SOARNEX EWA-212 Bedienungsanleitung
EWA-212
AC1200 Dual Band PoE Access Point
Quick Installation Guide
快速安裝指南
EWA-212
AC1200 双頻 PoE 供電 AP
Rev1.0 by 2016 Jan
English
Rev1.0 by 2016 Jan2 3 Rev1.0 by 2016 Jan
Contents Of Packing
Initial Access Point Setup
Open the shipping carton and carefully unpack its contents. The
carton should contain the following items.
1. EWA-212 (AC1200 Dual Band PoE Access Point) x 1
2. 1*5Ft (1.5m) network cable x 1
3. Quick Installation Guide x 1
4. Power adapter (12V DC,1A) x 1
5. Mounting Kit x 1
1. Connect the EWA-212 to router or Switch. You may also connect
the device directly to a network port on your computer. If you
are connecting to a router or switch, make sure your computer is
connected to the same network.
2. Plug the power adapter into the EWA-212
3. Wait 60 seconds, then confirm that the status LEDs on the front of
the unit are Illuminated. The EWA-212 access point is now active.
4. Each EWA-212 comes pre-
encrypted with a unique WiFi
Name (SSID) and WiFi password.
You can find your device’s SSID
and WiFi password on the white
labels on the device. Use this
information to connect to the
EWA-212 access point. If the
EWA-212 is reset, the SSID and
WiFi Key will also be reset to the
default login credentials
located on the white lables.
English
Rev1.0 by 2016 Jan4 5 Rev1.0 by 2016 Jan
Hardware Installation
1. Remove the mounting plate from the EWA-212
2. Place the mounting plate on the wall or ceiling where the device
will be located, and mark the location of the screw holes. Ensure
that the device has enough clearance to slide on and off the
mounting plate.
3. Drill out the marketed screw holes, and insert the plastic wall
anchors into the screw holes.
4. Secure the mounting plate, using the screws that came with the
device.
5. Place the EWA-212 on the mounting plate, and attach the network
cable.
Software Controller Management
1. Download Software Controller “SOARNEX AP Utility” from
www.soarnex.com
2. Run the utility. The utility will attempt to detect your device
automatically. If it does not, click on the Discover button.
3. Select your device by checking the box next to your EWA-212, and
click on Device Settings.
English
Rev1.0 by 2016 Jan6 7 Rev1.0 by 2016 Jan
4. The Device Settings page will show your basic Wi-Fi network settings.
If your network requires a static IP address, select the Static radio
button and enter your settings. If you are not sure, leave IP Mode
on the default setting, DHCP
5. To configure your wireless network, select the Band from the
dropdown menu, and enter your settings. If you are using both 2.4
GHz and 5 GHz networks, they must be configured individually. The
Key is your current WiFi password. The default key is located on the
white sticker on the bottom of the EWA-212.
6. When you are finished, enter the password for EWA-212 and click
OK to save your changes. The utility will save your settings.
7. If this is the first time you are accessing the devices, or if the unit
has been reset, the default password is admin. Repeat steps 2 to 6
to configure your other networks.
8. Once your wireless networks are configured, confirm connectivity
by logging into EWA-212 WiFi network. If you can successfully
connect, your configuration is complete.
English
Rev1.0 by 2016 Jan8 9 Rev1.0 by 2016 Jan
9. To access the unit’s advanced settings, launch the Software
Controller Utility, locate your EWA-212, Click on the IP Address, and
select Yes to configure your device.
10. This will launch your default web browser and automatically direct
it to EWA-212 for advanced settings.
11. On the Login screen, enter the username and password. If this
is your first time accessing the device, or if the EWA-212 has been
reset, the default login credentials are. ( Username: admin,
Password : admin)
12. Select the desired Language, and then click Login to continue.
13. The status screen will display information about EWA-212 access
point, and the unit’s wireless networks.
中 文
版本 1.0 2016 年1月
11Rev1.0 by 2016 Jan10
14. For detailed information on advanced settings and features,
please refer to User’s Manual.
This device can be expected to comply with Part 15 of the FCC Rules
provided it is assembled in exact accordance with the instructions
provided with this kit.
Operation is subject to the following conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received including
interference that may cause undesired operation.
© Copyright SOARNEX Technology Corp. 2015
Contents are subject to change without prior notice.
Document is also available on SOARNEX Website.
Certifications
Waste electrical electronic products must not be
disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority for
recycling advice
包裝內容
初始接入点设置
打開包装盒，仔細取出對象。箱內應包含下列項目。
1. EWA-212（AC1200 双頻 POE 供电 AP）×1；
2. 1* 5 英尺（1.5M）网線 ×1。
3. 快速安装指南 x1。
4. 电源适配器（12V DC，1A）×1 ( 選配 )。
5. 安装包 ×1。
1. EWA-212 与路由器或交換机鏈接。您也可以將设备通過网絡端口直
接鏈接到你的計算机上。如果你連接到路由器或交換机，請确保您的
計算机連接到同一网絡。
2. 电源适配器插入 EWA-212
3. 等待 60 秒，然后确認设备前面的 LED 狀態指示灯亮起，該 EWA-212AP
启动完成。
4. 每台 EWA-212 都預设各自的 WiFi
名稱（SSID）和 WiFi 密碼。你可
以在设备的白色標籤上找到該设
备默認的 WiFi 名稱（SSID）和
WiFi 密碼以此來登陸管理设备。
如果 EWA-212 被复位设置，則
设备的 WiFi 名稱（SSID）和 WiFi
密碼將恢复到默認设置。
快速安装指南
中 文
版本 1.0 2016 年1月 版本 1.0 2016 年1月
12 13
硬件安装
1. 拆下 EWA-212 AP 上的安装板
2. 在墙上或者天花板上，定位安装板到 AP 規划的安装位置，標記出螺
絲孔位置。确保足够的行程將 AP 滑动安装拆卸。
3. 鉆出標記的螺絲孔，然后將塑料墙板錨定錨入螺絲孔。
4. 使用該设备附帶的螺絲，固定安装板。
5. 將EWA-212 滑动安装到安装板，并連接网線。
軟件控制
1. 从网站 www.soarnex.com 下載管理軟件 “SOARNEX AP Utility”
2. 运行程序。該程序会嘗試自动檢測您的设备。如果沒有，点擊搜尋
按鈕。
3. 選擇需要设置的设备，并單擊設備設置。
中 文
版本 1.0 2016 年1月 版本 1.0 2016 年1月
14 15
4. 设置设备页面会顯示基本的 WiFi 网絡设置。如果您的网絡需要一个
靜態 IP 地址，選擇靜態配置按鈕，输入设置。如果你不确定，IP 默
認动態配置模式。
5. 要配置您的无線网絡，从下拉菜單中選擇頻段，并输入您的设置。如
果您使用的是 2.4 GHz 和5 GHz 的网絡，必須將它們單獨配置。密碼
是你當前的 WiFi 密碼。默認 WiFi 密碼位于的 EWA-212 底部的白色標
籤上。
6. 當您完成后，输入 EWA-212 登陸密碼，然后單擊确定保存更改。
該实用程序將保存设置。
7. 如果這是您第一次訪問該设备，或者设备已经被重置，默認密碼為
admin。各自重复步驟 2到6來完成配置。
8. 无線网絡配置結束后，可以通過登錄 EWA-212 WiFi 网絡确認連接。
如果可以成功連接，則配置完成。
中 文
版本 1.0 2016 年1月 版本 1.0 2016 年1月
16 17
9. 要訪問设备的高級设置，启动軟件控制工具，找到您的 EWA-212，
点擊 IP 地址，并選擇是來配置设备。
10. 這將启动默認的 Web 瀏覽器，并自动進入 EWA-212 高級设置。
11. 在登錄界面，输入用户名和密碼。如果這是您第一次訪問該设备
，或者如果 EWA-212 已复位，將使用默認的登錄凭据。（用户名：
admin，密碼：admin）
12. 選擇所需的語言，然后單擊登錄繼續。
13. 狀態屏幕將顯示 EWA-212 接入点的信息，和设备的无線网絡。
English
19 Rev1.0 by 2016 Jan
版本 1.0 2016 年1月
18
廢棄电器电子產品不得与生活垃圾混淆。請存放到專门的
回收设施中。請准守地方當局法律法規
14. 有關高級设置和功能的詳細信息，請参閱用户手冊。
該装备符合 FCC 的第十五部分規定，按照說明正确使用該设备。
操作受限以下两个条件
（1）本设备不会產生有害干扰 ,
（2）本设备可以接受任何接收到的干扰 ,但干扰可能致意外操作 .
認證
© Copyright SOARNEX Technology Corp. 2015
内容如有更改恕不另行通知
文件也可在 SOARNEX 网站獲得
Andere SOARNEX Drahtloser Zugangspunkt Handbücher
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
EnGenius
EnGenius EnStationACv2 Bedienungsanleitung
D-Link
D-Link DAP-3662 Bedienungsanleitung
xG Technology
xG Technology xMax CN1300 Bedienungsanleitung
Widelink
Widelink ezWave WAP-1100 Series Bedienungsanleitung
Edimax
Edimax CAP1200 Bedienungsanleitung
