Socket 7Qi Bedienungsanleitung

Choose 2Rent

Phone 1 (800) 622-6484

Fax 1 (866) 937-8254

info@choose2rent.com

www.choose2rent.com

page 1 of 6

1. Powering ON:

Press and hold down the small

power button until the LED turns

blue and the scanner

beeps twice

2. Powering OFF:

Press and hold down

the small power

button until the

scanner beeps

twice.

1. Scanning Barcodes

After connecting the scanner to your

device, open an application. Put the cursor

where you want to enter data. Hold the

scanner about 4 inches from the barcode

and press and hold the trigger button.

Keep your hand steady and make sure the

red beam covers the entire width of the

barcode.

By default, the scanner will beep and

vibrate, and the LED will flash green to confirm that data was decoded

and sent to the host device.

2. Simultaneous Scanning and Soft Keyboard Support

The Scanner supports simultaneous use of the barcode scanner and the

Apple iOS on-screen keyboard while entering data into an application.

To open or close the onscreen keyboard, quickly double-press the

power button (like double-clicking a mouse).

After you double-press the power button, the CHS will beep to indicate

that the onscreen keyboard was enabled / disabled.

Watch a video: http://www.youtube.com/watch?v=VhtttoC6ROs

Use Your Bluetooth Scanner 7Qi

page 2 of 6

3. Pair the Scanner with the Apple device:

-Power on the Scanner

-Make sure the scanner is set to HID Keyboard mode (default). If

needed you can switch to iOS Mode (explained on page 3).

-Enable Bluetooth on the Apple device. Search for Bluetooth devices

-In the list of found devices, select Socket CHS [xxxxxx]. If prompted,

tap Pair.

4. Unpairing the scanner from your iPad or

iPhone

Power on the scanner. Press and hold the

TRIGGER and the POWER button together. After

you hear 3 beeps, release both buttons. The

scanner will unpair and power off.

5. Mounting the Scanner with the QX Stand

When charging the scanner, make sure the

charging pins on the stand and the scanner

make contact with each other and the red LED

on the stand is illuminated. When fastened on

the magnet, the Scanner will enable the sensor

to automatically react to motion and scan any

item.

page 3 of 6

page 4 of 6

•Pair and connect the 7Qi/7Xi to your device prior to placing the scanner

in Auto Mode. The Scanner is not discoverable when in Auto Mode and

in the Stand. This facilitates a fast connection to the current connected

device when powered on (for example the start of the new business

day).

•The Trigger button must be pressed to disable Presentation Mode (and

enable Mobile Mode) after the scanner is removed from the Stand.

•The Scanner will not turn off when it’s in Presentation Mode and in the

Stand under AC Power.

•To avoid excessive power drain, the scanner should not be left out of

the Stand in Auto Mode. Either press the Trigger button or Power off

the scanner.

6. BEEP and Vibration Settings

For full instructions visit:

http://www.socketmobile.com/pdf/data-collection/CHS7Qi-QSG-

Apple.pdf

page 5 of 6

HID MODE Keyboard Pop-up

Enable

The CHS emulates the keyboard in

HID mode. So scanned barcode data

will be input into the text field. The

following steps show how to access

the onscreen keyboard while

connected to the CHS in HID mode.

1. Make sure the CHS is connected

to your Apple device in HID

mode.

2. Open your application and place

the cursor where you want to

enter data.

3. Quickly double-press the power

button of the Scanner (like

double-clicking a mouse) to open

or close the onscreen keyboard.

The CHS will beep once as

confirmation.

IOS MODE - SCANNER-ENABLED

APP

If you are using the CHS with an iOS

device and a Scanner-enabled

Application that does not provide

instructions to connect with the CHS,

please use the following steps.

1. Power on the CHS and scan this

barcode. The CHS will beep 3

times.

2. Turn Bluetooth on for the Apple

device. Go to Settings >

Bluetooth. A Bluetooth Devices

search will begin.

3. Tap Socket Socket 7Xi [xxxxxx]

in the list of Devices found. After

a few seconds the “Not Paired”

status will change to

“Connected” and the CHS Blue

LED will blink every 3 seconds

confirming the connection.

page 6 of 6

Scan Tips

•Be sure to place the QR code 4-6 inches away from the

scanner and slowly back away the QR code till a beep sound

is made.

•Do not wave! Move in and out!

•If scanning a QR code on a mobile

device, be sure to have the device

brightness set to highest. (Especially

devices with privacy screens)

•Be sure to enlarge the QR code to a

reasonable size. You may experience

difficulty if the QR code is too small to

read.

•Cracked screens may cause difficulty

when scanning. Guest should print out

the QR code or ask for assistance from

the Guest Registration Administrator.

Please call our support team if you need assistance

setting up your rental devices

1(800) 622-6484

Andere Handbücher für 7Qi

Andere Socket Barcode-Lesegerät Handbücher

Socket

Socket SOCKETSCAN 800 Series Bedienungsanleitung

Socket

Socket SOCKETSCAN 800 Series Bedienungsanleitung

Socket

Socket DURASCAN D750 Bedienungsanleitung

Socket

Socket CHS 7X Bedienungsanleitung

Socket

Socket CHS 7M Bedienungsanleitung

Socket

Socket 9M Bedienungsanleitung

Socket

Socket D860 Betriebsanleitung

Socket

Socket 2DSC 5 series Bedienungsanleitung

Socket

Socket SOCKETSCAN S800 Bedienungsanleitung

Socket

Socket CHS Series 7 Bedienungsanleitung

Socket

Socket CX2895-1508 Bedienungsanleitung

Socket

Socket 7 Series Bedienungsanleitung

Socket

Socket 8 Series Bedienungsanleitung

Socket

Socket DURASCAN D760 Betriebsanleitung

Socket

Socket 5 Series Bedienungsanleitung

Socket

Socket Socketscan S370 Technisches Datenblatt

Socket

Socket SocketScan 700 Series Bedienungsanleitung

Socket

Socket CHS Series 7 Bedienungsanleitung

Socket

Socket CHS 7Ci Bedienungsanleitung

Socket

Socket CHS Series 7 Bedienungsanleitung

Socket

Socket SocketScan S550 Bedienungsanleitung

Socket

Socket CHS Series 7 Bedienungsanleitung

Socket

Socket XtremeScan Bedienungsanleitung

Socket

Socket Cordless Ring Scanner Series 9 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung