SMC Networks 8724M INT - annexe 1 Bedienungsanleitung

TigerStack 10/100

24-Port 10/100Mbps

Stackable Managed Switch

Installation Guide

◆24 auto-MDI/MDI-X 10BASE-T/100BASE-TX ports

◆2 Gigabit RJ-45 ports shared with 2 SFP transceiver slots

◆2 Gigabit stacking ports that act as Ethernet ports in

standalone mode

◆Stacks up to 8 units

◆12.8 Gbps of aggregate bandwidth

◆Non-blocking switching architecture

◆Spanning Tree Protocol and Rapid STP

◆Up to four LACP or static 4-port trunks

◆RADIUS and TACACS+ authentication

◆Rate limiting for bandwidth management

◆CoS support for four-level priority

◆Full support for VLANs with GVRP

◆IP Multicasting with IGMP Snooping

Installation Guide

SMC6224M

38 Tesla

Irvine, CA 92618

Phone: (949) 679-8000

TigerStack 10/100

Installation Guide

From SMC’s Tiger line of feature-rich workgroup LAN solutions

October 2004

Pub. # 150000015400H

Information furnished by SMC Networks, Inc. (SMC) is believed to be accu-

rate and reliable. However, no responsibility is assumed by SMC for its use,

nor for any infringements of patents or other rights of third parties which

may result from its use. No license is granted by implication or otherwise

under any patent or patent rights of SMC. SMC reserves the right to change

specifications at any time without notice.

SMC Networks, Inc.

38 Tesla

Irvine, CA 92618

Trademarks:

SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are trademarks of SMC Networks,

Inc. Other product and company names are trademarks or registered trademarks of their respective holders.

IMITED

ARRANTY

Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free

from defects in workmanship and materials, under normal use and service, for the applicable

warranty term. All SMC products carry a standard 90-day limited warranty from the date of

purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace

any product not operating as warranted with a similar or functionally equivalent product, during

the applicable warranty term. SMC will endeavor to repair or replace any product returned under

warranty within 30 days of receipt of the product.

The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering

new products within 30 days of purchase from SMC or its Authorized Reseller. Registration can

be accomplished via the enclosed product registration card or online via the SMC web site.

Failure to register will not affect the standard limited warranty. The Limited Lifetime warranty

covers a product during the Life of that Product, which is defined as the period of time during

which the product is an “Active” SMC product. A product is considered to be “Active” while it is

listed on the current SMC price list. As new technologies emerge, older technologies become

obsolete and SMC will, at its discretion, replace an older product in its product line with one that

incorporates these newer technologies. At that point, the obsolete product is discontinued and is

no longer an “Active” SMC product. A list of discontinued products with their respective dates

of discontinuance can be found at:

http://www.smc.com/index.cfm?action=customer_service_warranty.

All products that are replaced become the property of SMC. Replacement products may be

either new or reconditioned. Any replaced or repaired product carries either a 30-day limited

warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible for

any custom software or firmware, configuration information, or memory data of Customer

contained in, stored on, or integrated with any products returned to SMC pursuant to any

warranty. Products returned to SMC should have any customer-installed accessory or add-on

components, such as expansion modules, removed prior to returning the product for

replacement. SMC is not responsible for these items if they are returned with the product.

Customers must contact SMC for a Return Material Authorization number prior to returning

any product to SMC. Proof of purchase may be required. Any product returned to SMC without

a valid Return Material Authorization (RMA) number clearly marked on the outside of the

package will be returned to customer at customer’s expense. For warranty claims within North

America, please call our toll-free customer support number at (800) 762-4968. Customers are

responsible for all shipping charges from their facility to SMC. SMC is responsible for return

shipping charges from SMC to customer.

IMITED

ARRANTY

WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR

REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE

FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU

OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER

IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING

WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER

PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH

THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC

SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND

EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES

NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE,

NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED

ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE

INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR

TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND,

OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS

ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS

PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR

THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,

WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY

SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.

* SMC will provide warranty service for one year following discontinuance from the active SMC

price list. Under the limited lifetime warranty, internal and external power supplies, fans, and

cables are covered by a standard one-year warranty from date of purchase.

SMC Networks, Inc.

38 Tesla

Irvine, CA 92618

iii

OMPLIANCES

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause interference to radio

communications. It has been tested and found to comply with the limits for a Class A

computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to provide

reasonable protection against such interference when operated in a commercial environment.

Operation of this equipment in a residential area is likely to cause interference, in which case the

user, at his own expense, will be required to take whatever measures may be required to correct

the interference. You are cautioned that changes or modifications not expressly approved by the

party responsible for compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) cable for RJ-45 connections—Category 3 or greater

for 10 Mbps connections, Category 5 for 100 Mbps connections and Category 5, 5e or 6 for

1000 Mbps connections. Use 50/125 or 62.5/125 micron multimode fiber optic cable, or 9/125

micron single-mode cable, for SFP transceiver connections.

Warnings: 1. Wear an anti-static wrist strap or take other suitable measures to prevent elec-

trostatic discharge when handling this equipment.

2. When connecting this switch to a power outlet, connect the field ground lead

on the tri-pole power plug to a valid earth ground line to prevent electrical

hazards.

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,”

ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils

numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils

Numériques,” NMB-003 édictée par le ministère des Communications.

Japan VCCI Class A

OMPLIANCES

CE Mark Declaration of Conformance for EMI and Safety

(EEC)

SMC contact for these products in Europe is:

SMC Networks Europe,

Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí, Barcelona, Spain.

This information technology equipment complies with the requirements of the Council

Directive 89/336/EEC on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain

voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance

with these Directives, the following standards were applied:

Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device.

Les raccordeurs ne sont pas utilisé pour le systéme téléphonique!

RFI Emission:

• Limit class A according to EN 55022:1998

• Limit class A for harmonic current emission according to EN 61000-3-2/

1995

• Limitation of voltage fluctuation and flicker in low-voltage supply system

according to EN 61000-3-3/1995

Immunity:

• Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC

power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by radio-frequency fields:

EN 61000-4-6:1996 (0.15 - 80 MHz with

1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

Reduction @500 ms, >95% Reduction @5000 ms)

LVD:

• EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)

OMPLIANCES

Australia AS/NZS 3548 (1995) - Class A

SMC contact for products in Australia is:

SMC Communications Pty. Ltd.

Suite 18, 12 Tryon Road,

Lindfield NSW2070,

Phone: 61-2-94160437

Fax: 61-2-94160474

Safety Compliance

Warning: Fiber Optic Port Safety

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

Power Cord Safety

Please read the following safety information carefully before installing the switch:

WARNING

Installation and removal of the unit must be carried out by qualified personnel only.

• The unit must be connected to an earthed (grounded) outlet to comply with international

safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without an earth (ground)

connection.

• The appliance coupler (the connector to the unit and not the wall plug) must have a

configuration for mating with an EN 60320/IEC 320 appliance inlet.

• The socket outlet must be near to the unit and easily accessible. You can only remove power

from the unit by disconnecting the power cord from the outlet.

When using a fiber optic port, never look at the transmit laser while

it is powered on. Also, never look directly at the fiber TX port and

fiber cable ends when they are powered on.

Ne regardez jamais le laser tant qu’il est sous tension. Ne regardez

jamais directement le port TX (Transmission) à fibres optiques et les

embouts de câbles à fibres optiques tant qu’ils sont sous tension.

Niemals ein Übertragungslaser betrachten, während dieses

eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß und auf

die Faserkabelenden schauen, während diese eingeschaltet sind.

CLASS I

LASER DEVICE

DISPOSITIF LASER

DE CLASSE I

LASERGER

DER KLASSE I

ÄT

OMPLIANCES

• This unit operates under SELV (Safety Extra Low Voltage) conditions according to

IEC 60950. The conditions are only maintained if the equipment to which it is connected also

operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT

†

supplies. If your supplies are of IT type, this unit must be

labelled Neutral, connected directly to earth (ground).

†

Impédance à la terre

Important!

Before making connections, make sure you have the correct cord set. Check it (read the

label on the cable) against the following:

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least 10 A

The attachment plug must be an earth-grounding type with NEMA

5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

Denmark The supply plug must comply with Section 107-2-D1, Standard

DK2-1a or DK2-5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be fitted

with a 5 A fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and be of

type HO3VVF3GO.75 (minimum).

Europe The supply plug must comply with CEE7/7 (“SCHUKO”).

The mains cord must be <HAR> or <BASEC> marked and be of

type HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SMC Networks Schalten Handbücher

SMC Networks

SMC Networks TigerSwitch SMC6726AL2 Bedienungsanleitung

SMC Networks

SMC Networks TIGERSWITCH 10/100 Bedienungsanleitung

SMC Networks

SMC Networks EZ Networking SMC-EZ108FDT Bedienungsanleitung

SMC Networks

SMC Networks 9712F - FICHE TECHNIQUE Bedienungsanleitung

SMC Networks

SMC Networks TigerStack II SMC8848M Bedienungsanleitung

SMC Networks

SMC Networks IS10M-20-D Bedienungsanleitung

SMC Networks

SMC Networks PF2 Series Bedienungsanleitung

SMC Networks

SMC Networks PF3A801H-L Bedienungsanleitung

SMC Networks

SMC Networks SMCGS50C-SMART - FICHE TECHNIQUE Bedienungs- und Sicherheitshinweise

SMC Networks

SMC Networks EZ Switch SMC-EZ109DT Bedienungsanleitung

SMC Networks

SMC Networks SMC8612XL3 F 1.0.1.3 Bedienungsanleitung

SMC Networks

SMC Networks TigerSwitch 10 Bedienungsanleitung

SMC Networks

SMC Networks TigerSwitch SMC6912M Bedienungsanleitung

SMC Networks

SMC Networks 7824M/FSW - annexe 1 Programmierhandbuch

SMC Networks

SMC Networks 8150L2 Bedienungsanleitung

SMC Networks

SMC Networks TigerSwitch SMC6128PL2 Bedienungsanleitung

SMC Networks

SMC Networks 8748L2 FICHE Programmierhandbuch

SMC Networks

SMC Networks PS1000 Bedienungsanleitung

SMC Networks

SMC Networks SMC EZ Stack 10/100 SMC5216 Bedienungsanleitung

SMC Networks

SMC Networks ZSE40A Bedienungsanleitung

SMC Networks

SMC Networks 3605T-EZ EUR - FICHE TECHNIQUE Bedienungsanleitung

SMC Networks

SMC Networks EZ Connect Bedienungsanleitung

SMC Networks

SMC Networks TigerCard SMC8724M Bedienungsanleitung

SMC Networks

SMC Networks SMC8748ML3 Programmierhandbuch

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung