SMC Networks EX9-OET1 Bedienungsanleitung

No.EX※※-OMH0025-C

PRODUCT NAME

Output block / Power block

MODEL / Series / Product Number

EX9-OET1

EX9-OET2

EX9-OEP1

EX9-OEP2

EX9-PE1

-1-

No.EX※※-OMH0025-C

Table of Contents

Safety Instructions 2

Model Indication and How to Order 8

Product Outline 8

Summary of Product elements 9

Product Selection 11

Selection for low wattage and high wattage load 11

EX9-OET(Output block for low wattage load) 13

EX9-OEP(Output block for high wattage load) 14

Polarity 15

The number of connected stations 15

Limit of output points when the Output block for high wattage load

and Power block are used 16

Supply current 19

Connection of inductive load 28

Mounting and Installation 29

Mounting 29

Installation 29

Wiring 30

LED Indication 40

Maintenance 41

Troubleshooting 42

Specification 43

Specifications 43

Dimensions 45

Accessories 49

-2-

No.EX※※-OMH0025-C

Safety Instructions

These safety instructions are intended to prevent hazardous situations and/or equipment damage.

These instructions indicate thelevel ofpotential hazard with the labels of "Caution", "Warning" or "Danger".

They are all important notes for safety and must be followed in addition to International Standards

(ISO/IEC)*1), and other safety regulations.

*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems.

ISO 4413: Hydraulic fluid power -- General rules relating to systems.

IEC 60204-1: Safety of machinery -- Electrical equipment of machines. (Part 1: General requirements)

ISO 10218: Manipulating industrial robots -Safety.

etc.

Caution

Caution indicates a hazard with a low level of risk which, if not avoided, could

result in minor or moderate injury.

Warning

Warning indicates a hazard with a medium level of risk which, if not avoided,

could result in death or serious injury.

Danger

Danger indicates a hazard with a high level of risk which, if not avoided, will

result in death or serious injury.

Warning

1. The compatibility of the product is the responsibility of the person who designs the

equipment or decides its specifications.

Since the product specified here is used under various operating conditions, its compatibility with specific

equipment must be decided by the person who designs the equipment or decides its specifications

based on necessary analysis and test results.

The expected performance and safety assurance of the equipment will be the responsibility of the person

who has determined its compatibility with the product.

This person should also continuously review all specifications of the product referring to its latest catalog

information, with a view to giving due consideration to any possibility of equipment failure when

configuring the equipment.

2. Only personnel with appropriate training should operate machinery and equipment.

The product specified here may become unsafe if handled incorrectly.

The assembly, operation and maintenance of machines or equipment including our products must be

performed by an operator who is appropriately trained and experienced.

3. Do not service or attempt to remove product and machinery/equipment until safety is

confirmed.

1. The inspection and maintenance of machinery/equipment should only be performed after measures to

prevent falling or runaway of the driven objects have been confirmed.

2. When the product is to be removed, confirm that the safety measures as mentioned above are

implemented and the power from any appropriate source is cut, and read and understand the specific

product precautions of all relevant products carefully.

3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.

4. Contact SMC beforehand and take special consideration of safety measures if the

product is to be used in any of the following conditions.

1. Conditions and environments outside of the given specifications, or use outdoors or in a place

exposed to direct sunlight.

2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,

vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and

beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or

other applications unsuitable for the standard specifications described in the product catalog.

3. An application which could have negative effects on people, property, or animals requiring special

safety analysis.

4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using

a mechanical protective function, and periodical checks to confirm proper operation.

-3-

No.EX※※-OMH0025-C

Safety Instructions

Caution

1.The product is provided for use in manufacturing industries.

The product herein described is basically provided for peaceful use in manufacturing industries.

If considering using the product in other industries, consult SMC beforehand and exchange

specifications or a contract if necessary.

If anything is unclear, contact your nearest sales branch.

Limited warranty and Disclaimer/Compliance Requirements

The product used is subject to the following "Limited warranty and Disclaimer" and "Compliance

Requirements".

Read and accept them before using the product.

Limited warranty and Disclaimer

1. The warranty period of the product is 1 year in service or 1.5 years after the product is

delivered, whichever is first.2)

Also, the product may have specified durability, running distance or replacement parts.

Please consult your nearest sales branch.

2. For any failure or damage reported within the warranty period which is clearly our

responsibility, a replacement product or necessary parts will be provided.

This limited warranty applies only to our product independently, and not to any other

damage incurred due to the failure of the product.

3. Prior to using SMC products, please read and understand the warranty terms and

disclaimers noted in the specified catalog for the particular products.

2) Vacuum pads are excluded from this 1 year warranty.

A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.

Also, even within the warranty period, the wear of a product due to the use of the

vacuum pad or failure due to the deterioration of rubber material are not covered by the

limited warranty.

Compliance Requirements

1. The use of SMC products with production equipment for the manufacture of weapons of

mass destruction (WMD) or any other weapon is strictly prohibited.

2. The exports of SMC products or technology from one country to another are governed by

the relevant security laws and regulation of the countries involved in the transaction. Prior

to the shipment of a SMC product to another country, assure that all local rules governing

that export are known and followed.

-4-

No.EX※※-OMH0025-C

Operator

This operation manual is intended for those who have knowledge of machinery using pneumatic

equipment, and have sufficient knowledge of assembly, operation and maintenance of such

equipment. Only those persons are allowed to perform assembly, operation and maintenance.

Read and understand this operation manual carefully before assembling, operating or providing

maintenance to the product.

■Safety Instructions

Warning

■Do not disassemble, modify (including changing the printed circuit board) or repair.

An injury or failure can result.

■Do not operate the product outside of the specifications.

Do not use for flammable or harmful fluids.

Fire, malfunction, or damage to the product can result.

Verify the specifications before use.

■Do not operate in an atmosphere containing flammable or explosive gases.

Fire or an explosion can result.

This product is not designed to be explosion proof.

■If using the product in an interlocking circuit:

•Provide a double interlocking system, for example a mechanical system.

•Check the product regularly for proper operation.

Otherwise malfunction can result, causing an accident.

■The following instructions must be followed during maintenance:

•Turn off the power supply.

•Stop the air supply, exhaust the residual pressure and verify that the air is released before performing

maintenance.

Otherwise an injury can result.

-5-

No.EX※※-OMH0025-C

Caution

■After maintenance is complete, perform appropriate functional inspections.

Stop operation if the equipment does not function properly.

Safety cannot be assured in the case of unexpected malfunction.

■Provide grounding to assure the noise resistance of the product.

Individual grounding should be provided close to the product with a short cable.

■NOTE

○Follow the instructions given below when designing, selecting and handling the product.

The instructions on design and selection (installation, wiring, environment, adjustment, operation,

maintenance, etc.) described below must also be followed.

Product specifications

•When conformity to UL is required, the SI unit should be used with a UL1310 Class 2 power supply.

•The SI unit is a UL approved product only if they have a mark on the body.

•Use the specified voltage.

Otherwise failure or malfunction can result.

•Reserve a space for maintenance.

Allow sufficient space for maintenance when designing the system.

•Do not remove any nameplates or labels.

This can lead to incorrect maintenance, or misreading of the operation manual, which could cause damage or

malfunction to the product.

It may also result in non-conformity to safety standards.

-6-

No.EX※※-OMH0025-C

Product handling

Installation

•Do not drop, hit or apply excessive shock to the product.

Otherwise damage to the product can result, causing malfunction.

•Tighten to the specified tightening torque.

If the tightening torque is exceeded the mounting screws may be broken.

IP67 protection cannot be guaranteed if the screws are not tightened to the specified torque.

•Never mount a product in a location that will be used as a foothold.

The product may be damaged if excessive force is applied by stepping or climbing onto it.

Wiring

•Avoid repeatedly bending or stretching the cables, or placing heavy load on them.

Repetitive bending stress or tensile stress can cause breakage of the cable.

•Wire correctly.

Incorrect wiring can break the product.

•Do not perform wiring while the power is on.

Otherwise damage to the product and/or I/O device can result, causing malfunction.

•Do not route wires and cables together with power or high voltage cables.

Otherwise the product and/or I/O device can malfunction due to interference of noise and surge voltage from power

and high voltage cables to the signal line.

Route the wires (piping) of the product and/or I/O device separately from power or high voltage cables.

•Confirm proper insulation of wiring.

Poor insulation (interference from another circuit, poor insulation between terminals, etc.) can lead to excess

voltage or current being applied to the product, causing damage.

•Take appropriate measures against noise, such as using a noise filter, when the product is incorporated

into equipment.

Otherwise noise can cause malfunction.

Environment

•Select the proper type of protection according to the environment of operation.

IP67 protection is achieved when the following conditions are met.

(1) The units are connected properly with product cable with M12 connector and power cable with M12 connector.

(2) Suitable mounting of each unit and manifold valve.

If using in an environment that is exposed to water splashes, please take measures such as using a cover.

•Do not use in a place where the product could be splashed by oil or chemicals.

If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even

for a short time, it may be adversely affected (damage, malfunction etc.).

•Do not use the product in an environment where corrosive gases or fluids could be splashed.

Otherwise damage to the product and malfunction can result.

•Do not use in an area where surges are generated.

If there is equipment which generates a large amount of surge (solenoid type lifter, high frequency induction furnace,

motor, etc.) close to the product, this may cause deterioration or breakage of the internal circuit of the product. Avoid

sources of surge generation and crossed lines.

•When a surge-generating load such as a relay or solenoid is driven directly, use an product with a built-in

surge absorbing element.

Direct drive of a load generating surge voltage can damage the product.

•The product is CE marked, but not immune to lightning strikes. Take measures against lightning strikes

in the system.

•Prevent foreign matter such as remnant of wires from entering the product to avoid failure and

malfunction.

-7-

No.EX※※-OMH0025-C

•Mount the product in a place that is not exposed to vibration or impact.

Otherwise failure or malfunction can result.

•Do not use the product in an environment that is exposed to temperature cycle.

Heat cycles other than ordinary changes in temperature can adversely affect the inside of the product.

•Do not expose the product to direct sunlight.

If using in a location directly exposed to sunlight, shade the product from the sunlight.

Otherwise failure or malfunction can result.

•Keep within the specified ambient temperature range.

Otherwise malfunction can result.

•Do not operate close to a heat source, or in a location exposed to radiant heat.

Otherwise malfunction can result.

Adjustment and Operation

•Perform settings suitable for the operating conditions.

Incorrect setting can cause operation failure.

•Please refer to the PLC manufacturer's manual etc. for details of programming and addresses.

For the PLC protocol and programming refer to the relevant manufacturer's documentation.

Maintenance

•Turn off the power supply, stop the supplied air, exhaust the residual pressure and verify the release of

air before performing maintenance.

There is a risk of unexpected malfunction.

•Perform regular maintenance and inspections.

There is a risk of unexpected malfunction.

•After maintenance is complete, perform appropriate functional inspections.

Stop operation if the equipment does not function properly.

Otherwise safety is not assured due to an unexpected malfunction or incorrect operation.

•Do not use solvents such as benzene, thinner etc. to clean the each unit.

They could damage the surface of the body and erase the markings on the body.

Use a soft cloth to remove stains.

For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains

again with a dry cloth.

-8-

No.EX※※-OMH0025-C

Model Indication and How to Order

•Output block

EX9-OE



Output type

Source / PNP (negative common)

Sink / NPN (positive common)

Power supply type

Internal power supply from SI unit (for low wattage load)

External power supply type (for high wattage load) 

: A Power block is required.

•Power block

EX9-PE1

Product Outline

The EX9 series is connected between an applicable SI unit and the valve manifold to operate equipment such

as a solenoid valve or relay. An Output block and Power block are available.

•Output block

Type

Part No.

Description

Remarks

For low

wattage

load

EX9-OET1

EX9-OET2

Current Output to connected load

(output equipment) or manifold valves

using the power supply from the SI unit.

Usable load wattage is limited to 1.5 W because

power is supplied by the SI unit.

When the load is up to 12 W, use both the Power

block and a high wattage load Output block.

For high

wattage

load

EX9-OEP1

EX9-OEP2

Current Output to connected load

(output equipment) using an external

power supply.

For use with the Power block (EX9-PE1) which

uses an external power supply.

: Limited to 1.0 W when the EX500-Q02 SI unit (page 54) is connected.

•Power block

Type

Part No.

Description

Remarks

EX9-PE1

Provides an external power supply to

the Output block for high wattage load.

For use with the Output block for high wattage

load.

-9-

No.EX※※-OMH0025-C

Summary of Product elements

EX9-OET1, EX9-OET2 (Output block for low wattage load)

Element

Function

Indicator LED

Indicates the output status.

Solenoid valve connector

Connected to solenoid valve.

Output connector (No.0)

Connects with output device.

Output connector (No.1)

Connects with output device.

SI unit connector

Connected to SI unit.

EX9-OEP1, EX9-OEP2 (Output block for high wattage load)

Element

Function

Indicator LED

Indicates the output status.

Solenoid valve connector

Connected to solenoid valve.

Output connector (No.0)

Connects with output device.

Output connector (No.1)

Connects with output device.

Power block connector

Connected to Power block.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SMC Networks Aufnahmegeräte Handbücher

SMC Networks

SMC Networks EX600-SPR1 Bedienungsanleitung

SMC Networks

SMC Networks EX180-SDN4 Series Bedienungsanleitung

SMC Networks

SMC Networks EX600 Series Installationshandbuch

SMC Networks

SMC Networks EX260 Series Bedienungsanleitung

SMC Networks

SMC Networks EX250 Series Installationshandbuch

SMC Networks

SMC Networks EX250-SAS Series Bedienungsanleitung

SMC Networks

SMC Networks EX500-GDN1 Bedienungsanleitung

SMC Networks

SMC Networks EX510-GPR1 Series Bedienungsanleitung

SMC Networks

SMC Networks EX260-SPR1 Bedienungsanleitung

SMC Networks

SMC Networks EX250-SDN1 Bedienungsanleitung

SMC Networks

SMC Networks EX120-SCM1 Bedienungsanleitung

SMC Networks

SMC Networks EX600-SEC Series Bedienungsanleitung

SMC Networks

SMC Networks EX250 Series Bedienungsanleitung

SMC Networks

SMC Networks EX510-GPR1 Series Bedienungsanleitung

SMC Networks

SMC Networks EX600-SEN1 Bedienungsanleitung

SMC Networks

SMC Networks EX12-SCM Series Bedienungsanleitung

SMC Networks

SMC Networks EX124U-SDN1-X2 Bedienungsanleitung

SMC Networks

SMC Networks EX260 Series Bedienungsanleitung

SMC Networks

SMC Networks EX260 Series Bedienungsanleitung

SMC Networks

SMC Networks EX120-SDN1-X2 Bedienungsanleitung

SMC Networks

SMC Networks EX180-SMJ3 Series Bedienungsanleitung

SMC Networks

SMC Networks EX250 Series Bedienungsanleitung

SMC Networks

SMC Networks EX500 Series Bedienungsanleitung

SMC Networks

SMC Networks EX260 Series Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch