Socket SocketScan S700 Installationshandbuch
COMMAND BARCODES
1D IMAGER MODELS - S700, S800 REV P AND ABOVE
This document pertains to the following S700 and S800 Rev P and above:
The part number (P/N) is labeled inside the battery compartment for the SocketScan®.
Model P/N
S700 Blue 8550-00152
S700 Green 8550-00153
S700 Red 8550-00154
S700 White 8550-00155
S700 Yellow 8550-00156
Model P/N
S800 Black 8550-00069
Rev P and above.
TABLE OF CONTENTS
Factory Defaults —3
Bluetooth Connection Mode —4
Data Sufx —5
Rumble/Beep Modes —6
HID Keyboard Language Settings —7
Advanced Users Only —8
Apple iOS Onscreen Keyboard —8
Bluetooth Connection Mode —10
Bluetooth Connection Roles —10
Automatic Reconnection Settings —11
Data Mode - For SPP Mode Only —11
Power Button Double key Press —12
Scanner Engine Command Barcodes —13
INSTRUCTIONS: Scan command barcode(s) to quickly congure the barcode scanner.
Make sure the scanner is not connected to a host computer or device before scanning a
command barcode!
To use the scanner on multiple hosts, perform the unpair sequence.
1.Power on the scanner.
2.Press and hold down the trigger button.
3.Press and hold down the power button.
4.After you hear 3 beeps, release both buttons.
*NOTE: You may have to “Forget” or “Delete” the pairing on your host device, as well.
By default, the scanner is in Basic Mode (HID) as a Keyboard device.
For scanners in Application Mode (SPP) or Application Mode (MFi-SPP), you can alternatively cong-
ure some settings by using the Scanner Settings app. You can download the app from iTunes, and Google
Play.
3
FACTORY DEFAULTS
Factory Reset
Congures the CHS to revert all settings to factory defaults. The CHS powers off after scanning this bar-
code.
#FNB00F0#
4
BLUETOOTH CONNECTION MODE
Download Companion App or scan one of the conguration command barcode(s). Refer to User Guide for
the full set of command barcodes: socketmobile.com/downloads
Note: Disconnect scanner from host device before scanning a command barcode.
Basic Mode (HID) (default)
(All host devices)
Congures scanner to Basic Mode. Scanner will be discoverable as a keyboard to Bluetooth host devices.
#FNB00F40001#
Application Mode (MFi-SPP) for Apple iOS devices
*Congures scanner to work with an application.
#FNB00F40002#
Application Mode (SPP) for Windows or Android 8.0 and later
(Auto Connect - No conguration required for Application pairing)
*Congures scanner to Serial Port Prole.
#FNB00F40003#
Application Mode (SPP) for Windows or Android 7.0 and lower
(Requires compatible application for Bluetooth pairing)
*Congures the Scanner to Serial Port Prole (SPP).
#FNB00F40000#
*For compatible applications developed with Socket Mobil SDK: socketmobile.com/partners/app
5
All Bluetooth connection modes OK.
You can congure the scanner to automatically add a sufx and/or prex to each scan of data.
Note: Scanning multiple commands in a single instance will overwrite (not append) the previous
command.
Sufx – Carriage Return (default)
Congures the scanner to add a carriage return after decoded data.
#FNB00F50BC6048FFEE1680DE040000#
Sufx – Tab
Congures the scanner to add a tab after decoded data
#FNB00F50BC60408FFEE016809EB040000#
Sufx – Carriage Return & Line Feed
Congures the scanner to add a carriage return and line feed after decoded data.
#FNB00F509C60408FFEE01EB010000#
Data As Is
Congures the scanner to return only the decoded data (i.e., no prex or sufx).
#FNB00F509C60408FFEE01EB00000#
DATA SUFFIX
6
Scan one of the barcodes below and recongure the scanner to remain on longer.
Note: Turn off the host device’s Bluetooth prior to scanning one of the alternate timer barcodes. Then
turn the Bluetooth back on.
Power cycle the scanner (turn off/on).
Scanner Always On*
Congures the scanner to never power off.
Continuous Power for 8 hours*
Scan Barcode to congure the scanner to remain on for 8 hours.
Continuous Power for 4 hours*
Scan Barcode to congure the scanner to remain on for 4 hours.
*These settings drain the battery faster. It is assumed you will charge the scanner within a 24-hour
period or overnight. If you don’t, the scanner’s battery will drain completely.
Return Scanner to Default Setting
Turns the scanner off when it is not in use – 3 to 5 minutes after being disconnected from host device.
ALWAYS ACTIVE MODE
7
All Bluetooth connection modes OK.
IMPORTANT! Make sure the scanner is not connected to a host computer before scanning a command bar-
code.
Vibrate “On”
Enables scanner to vibrate to indicate successful scan
#FNB01310001000100FA0000#
Vibrate “Off”
Disables scanner from vibrating to indicate successful scan
#FNB013100010000#
Beep “On”
Enables scanner to beep to indicate successful scan
#FNB01190E000100030078004B#
Beep “Off”
Disables scanner from beeping to indicate successful scans
#FNB01190E000100000078004B#
RUMBLE/BEEP MODES
8
Scan only with scanner in Basic Mode (HID).
Scan barcode to enable language.
English (Default)
#FNB01430001#
French
#FNB01430002#
German
#FNB01430003#
Spanish
#FNB01430004#
HID KEYBOARD LANGUAGE SETTINGS
9
Scan only with scanner in Basic Mode (HID).
Apple iOS Onscreen Keyboard and Beep Enabled (Default)
Congures the scanner to activate the iOS onscreen keyboard when connected to an iOS device and the
scanner power button is double-pressed.
Disable both Onscreen Keyboard and Beep
#FNB013A0000000000000000000000000000#
Enable Beep
#FNB013A0500000000000000000000000000#
Disable Beep
#FNB013A0100000000000000000000000000#
APPLE iOS ONSCREEN KEYBOARD
DATA MODE - FOR SPP MODE ONLY
All Bluetooth Connection Modes OK.
Advanced users only.
Packet Mode (default)
Congures the scanner to transmit decoded data in packet format.
#FNB013401#
Raw Mode
Congures the scanner to transmit decoded data in raw (unpacketed) format. Do not scan this barcode in
Application Mode (MFi-SPP).
#FNB013400#
10
BLUETOOTH CONNECTION ROLES
Scan only with scanner in Application Mode (SPP) or Application Mode (MFi-SPP)
Advanced users only.
Acceptor (default)
Congures the scanner to accept a Bluetooth connection puts the scanner in discoverable mode.
#FNA#
Initiator
Congures the scanner to initiate a connection to a computer/device with the Bluetooth Device Address
specied in the barcode.
The barcode must be formatted in Code 128 and contain the data #FNIaabbccddeeff# such that aabbccd-
deeff is the Bluetooth Device Address of the computer/device you want to connect to the scanner. Re-
quired for Windows when using SPP mode.
You must create a custom barcode for each computer/device that you want to connect to the scanner.
Use barcode generating software or website (e.g., http://barcode.tec-it.com))
Andere Handbücher für SocketScan S700
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Socket Barcode-Lesegerät Handbücher
Socket
Socket CHS 7Mi Bedienungsanleitung
Socket
Socket In-Hand Scan Card Bedienungsanleitung
Socket
Socket CHS 7M Bedienungsanleitung
Socket
Socket 800 SERIES Bedienungsanleitung
Socket
Socket 7Qi Bedienungsanleitung
Socket
Socket CX2895-1508 Bedienungsanleitung
Socket
Socket CHS 7Ci Bedienungsanleitung
Socket
Socket DuraScan D745 Bedienungsanleitung
Socket
Socket CHS Series 7 Bedienungsanleitung
Socket
Socket CF RFID Bedienungsanleitung
Socket
Socket CHS 7Ci Bedienungsanleitung
Socket
Socket D820 Bedienungsanleitung
Socket
Socket SocketScan S730 Bedienungsanleitung
Socket
Socket Wand Scanner 2E Bedienungsanleitung
Socket
Socket DURASCAN D750 Handbuch
Socket
Socket CX2821-656 Bedienungsanleitung
Socket
Socket SocketScan S550 Bedienungsanleitung
Socket
Socket CHS 7M Bedienungsanleitung
Socket
Socket SocketScan S700 Bedienungsanleitung
Socket
Socket CHS 7Ci Bedienungsanleitung
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
