Smeg CS20 Bedienungsanleitung

Contents

1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________34

2. INSTALLATION OF THE APPLIANCE ________________________36

3. ADAPTATION TO DIFFERENT TYPES OF GAS ________________38

4. FINAL OPERATIONS______________________________________40

5. DESCRIPTION OF CONTROLS _____________________________42

6. USE OF THE COOKING HOB _______________________________47

7. USE OF THE OVENS _____________________________________48

8. AVAILABLE ACCESSORIES ________________________________49

9. COOKING HINTS_________________________________________50

10. CLEANING AND MAINTENANCE ____________________________57

11. EXTRAORDINARY MAINTENANCE __________________________60

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE

IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.

INSTRUCTIONS FOR THE INSTALLER: these are for the qualified

technician who must carry out a suitable check of the gas system,

install the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,

description of the commands and the correct procedures for cleaning

and maintenance of the appliance.

Introduction

1. INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND

THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE

PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE

READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE

USING THE COOKER. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED.

INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN

ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS

INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT

REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY

OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD.

ALL OTHER USES ARE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER

USE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE

THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST

SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED

ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE SOCKET

MUST BE THE SAME TYPE AND MUST CONFORM TO CURRENT

REGULATIONS.

THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN

BUILT IN.

NEVER UNPLUG BY PULLING ON THE CABLE.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION

TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW.

SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE

SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION

(OFF) WHEN YOU FINISH USING THE HOB.

NEVER PUT INFLAMMABLE OBJECTS INTO AN OVEN: IF THEY CATCH FIRE

THEY COULD CAUSE A FIRE IN THE HOME.

Introduction

THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND

BRAND NAME IS POSITIONED VISIBLY IN THE STORAGE COMPARTMENT.

THE PLATE MUST NOT BE REMOVED.

DO NOT INSTALL THIS APPLIANCE ON A RAISED PLATFORM.

DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO

TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.

DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS

ON THE COOKING HOB GRIDS.

DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE

OUTER PERIMETER OF THE HOB.

THE APPLIANCE IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW

CHILDREN TO GO NEAR OR PLAY WITH IT.

REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE

COLLECTION CENTRE.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance or by the use of non-original

spares.

Instructions for the installer

2. INSTALLATION OFTHE APPLIANCE

It is the law that all gas appliances are installed by competent persons.

Corgi gas installers are approved to work to safe and satisfactory

standards. All gas installation, servicing and repair work must be in

accordance with the gas safety regulations 1984 (installation and use) as

amended 1990.

This unit is equipped with a type Y fire protection, and may be set

against walls that are higher than the hob.

2.1 Electrical connection

Make sure that the power line voltage matches the specifications

indicated on the rating plate located inside the storage compartment.

This rating plate must never be removed.

The plug at the end of the power cable and the wall socket must be the

same type (conforming to regulations in force). Check that the power line

is adequately grounded. Do not use reducers, adapters or shunts.

On the power line, install an omnipolar cut-off device with contact cut-off

distance greater than or equal to 3 mm, located in an easily accessible

position near the unit.

If the power cable is replaced, the wire

section on the new cable must not be

less than 2.5 mm2(3 x 2.5 cable),

keeping in mind that the end to be

connected to the hob must have the

ground wire (yellow-

reen) longer by

at least 20 mm. Use only the special

cables available at our Service

Centres.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance.

Instructions for the installer

2.2 Ventilation requirements

The room containing the appliance should have an air supply in

accordance with B.S. 5440 part 2 1989.

1. All rooms require an opening window or equivalent, and some

rooms will require a permanent vent as well.

2. For room volumes up to 5 m3an air vent of 100 cm2is required.

3. If the room has a door that opens directly to the outside, and the

room exceeds 1 m3no air vent is required.

4. For room volumes between 5 m3and 10 m3an air vent of 50 cm2is

required.

5. If there are other fuel burning appliances in the same room B.S.

5440 part 2 1989 should be consulted to determine the air vent

requirements.

6. This appliance must not be installed in a bed sitting room of less

than 20 m3or in a bathroom or shower room.

Windows and permanent vents should therefore not be blocked or

removed without first consulting a Corgi gas installer.

Failure to install appliances correctly is dangerous and could lead

to prosecution.

2.3 Connecting to natural and LPG gas

(Please see connection diagram)

Make the connection to the appliance using

flexible bayonet style hose in accordance to B.S.

669. The hose connection at the rear of the

appliance has a 1/2" BSP internal thread. Please

use seal Cbetween the flexible connection Land

the appliance supply tube B. When making the

connection, make sure that no stress of any kind

is applied to the cooker and that the hose does

not touch any sharp edges.

If connecting to LPG the bayonet hose must

have red bands on it.

Instructions for the installer

3. ADAPTATIONTO DIFFERENTTYPES OF GAS

Before performing any cleaning or maintenance work, detach the

appliance from the electrical socket.

The cooking hob of the cooker is inspection-tested for use with G 20

natural gas at a pressure of 20 mbars. If used with other types of gas,

you have to replace the nozzles and regulate the primary air to the

burners. Then regulate the minimum flame on the gas taps. For nozzle

replacement and burner adjustment you must raise the cooking hob as

described in the following paragraph.

3.1 Raising of cooking hob

Remove the grids, first the middle one then the ones at the sides; remove

all the burner caps, the flame cap crowns and the burners.

1. Remove the programmer buttons;

2. Remove the knobs;

3. Unscrew the front panel fixing screws and remove it after

disconnecting the thermostat tell-tale light faston;

4. Loosen the screws of the hinge on the back of the cooker;

5. Raise the surface from the front end;

6. Place the surface support brackets in the front groove of the side;

7. Proceed to replacement of the burner nozzles in accordance with the

appropriate gas table;

8. Adjust the primary air as described in paragraph “3.2 Regulation for

LPG”;

9. After adjustment, fully tighten the fixing screws.

Instructions for the installer

3.2 Regulation for LPG

Loosen screw Aand push air regulator

Bto the bottom.

With a 7 mm wrench, remove nozzle C

and replace it with the proper one

(follow the instructions on the

reference tables for the type of gas to

be used). The torque wrench setting of

the nozzle must not exceed 3 Nm.

Regulate the air by sliding regulator B

until reaching distance “X” shown in

the table in paragraph “3.4 Regulation

of primary air”. Lock regulator B by

tightening screw A.

Burner

Rated

heating

capacity

(kW)

LPG – G30/G31 28/37 mbar

Nozzle

diameter

1/100 mm

By-pass

1/100

Reduced

flowrate

(W)

Flowrate

g/h G30

Flowrate

g/h G31

Auxiliary 1.05 48 30 380 76 75

Semi rapid 1.65 62 30 380 120 118

Rapid 2.55 76 45 800 185 182

Ultra rapid 3.25 85 75 1850 236 232

3.3 Regulation for natural gas

The cooking hob has been inspected for G 20 natural gas at a pressure

of 20 mbar. To allow the unit to work with this type of gas, perform the

same operations described in paragraph “3.2 Regulation for LPG”, but

choose the nozzles and regulate the primary air for natural gas, as shown

in the following table and in paragraph “3.4 Regulation of primary air”.

Burner

Rated

heating

capacity

(kW)

Natural gas – G20 20 mbar

Nozzle diameter

1/100 mm

Reduced flowrate

(W)

Auxiliary 1.05 73 380

Semi rapid 1.65 92 380

Rapid 2.55 115 700

Ultra rapid 3.25 130 1200

Instructions for the installer

3.4 Regulation of primary air

Referred to distance “X” in mm.

BURNER

G20

20 mbar

G30/G31

28/37 mbar

Auxiliary 2.5 2.5

Semi rapid 1 1.5

Rapid 1.5 2.5

Ultra rapid 1.5 2.5

4. FINAL OPERATIONS

Having carried out the above adjustments, reassemble the appliance

following, backwards, the instructions in paragraph “3.1 Raising of

cooking hob”.

After adjustment to a different kind of gas from the one for which the

cooker has been tested, replace the plate inside the storage

compartment with one corresponding to the new kind of gas. This plate

can be obtained from your nearest Authorised Assistance Centre.

4.1 Adjustment of minimum for natural gas

Light the burner and take it to the minimum .

Remove the gas tap knob and turn the

adjustment screw inside or at the side of the tap

shaft (depending on the model) until there is a

regular minimum flame. Replace the knob and

check burner flame stability: (rapidly turning the

knob from maximum to minimum position, the

flame should not go out). Repeat the operation on

all the gas taps.

Instructions for the installer

4.2 Regulation of minimum for LPG

To regulate the minimum for LPG, completely tighten (clockwise) the

screw inside or next to the gas tap pin (depending on the model).

The diameters of the by-passes for each burner are given in table “3.2

Regulation for LPG”.

4.3 Arrangement of burners on cooking hob

BURNERS

1 Auxiliary

2 Semi rapid

3 Rapid

4 Ultra rapid

4.4 Positioning and levelling of the appliance

Having carried out the electricity and gas hook-up, level the appliance

using the four adjustable legs.

Instructions for the user

5. DESCRIPTION OF CONTROLS

5.1 Front control panel

All the cooker controls and commands are on the front panel.

Before using the main oven check that the electronic programmer is

showing the symbol (see paragraph “5.2.1 Clock adjustment”).

DESCRIPTION OF SYMBOLS

BACK LEFT BURNER

BACK RIGHT BURNER

FRONT LEFT BURNER

FRONT RIGHT BURNER

FRONT CENTRAL

BURNER

BACK CENTRAL

BURNER

MAIN OVEN

THERMOSTAT

AUXILIARY OVEN

THERMOSTAT

MAIN OVEN

FUNCTIONS

AUXILIARY OVEN

FUNCTIONS

COOKING HOB BURNER COMMAND KNOB

The flame is lit by pressing the knob and turning it

anticlockwise to maximum flame . To adjust the

flame turn the knob between maximum ( ) and

minimum ( ). The burner goes out when the knob is

returned to the position .

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Smeg Reichweite Handbücher

Smeg

Smeg TRU90X Bedienungsanleitung

Smeg

Smeg CG90IX Bedienungsanleitung

Smeg

Smeg SCB92MX Bedienungsanleitung

Smeg

Smeg SPR30UGGX Bedienungsanleitung

Smeg

Smeg TR90DGC Bedienungsanleitung

Smeg

Smeg SSA60MX8 Bedienungsanleitung

Smeg

Smeg C9GMXA Bedienungsanleitung

Smeg

Smeg SIL68MA8 Bedienungsanleitung

Smeg

Smeg A21X-5 Bedienungsanleitung

Smeg

Smeg CSP20-6 Bedienungsanleitung

Smeg

Smeg A1CXU6 Bedienungsanleitung

Smeg

Smeg C6GVXI Bedienungsanleitung

Smeg

Smeg SPR36UGGX Bedienungsanleitung

Smeg

Smeg SCD60CMX8 Bedienungsanleitung

Smeg

Smeg SSA60GGX8 Bedienungsanleitung

Smeg

Smeg Built-in Microwave Oven Bedienungsanleitung

Smeg

Smeg CS18A-7 Bedienungsanleitung

Smeg

Smeg PRIMASCB9X Bedienungsanleitung

Smeg

Smeg SPR24UGGX Bedienungsanleitung

Smeg

Smeg CS120-6 Bedienungsanleitung

Smeg

Smeg A5-6 Bedienungsanleitung

Smeg

Smeg B72MFX5 Bedienungsanleitung

Smeg

Smeg C6GMNNL8 Bedienungsanleitung

Smeg

Smeg CS19ID-7 Bedienungsanleitung

Beliebte Reichweite Handbücher anderer Marken

Samsung

Samsung FCQ321HTUW Bedienungsanleitung

Kenmore

Kenmore 790.45712 Bedienungsanleitung

Wolf

Wolf CHR CHSSR Bedienungsanleitung

Zanussi

Zanussi ZCG054G Bedienungsanleitung

Whirlpool

Whirlpool 8575985-W Stücklistenhandbuch

Frigidaire

Frigidaire 316000635 Bedienungsanleitung

GE JCSS630 Bedienungsanleitung

Samsung

Samsung NX58M9960P series Bedienungsanleitung

Hotpoint

Hotpoint RB524R Installationsanleitung

Whirlpool

Whirlpool Roper FGP305KW3 Bedienungsanleitung

Amana

Amana ART6610 SERIES Bedienungsanleitung

Maytag

Maytag MERH770WB Bedienungsanleitung

Fulgor Milano

Fulgor Milano SOFIA Bedienungsanleitung

Premier

Premier EF-4358GH Bedienungsanleitung

Kenmore

Kenmore 790.9010 Series Bedienungsanleitung

KitchenAid

KitchenAid KESC300 Bedienungsanleitung

Frigidaire

Frigidaire FFEF3012LS Benutzerhandbuch

Diamond

Diamond G65/2F4T Bedienungsanleitung