BRA3 Bedienungsanleitung

SMC Networks

SMC Networks Barricade SMC7401BRA Bedienungsanleitung

SMC Networks

SMC Networks TigerSwitch 10/100 SMC6724L2 Bedienungsanleitung

SMC Networks

SMC Networks 7204BRB Bedienungsanleitung

SMC Networks

SMC Networks Barricade SMC7004ABR Bedienungsanleitung

SMC Networks

SMC Networks EZ Switch SMCGS1601P Bedienungsanleitung

SMC Networks

SMC Networks Barricade SMC7904BRA Bedienungsanleitung

SMC Networks

SMC Networks 48-Port Bedienungsanleitung

SMC Networks

SMC Networks TigerSwitch SMC6709FL2 Bedienungsanleitung

SMC Networks

SMC Networks SMC8606T Programmierhandbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise