Smeg A2EA Bedienungsanleitung

Contents

1. INSTRUCTIONS FOR SAFE AND PROPER USE________________ 4

2. INSTALLATION OF THE APPLIANCE_________________________ 6

3. ADAPTATION TO DIFFERENT TYPES OF GAS ________________ 9

4. FINAL OPERATIONS_____________________________________ 11

5. DESCRIPTION OF CONTROLS ____________________________ 13

6. USE OF THE COOKING HOB ______________________________ 18

7. USE OF THE OVENS_____________________________________ 19

8. AVAILABLE ACCESSORIES _______________________________ 21

9. COOKING HINTS________________________________________ 22

10. CLEANING AND MAINTENANCE ___________________________ 28

11. EXTRAORDINARY MAINTENANCE _________________________ 31

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE

IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.

INSTRUCTIONS FOR THE INSTALLER: these are for the qualified

technician who must carry out a suitable check of the gas system,

install the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,

description of the commands and the correct procedures for cleaning

and maintenance of the appliance.

Introduction

1. INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND

THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE

PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE

READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE

USING THE COOKER. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED.

INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN

ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS

INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT

REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY

OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD.

ALL OTHER USES ARE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER

USE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE

THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST

SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED

ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE SOCKET

MUST BE THE SAME TYPE AND MUST CONFORM TO CURRENT

REGULATIONS.

THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN

BUILT IN.

NEVER UNPLUG BY PULLING ON THE CABLE.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION

TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW.

SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE

SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION

(OFF) WHEN YOU FINISH USING THE HOB.

NEVER PUT INFLAMMABLE OBJECTS INTO AN OVEN: IF THEY CATCH FIRE

THEY COULD CAUSE A FIRE IN THE HOME.

Introduction

THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND

BRAND NAME IS POSITIONED VISIBLY IN THE STORAGE COMPARTMENT.

THE PLATE MUST NOT BE REMOVED.

DO NOT INSTALL THIS APPLIANCE ON A RAISED PLATFORM.

DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO

TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.

DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS

ON THE COOKING HOB GRIDS.

DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE

OUTER PERIMETER OF THE HOB.

THE APPLIANCE IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW

CHILDREN TO GO NEAR OR PLAY WITH IT.

THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE

2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

(WEEE).

THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF

RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC

EQUIPMENT.

BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND

PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance or by the use of non-original

spares.

Instructions for the installer

2. INSTALLATION OFTHE APPLIANCE

It is the law that all gas appliances are installed by competent persons.

Corgi gas installers are approved to work to safe and satisfactory

standards. All gas installation, servicing and repair work must be in

accordance with the gas safety regulations 1984 (installation and use) as

amended 1990.

It can be placed against walls higher than the hob as shown in the

drawings A and B relating to the installation classes. Wall units or

extractor hoods located above the hob must be at least 750 mm away

from it.

A B

Slot in Free standing

2.1 Electrical connection

Make sure that the power line voltage matches the specifications

indicated on the rating plate located inside the storage compartment.

This rating plate must never be removed.

The plug at the end of the power cable and the wall socket must be the

same type (conforming to regulations in force). Check that the power line

is adequately grounded. Do not use reducers, adapters or shunts.

On the power line, install an omnipolar cut-off device with contact cut-off

distance greater than or equal to 3 mm, located in an easily accessible

position near the unit.

Instructions for the installer

For operation on 380-415V3N

∼

:use an

H05RR-F-type five-core cable (5 x 1.5 mm2).

For operation on 380-415V2N

∼

:use an

H05RR-F-type four-core cable (4 x 1.5 mm2).

For operation on 220-240V

∼

:use an

H05RR-F-type three-core cable (3 x 2.5 mm2).

The cable end to be connected to the

appliance must be provided with an ground

wire (yellow-green) at least 20 mm longer.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance.

2.2 Ventilation requirements

The room containing the appliance should have an air supply in accordance with

B.S. 5440 part 2 1989.

1. All rooms require an opening window or equivalent, and some rooms will

require a permanent vent as well.

2. For room volumes up to 5 m3an air vent of 100 cm2is required.

3. If the room has a door that opens directly to the outside, and the room

exceeds 1 m3no air vent is required.

4. For room volumes between 5 m3and 10 m3an air vent of 50 cm2is required.

5. If there are other fuel burning appliances in the same room B.S. 5440 part 2

1989 should be consulted to determine the air vent requirements.

6. This appliance must not be installed in a bed sitting room of less than 20 m3

or in a bathroom or shower room.

Windows and permanent vents should therefore not be blocked or removed

without first consulting a Corgi gas installer.

Failure to install appliances correctly is dangerous and could lead to

prosecution.

Instructions for the installer

2.3 Connecting to natural and LPG gas (Please see connection

diagram)

Make the connection to the appliance using flexible bayonet

style hose in accordance to B.S. 669. The hose connection at

the rear of the appliance has a 1/2" BSP internal thread.

Please use seal Cbetween the flexible connection Land the

appliance supply tube B. When making the connection, make

sure that no stress of any kind is applied to the cooker and

that the hose does not touch any sharp edges.

If connecting to LPG the bayonet hose must have red

bands on it.

2.4 Instruction for wall fixing (only on some models)

1) Fix the screw to the wall and hook the chain (B);

2) Hook the chain to the hole positioned at the rear of the cooker by the gas

pipe (A);

3) Once the chain is in position, push the cooker against the wall;

4) The height of the screw hole from floor level must not exceed 800 mm (C).

Instructions for the installer

3. ADAPTATIONTO DIFFERENTTYPES OF GAS

Before performing any cleaning or maintenance work, detach the

appliance from the electrical socket.

The cooker hob is set for natural gas G20 (2H) at a pressure of 20 mbar.

In the case of functioning with other types of gas the burner nozzles must

be changed and the minimum flame adjusted on the gas taps. To change

the nozzles, proceed as described below.

3.1 Replacement of nozzles on the hob

This operation requires no primary air regulation.

1. Extract the grids and remove all the caps and flame-spreader

crowns;

2. unscrew the burner nozzles with a 7 mm socket wrench;

3. replace the nozzles according to the type of gas to be used and the

description in paragraph “3.2 Burner and nozzle characteristics

table”.

Replace the burners in the correct position.

Instructions for the installer

3.2 Burner and nozzle characteristics table

Burner

Rated

heating

capacity

(kW)

LPG –G30/G31 28/37 mbar

Nozzle

diameter

1/100 mm

By-pass

1/100

Reduced

flowrate

(W)

Flowrate

g/h G30

Flowrate

g/h G31

Auxiliary 1.05 50 30 360 76 75

Semi rapid 1.8 65 33 450 131 129

Rapid 3 85 45 750 218 215

Triple crown 3.3 91 68 1600 240 236

Burner

Rated heating

capacity

(kW)

Natural gas – G20 20 mbar

Nozzle

diameter

1/100 mm

Reduced

flowrate

(W)

Auxiliary 1.05 72 360

Semi rapid 1.8 97 450

Rapid 3 115 750

Triple crown 3.5 133 1600

3.3 Arrangement of burners on cooking hob

BURNERS

1Auxiliary

2Semi rapid

3Rapid

4Ultra rapid

5Ultra rapid

Instructions for the installer

4. FINAL OPERATIONS

After replacing the nozzles, reposition the flame-spreader crowns, the

burner caps and the grids.

After adjustment to a different kind of gas from the one for which the

cooker has been tested, replace the plate inside the storage

compartment with one corresponding to the new kind of gas. This plate

can be obtained from your nearest Authorised Assistance Centre.

4.1 Adjustment of minimum for natural gas

Light the burner and take it to the minimum .

Remove the gas tap knob and turn the

adjustment screw inside or at the side of the tap

shaft (depending on the model) until there is a

regular minimum flame. Replace the knob and

check burner flame stability: (rapidly turning the

knob from maximum to minimum position, the

flame should not go out). Repeat the operation on

all the gas taps.

4.2 Regulation of minimum for LPG

To regulate the minimum for LPG, completely tighten (clockwise) the

screw inside or next to the gas tap pin (depending on the model).

The diameters of the by-passes for each burner are given in table “3.2

Burner and nozzle characteristics table”.

4.3 Positioning and levelling of the appliance

Having carried out the electricity and gas hook-up, level the appliance

using the four adjustable legs.

Instructions for the installer

4.4 Mounting the rear top upstand

•Position the upstand above the top, taking care to align holes Awith

holes B.

•Secure the upstand to the top by tightening screws C.

Inhaltsverzeichnis

Andere Smeg Kocher Handbücher

Smeg

Smeg C9CMXA Bedienungsanleitung

Smeg

Smeg TR90 Bedienungsanleitung

Smeg

Smeg Victoria Bedienungsanleitung

Smeg

Smeg CX61VMLS8 Bedienungsanleitung

Smeg

Smeg Classica Concerto SSA92MAA9 Bedienungsanleitung

Smeg

Smeg Victoria TR4110IGR Bedienungsanleitung

Smeg

Smeg CX51VE Bedienungsanleitung

Smeg

Smeg SUK91CMX5 Bedienungsanleitung

Smeg

Smeg TR93BL Bedienungsanleitung

Smeg

Smeg A1C Bedienungsanleitung

Smeg

Smeg Classica C7GPX9 Bedienungsanleitung

Smeg

Smeg TRA90P9 Bedienungsanleitung

Smeg

Smeg Victoria TR103GR Bedienungsanleitung

Smeg

Smeg SUK62MX8 Bedienungsanleitung

Smeg

Smeg CB61VES Bedienungsanleitung

Smeg

Smeg Classica C6GMX9 Bedienungsanleitung

Smeg

Smeg B90GMXI9 Bedienungsanleitung

Smeg

Smeg TR93IP Bedienungsanleitung

Smeg

Smeg FS61XPZ5 Bedienungsanleitung

Smeg

Smeg Classic Bedienungsanleitung

Smeg

Smeg TR90DGM9 Bedienungsanleitung

Smeg

Smeg SYD4110-1 Bedienungsanleitung

Smeg

Smeg Mista CS95GMNNA1 Bedienungsanleitung

Smeg

Smeg cooker Bedienungsanleitung

Beliebte Kocher Handbücher anderer Marken

Modena

Modena FC 7645 SGM Betriebsanleitung

Electrolux

Electrolux Insight EKG6049 Bedienungsanleitung

Stanley

Stanley Donard 60 Bedienungsanleitung

Bartscher

Bartscher 201TC Bedienungsanleitung

Parkinson Cowan

Parkinson Cowan 50 GR/BU Bedienungsanleitung

Siemens

Siemens HK9P00020U Bedienungsanleitung

Creda

Creda S150E Leitfaden

Creda

Creda HB48309 Bedienungsanleitung

Bosch

Bosch HCE743220F Bedienungsanleitung

Tricity Bendix

Tricity Bendix SE545P Bedienungsanleitung

NEFF

NEFF E1461A2/01 Bedienungsanleitung

Zanussi

Zanussi ZCM 700 X Bedienungsanleitung

RiverGrille

RiverGrille TF2002501-RG Bedienungsanleitung

Vollrath

Vollrath 69504F Bedienungsanleitung

Tricity Bendix

Tricity Bendix CSIE500 Bedienungsanleitung

AEG

AEG Competence 5731 V Bedienungsanleitung

Euromaid

Euromaid ES60 Bedienungsanleitung

Hotpoint

Hotpoint HUI 62 TP Bedienungsanleitung