Smeg Electric Multifunction Oven SE290X-6 Bedienungsanleitung

Index

1. PRECAUTIONS FOR SAFETY AND USE _____________________ 29

2. INSTALLATION _________________________________________ 31

3. DESCRIPTION OF CONTROLS ____________________________ 34

4. USING THE OVEN_______________________________________ 40

5. ACCESSORIES AVAILABLE _______________________________ 41

6. COOKING ADVICE ______________________________________ 42

7. CLEANING AND MAINTENANCE ___________________________ 47

8. EXTRAORDINARY MAINTENANCE _________________________ 51

INSTRUCTIONS FOR THE INSTALLER: these are intended for the

qualified engineer who is to install, commission and test the

appliance.

INSTRUCTIONS FOR THE USER: these provide recommendations for

use, a description of the controls and the correct procedures for

cleaning and maintaining the appliance.

Presentation

1. PRECAUTIONS FOR SAFETY AND USE

THIS MANUAL CONSTITUTES AN INTEGRAL PART OF THE APPLIANCE:

TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE

OVEN'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND

ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE OVEN.

INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN

COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS APPLIANCE IS

INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC

DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE IS BUILT TO

PROVIDE THE FOLLOWING FUNCTION: COOKING AND HEATING FOODS;

ALL OTHER USES ARE TO BE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN

THOSE STATED ABOVE.

NEVER LEAVE PACKAGING RESIDUES UNATTENDED IN THE HOME.

SEPARATE THE VARIOUS PACKAGING MATERIALS BY TYPE AND

CONSIGN THEM TO THE NEAREST SEPARATE DISPOSAL CENTRE.

THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH

ELECTRICAL SYSTEM SAFETY REGULATIONS.

IF THE MAIN ELECTRICAL CONNECTION IS TO BE MADE BY MEANS OF A

PLUG AND SOCKET, THEY MUST BOTH BE OF THE SAME TYPE AND MUST

BE CONNECTED TO THE POWER SUPPLY LEAD IN ACCORDANCE WITH

THE RELEVANT REGULATIONS.

THE POWER SUPPLY SOCKET MUST BE ACCESSIBLE EVEN AFTER THE

APPLIANCE HAS BEEN BUILT-IN.

NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY

LEAD.

NEVER OBSTRUCT THE OPENINGS AND SLITS PROVIDED FOR

VENTILATION AND HEAT DISPERSAL.

IMMEDIATELY AFTER INSTALLATION, CARRY OUT A QUICK TEST ON THE

OVEN FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS

MANUAL. IF THE APPLIANCE FAILS TO OPERATE, DISCONNECT IT FROM

THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE

CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.

Presentation

EVER PLACE INFLAMMABLE OBJECTS IN THE OVEN: IF IT SHOULDN

ACCIDENTALLY BE SWITCHED ON, THIS MIGHT CAUSE A FIRE.

THE APPLIANCE BECOMES VERY HOT DURING USE. TAKE CARE NOT TO

TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.

THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND

MARK IS IN A VISIBLE POSITION ON THE OVEN DOOR FRAME.

THE NAMEPLATE MUST NEVER BE REMOVED.

HE APPLIANCE IS INTENDED FOR USE BY ADULTS. KEEP CHILDREN ATT

A SAFE DISTANCE AND NEVER ALLOW THEM TO PLAY WITH IT.

THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC

ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE).

THIS DIRECTIVE CONTAINS THE REGULATIONS GOVERNING THE

COLLECTION AND RECYCLING OF DECOMMISSIONED APPLIANCES

THROUGHOUT THE EUROPEAN UNION.

BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND

PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.

The manufacturer declines all responsibility for injury or damage

caused by failure to comply with the above regulations or deriving from

tampering with even just one part of the appliance and the use of non-

original spare parts.

Instructions for the Installer

2. INSTALLATION

2.1 Electrical connection

Check that the power supply voltage and size are as specified on the

nameplate on the oven door frame. This nameplate must never be

removed.

The appliance must be connected to earth in compliance with electrical

system safety regulations.

If a socket and plug connection is used, check that they are of the same

type. Do not use reducers, adapters or junctions since they may cause

overheating or burns.

If a permanent connection is used, the appliance's power supply line

must be fitted with an omnipolar breaking device with contact gap of at

least 3 mm, located in an easily accessible position close to the

appliance itself.

Operation at 220-240 V

∼

use a type

H05RR-F or H05RN-F three-wire cable

(cable of 3 x 1.5 mm2).

The earth wire (yellow-

reen) must be at

least 20 mm longer than the other wires at

the end for connection to the appliance.

Instructions for the Installer

2.2 Positioning the oven

The appliance is designed for building-in to cabinets made from any heat-

resistant material. Comply with the dimensions shown in figures 1, 2, and 3.

When installing under worktops, comply with the dimensions shown in figure

1-3.

When installing under worktops incorporating combined hobs, a gap of at

least 110 mm must be left from any side wall, as shown in figure 1.

When installing in tall units, comply with the dimensions shown in figure 1-2,

bearing in mind that the top/rear of the unit must have an opening 80-90 mm

deep.

Screw the 4 screws Ainto the inside of the frame (fig. 1).

For installation under tops, make sure that the rear/bottom of the unit has an

opening similar to that shown in figure 1(ref. B). See the instructions supplied

with the hob for the relative positioning and fixing procedures.

Instructions for the Installer

Never use the door for leverage when inserting the

oven in the cabinet.

Never apply excessive pressure to the open door.

Instructions for the User

3. DESCRIPTION OF CONTROLS

3.1 The front panel

All the appliance's control and monitoring devices are placed together on

the front panel.

The table below provides a brief description of the controls shown.

DESCRIPTION OF SYMBOLS

TEMPERATURE SELECTOR KNOB.

SET TEMPERATURE DISPLAY.

CURRENT TIME/PROGRAMMED COOKING OPERATION DISPLAY.

CURRENT TIME/PROGRAMMED COOKING OPERATION

PROGRAMMER KEYS.

SELECTED COOKING OPERATION INDICATOR.

FUNCTION SELECTOR KNOB.

Instructions for the User

FUNCTION SELECTOR KNOB

Turn the knob ( ) either way to select one of

the following functions listed below. The

chosen function will appear on the display

().

TOP AND BOTTOM HEATING

ELEMENTS

TOP + BOTTOM HEATING

EL. + FAN

GRILL ELEMENT

GRILL ELEMENT + FAN

BOTTOM HEATING ELEMENT

CIRCULAR HEATING

ELEMENT

TOP AND BOTTOM HEATING

ELEMENT + CIRCULAR

HEATING ELEMENT

SMALL GRILL ELEMENT +

FAN

DEFROSTING PROVING

BOTTOM HEATING

ELEMENT + FAN

TEMPERATURE SELECTOR KNOB

This knob( ) allows you to set the cooking

temperature between a preset minimum and

maximum for each mode.

After a function has been selected (using

the function selector knob)

the preset value will appear on the temperature display ( ).

To select the cooking temperature turn the knob clockwise (to increase)

or anti-clockwise (to decrease) the value required. The temperature

setting changes in steps of 5°C.

TEMPERATURE INDICATOR

During preheating, the “ ” symbol on the

temperature display ( ) flashes to indicate that the

temperature inside the oven has not yet reached the

set level.

The symbol remains constantly on once the preset

temperature has been reached inside the oven.

Instructions for the User

3.2 Programmer

LIST OF FUNCTIONS

ON/OFF AND CHILD SAFETY BUTTON

TIMER BUTTON

COOKING DURATION BUTTON

END OF COOKING BUTTON

VALUE DECREASE BUTTON

VALUE INCREASE BUTTON

3.2.1 Setting the time

When the oven is used for the first time, or after an interruption in the

electricity supply, the display flashes at regular intervals, showing .

Press the and keys together to stop the display flashing. Press the

value modification keys or to increase or decrease the setting by

one minute for each pressure. Press one of the two value modification

keys until the current time appears.

4 seconds after the last pressure on a key a buzzer will sound to confirm

that the time has been entered.

3.2.2 Changing the time already set

It might become necessary to change the current time, for example at the

switch from summer to winter time. To do this, keep the and keys

pressed for about 4 seconds. A short buzzer will sound to indicate that

the value modification keys or can now be used to change the

current time. 4 seconds after the last pressure on a key a buzzer will

sound to confirm the operation.

Instructions for the User

3.2.3 Switching on the oven

Press the for a short time; the word “On” will appear on the programmer

display. The light inside the oven will come on to indicate that the cooking

operation required can now be set using the function selector knob (see

point 3.1).

3.2.4 Timer

The programmer can also be used as an ordinary timer.

In timer mode, the system will not cut out operation of the oven at the

end of the set time.

Press the key and the display will show the figures ; press the

value modification keys or . The symbol will appear on the display.

4 seconds after the last pressure on a key a buzzer will sound to indicate

that the countdown is starting.

At the end of the programmed time a buzzer will sound and the symbol

will disappear from the display.

To stop the buzzer at the end of the cooking operation press any of the

following keys: , , , , .

After the timer is programmed, the display will return to the current time.

To view the cooking time remaining press the key.

3.2.5 Semiautomatic cooking duration mode

This setting only switches the oven off automatically at the end of the

preset cooking time.

Switch on the oven as described in point 3.2.3.

Press the key and the display will light up showing the figures ;

keep it pressed, and at the same time use the value modification keys

or to set the cooking duration up to a maximum of 10 hours.

4 seconds after the last pressure on a key a buzzer of confirmation will

sound.

The display will show the current time together with the Asymbol.

Select a function using the function selector knob (as described in point

3.1).

Inhaltsverzeichnis

Andere Smeg Ofen Handbücher

Smeg

Smeg DOSFA6390X Bedienungsanleitung

Smeg

Smeg SF465 Bedienungsanleitung

Smeg

Smeg SCA712-2 Bedienungsanleitung

Smeg

Smeg SA578X-9 Bedienungsanleitung

Smeg

Smeg SC709XU Bedienungsanleitung

Smeg

Smeg S320 Bedienungsanleitung

Smeg

Smeg SY6CPX8 Bedienungsanleitung

Smeg

Smeg SA109-8 Bedienungsanleitung

Smeg

Smeg TRA93BL Bedienungsanleitung

Smeg

Smeg Oven Bedienungsanleitung

Smeg

Smeg SF140 Installations- und Betriebsanleitung

Smeg

Smeg SA109-8 Bedienungsanleitung

Smeg

Smeg SU45VCX1 Bedienungsanleitung

Smeg

Smeg SO4602M1NR Bedienungsanleitung

Smeg

Smeg SFP125E Bedienungsanleitung

Smeg

Smeg 3961I Montageanleitung

Smeg

Smeg SOPA6301TX Bedienungsanleitung

Smeg

Smeg SC112-8 Bedienungsanleitung

Smeg

Smeg SOU330X Bedienungsanleitung

Smeg

Smeg SFPA6925B Bedienungsanleitung

Smeg

Smeg SFPA9305SPX Bedienungsanleitung

Smeg

Smeg SA304X-8 Bedienungsanleitung

Smeg

Smeg ALFA31DA Bedienungsanleitung

Smeg

Smeg 91 477 0995 Bedienungsanleitung

Beliebte Ofen Handbücher anderer Marken

Bosch

Bosch HVA531NS0 Bedienungsanleitung

Electrolux

Electrolux EOF6P46X Bedienungsanleitung

NEFF

NEFF B44S32 5GB Series Bedienungsanleitung

Combi

Combi BLODGETT BC142GDS Bedienungsanleitung

AEG

AEG COMPETENCE 311704300 Bedienungsanleitung

Rational

Rational SCC WE 61G Bedienungsanleitung

Electrolux

Electrolux air-o-convect 20 GN 2/1 Bedienungsanleitung

Miele

Miele HR 1954-2 Bedienungsanleitung

KHIND

KHIND OT50 Bedienungsanleitung

Henny Penny

Henny Penny Smoker Box Bedienungsanleitung

Lang

Lang ECOD-AP Bedienungsanleitung

AEG

AEG BEK455310M Bedienungsanleitung

Frigidaire

Frigidaire FNGE90JGR Bedienungsanleitung

Hotpoint

Hotpoint FE9 S831 JSH IX Bedienungsanleitung

GE Advantium SCB2000 Bedienungsanleitung

AEG

AEG DE401301DM Bedienungsanleitung

DeLonghi

DeLonghi XA660 Handbuch

AEG

AEG BEB331010M Bedienungsanleitung