Smeg SC709XU Bedienungsanleitung

Table of Contents

1. IMPORTANT SAFETY INSTRUCTIONS ................................................................................. 4

2. GENERAL INSTALLATION INSTRUCTIONS ......................................................................... 5

3. PREPARING THE BUILT–IN OVEN ....................................................................................... 6

4. MAKING THE ELECTRICAL CONNECTION .......................................................................... 7

NOTE: THIS APPLIANCE MUST BE INSTALLED SOLELY AND EXCLUSIVELY BY A QUALIFIED

TECHNICIAN. ANY TECHNICAL PROCEDURES MUST BE CARRIED OUT BY AN AUTHORIZED

TECHNICIAN.

INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is able to

install, commission and test the appliance

Important Safety Instruction

1. IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS – Your safety and the safety of others are very important.

We have provided many important safety messages throughout this manual and on the appliance.

Read all instructions before using the appliance and always obey all safety messages.

RECOGNIZE SAFETY INFORMATION

This is a safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and

others.

UNDERSTAND SIGNAL WORDS

A signal word – DANGER, WARNING, or CAUTION – is used with the safety-alert symbol. DANGER

identifies the most serious hazards. It means you can be killed or seriously injured if you do not

immediately follow the instructions. WARNING means you can be killed or seriously injured if you do not

follow the instructions. CAUTION indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

All safety messages will inform you of potential hazards, on how to reduce the risk of injury and what

can occur if the instructions are not followed.

IMPORTANT: Installation and grounding must comply with applicable codes. Observe all

government codes and ordinances.

WARNING

- This appliance is intended for home use only.

- Only use the appliance for its intended purpose. The manufacturer is not

responsible for damages caused by improper use of this oven.

- This appliance complies with current safety requirements. Improper use of the

appliance can lead to personal injury and material damage.

- Read all the instructions before installing or using the oven for the first time.

- Keep these operating instructions in a safe place and pass them on to any

future user.

SAVE THESE INSTRUCTIONS

Important Safety Instruction

2. GENERAL INSTALLATION INSTRUCTIONS

•Proper installation is your responsibility. Have a qualified technician install this oven. Make sure

you have everything necessary for correct installation. It is the responsibility of the installer to comply

with installation guidelines specified on the model/serial ID plate. The model/serial ID can be found

on the internal frame of the oven when the door is opened.

•Have your oven installed and properly grounded by a qualified installer, in accordance with

these installation instructions. Grounding is mandatory according to the provisions of the

electrical system safety regulations. If this appliance is connected to an outside electrical power

source, it must be grounded in compliance with local laws, or, if no local laws exist, in compliance

with the national ANSI / NFPA 70 code of electrical regulations.

• Make sure that the voltage and dimensions of the supply line correspond to the information indicated

on the model/serial rating plate. A multi-polar cut-out must be available on the supply line with a

contact opening distance equal to or greater than 3mm, located in an easily accessible position near

the appliance.

• Do not attempt to repair or replace any part of your oven unless it is specifically recommended in this

manual. All other service procedures should be performed by a qualified technician.

• This oven is not suitable for installation and use in mobile homes or campers.

•Electrical grounding is required. See the “Electrical Requirements” section. It is the customer’s

responsibility:

- To contact a qualified electrical installer,

- To ensure that the electrical system is adequate and in compliance with the national ANSI /

NFPA 70 ELECTRICAL CODE – latest edition – Or the CANADIAN ELECTRICAL CODE,

C22.11 – 1982 and C22.2 No. 01982 – or latest edition – and all local codes and ordinances.

IMPORTANT: Observe all government codes and ordinances.

Instructions for the Installer

3. PREPARING THE BUILT–IN OVEN

WARNING

EXCESSIVE WEIGHT HAZARD

- Use two or more people to move and install the oven

- Failure to do so can result in back or other injury.

The oven is designed for installation into any type of cabinetry as long as it is heat-resistant. Proceed

according to the dimensions shown in Pictures 1, 2 and 3. For installing under a countertop, follow the

dimensions given in Picture 3. For installing under a countertop beneath a cooktop with controls

connected to the oven, ensure a minimum clearance from any side walls of at least 110 mm as shown in

Picture 1.

For installing in a column, follow the dimensions given in Picture 2 allowing for a clearance of 80 to 90

mm at the top and sides of the column. Tighten the four screws (ref. A) inside the frame to secure (Pic.

1).

For installing beneath a separate cooktop, allow for a rear and bottom clearance as shown in Picture 1

(ref. B). See instructions regarding fitting and securing the cooktop.

It is important to follow these instructions before and during the oven installation:

• Decide on the final location of the oven. Locate the existing wiring to avoid drilling into or severing

wiring during installation.

• To avoid damage to the floor, place the oven on cardboard prior to installation. Do not lift by the door

handle or any part of the frame or trim.

• Remove the shipping materials and tape from the oven.

• Remove the literature contained in the package.

• Remove and set aside racks and other parts from inside the oven.

• Move the oven on the cardboard close to the oven’s final location.

• Remove the oven door (see paragraph “9.2 Removing the door” in the Instructions for the User

booklet)

IMPORTANT: Use both hands to remove the oven door.

Instructions for the Installer

4. MAKING THE ELECTRICAL CONNECTION

WARNING

ELECTRICAL SHOCK HAZARD

- Disconnect power to the junction box before connecting

- Electrically ground the appliance with green or green-yellow wire

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH,

FIRE OR ELECTRICAL SHOCK.

This appliance is manufactured with a yellow-green or green ground wire connected to the oven chassis.

To prepare the connection between the oven and the junction box:

- Disconnect the power supply to the junction box,

- Feed the flexible cable conduit from the oven through the opening of the cabinet,

- Remove the junction box cover, if present,

- Install a UL-listed or CSA-approved conduit connector to the junction box,

- Route the flexible cable conduit from the oven to the junction box through a UL-listed or CSA-

approved conduit connector.

- Tighten the screws on the conduit connector,

- Refer to figures 1 and 2 below, which represent the most common way of making the electrical

connection.

IMPORTANT: Any local codes and ordinances should be give priority over these instructions.

NOTE: Frame grounded by connection of grounding wire to neutral wire. If used in the new branch circuit

installation (1996 NEC) or if local codes do not permit grounding through the neutral wire, open the

connection and use the grounding wire to the ground unit in compliance with local codes. Connect the

neutral wire to the branch circuit’s neutral conductor in the usual manner:

- Disconnect the ground from the neutral at the free end of the conduit,

- Use the grounding terminal or lead to ground unit, and

- Connect the neutral terminal or wire to the branch circuit neutral in the usual manner (see pic. 2

below)

Instructions for the Installer

US INSTALLATION ONLY – 3 WIRE BRANCH CIRCUIT

Refer to figure 1, where local codes allow the

connection of the ground wire from the applliance

to the branch circuit neutral wire (white wire):

- The ground wire must be connected first;

- If local codes permit, connect the green or

yellow-green ground wire from the appliance

and the white wire from the appliance to the

branch circuit neutral wire (white wire).

- Connect the red and black leads from the oven

to the corresponding leads in the junction box.

fig.1)

US INSTALLATION AND CANADIAN INSTALLATION – 4 WIRE BRANCH CIRCUIT

Refer to figure 2,

- Disconnect the green or yellow-green from the

white lead.

- The ground wire must be connected first;

- Connect the green or yellow-green ground wire

from the appliance to the ground in the junction

box (green colored wire). Do not connect the

grounding wire to the neutral wire in the

junction box.

- Connect the red and black leads from the

appliance to the corresponding leads in the

junction box.

- Connect the white wire from the appliance to the

neutral (white) wire in the junction box.

fig.2)

Connect to a 20A fuse or circuit breaker. Connect to copper wire only, or, if connecting to

aluminum house wire, use UL-listed or CSA-approved connectors, which are suitable for joining

aluminum with copper wires.

Inhaltsverzeichnis

Andere Smeg Ofen Handbücher

Smeg

Smeg SOP6302TX Bedienungsanleitung

Smeg

Smeg FS61XNG8 Bedienungsanleitung

Smeg

Smeg ALFA135BE Bedienungsanleitung

Smeg

Smeg Oven APL360XC Bedienungsanleitung

Smeg

Smeg SIL290X Bedienungsanleitung

Smeg

Smeg Oven SA1010X-5 Bedienungsanleitung

Smeg

Smeg SY92PX Bedienungsanleitung

Smeg

Smeg ALFA135BM Bedienungsanleitung

Smeg

Smeg SOU330X Bedienungsanleitung

Smeg

Smeg AP320 Bedienungsanleitung

Smeg

Smeg HB6422BVN Bedienungsanleitung

Smeg

Smeg SF4301MXK Bedienungsanleitung

Smeg

Smeg SC100 Bedienungsanleitung

Smeg

Smeg SFA4603MCNX Bedienungsanleitung

Smeg

Smeg SE365MF-5 Bedienungsanleitung

Smeg

Smeg SFT476X Bedienungsanleitung

Smeg

Smeg Classica SCB91XI9 Bedienungsanleitung

Smeg

Smeg SA304X-8 Bedienungsanleitung

Smeg

Smeg TRA93P Bedienungsanleitung

Smeg

Smeg SAC106S Bedienungsanleitung

Smeg

Smeg SFA4140VC1 Bedienungsanleitung

Smeg

Smeg DO10PSS Bedienungsanleitung

Smeg

Smeg SFPA309X Installationsanleitung

Smeg

Smeg SF468 Bedienungsanleitung

Beliebte Ofen Handbücher anderer Marken

Bosch

Bosch HVA531NS0 Bedienungsanleitung

Electrolux

Electrolux EOF6P46X Bedienungsanleitung

NEFF

NEFF B44S32 5GB Series Bedienungsanleitung

Combi

Combi BLODGETT BC142GDS Bedienungsanleitung

AEG

AEG COMPETENCE 311704300 Bedienungsanleitung

Falcon

Falcon DOMINATOR PLUS G3106 Series Benutzerhandbuch

Rational

Rational SCC WE 61G Bedienungsanleitung

Electrolux

Electrolux air-o-convect 20 GN 2/1 Bedienungsanleitung

Miele

Miele HR 1954-2 Bedienungsanleitung

KHIND

KHIND OT50 Bedienungsanleitung

Henny Penny

Henny Penny Smoker Box Bedienungsanleitung

Lang

Lang ECOD-AP Bedienungsanleitung

AEG

AEG BEK455310M Bedienungsanleitung

Frigidaire

Frigidaire FNGE90JGR Bedienungsanleitung

Hotpoint

Hotpoint FE9 S831 JSH IX Bedienungsanleitung

GE Advantium SCB2000 Bedienungsanleitung

AEG

AEG DE401301DM Bedienungsanleitung

DeLonghi

DeLonghi XA660 Handbuch