SOLARACK SR-COMP Bedienungsanleitung
Comp Kit
Installation Manual
© 2018 SOLARACK INC. VR2.1
INSTALL LIKE A PRO
HEX
13
13
One Tool System
mm
HEX
Contents
Check List
SolaRack® Components
Marking
Recomended Spacing
Mounting Instructions: Portrait
Mounting Instructions: Landscape
Grounding & Electrical Diagram
Grounding Path
Qualified PV Frames
UL Requirements & Guidelines
UL STD 1703
UL STD 2703
Universal Mid & End Clamp
Detail Sectional Drawing
Design Code References
Comp Kit - Components
Water Deflector
Required Tools and Torque Values
Installation Manual
Micro Bolt Installation Manual
Warranty
Page 2
Page 3-5
Page 6
Page 7
Page 7
Page 7
Page 8
Page 8
Page 9-11
Page 12
Page 12
Page 12
Page 13
Page 13
Page 14
Page 14
Page 14
Page 16-17
Page 17-21
Page 22-23
Page 24
Page 1 www.solarackusa.com© 2018 SOLARACK INC. VR2.1
BeforeInstallation,Please
ReviewtheFollowingChecklist
● Ensure that SolaRack® is compliant with your module
manufacturer.
● Ensure compliance with any clearances required by
your local fire department of building & safety code.
● Ensure your work complies with naonal, tate and
local requirements - Even those that may supersede
this manual.
● All installaons mu t be preformed by licensed
contractors & electricians that are bonded and
insured.
● Only use system components supplied by SolaRack®
● Make sure your roof is in proper condion prior o
installaon. Do not in tall on damaged roofs!
● Use only appropriate, recommended tools and wear
safety goggles and gloves during installaon
Page 2
FireClassiicationULSTD1703
● Any Roof Slope with Module Types 1 and 2
● Tesng peformed at 5” from roof surface (worst case).
System can be installed at any height.
● Class A rated PV systems can be installed on Class A, B, and C
roofs without afffecng theoof fire ra rang.
Grounding&BondingULSTD2703
Components tested and listed as a grounding method are:
● Universal Mid Clamp
● Universal End Clamp
● Splice Kit
● Micro Bolt, Listed to ground Solaredge Opmiers
5011267
CONFORMS TO
UL STD 2703
www.solarackusa.com© 2018 SOLARACK INC. VR2.1
Page 4
ECORailSystem
ECORAIL
STRDRailSystem HDRailSystem
ECOSPLICE
WIREMANAGEMENT
ECOENDCAP
STRDRAIL
STRDSPLICE
WIREMANAGEMENT
STRDENDCAP
HDRAIL
HDSPLICE
WIREMANAGEMENT
HDENDCAP
Material: Aluminum AL 6000 Series
Finish: Mill Clear & Black Anodized
SKU: SR-ECO
Material: Aluminum AL 6000 Series
SKU: SR-STRD
Material: Aluminum AL 6000 Series
SKU: SR-HD
Material: Aluminum AL 6000 Series
SKU: SR-ECO-SK
Material: Aluminum AL 6000 Series
SKU: SR-STRD-SK
Material: Aluminum AL 6000 Series
SKU: SR-HD-SK
Material: PVC
Finish: Black PVC
SKU: SR-ECO-WM
Material: PVC
Finish: Black PVC
SKU: SR-STRD-WM
Material: PVC
Finish: Black PVC
SKU: SR-HD-WM
Material: PVC
Finish: n/a
SKU: SR-ECO-END
Material: PVC
Finish: n/a
SKU: SR-STRD-END
www.solarackusa.com
Material: PVC
Finish: n/a
SKU: SR-HD-END
Finish: Mill Clear & Black Anodized Finish: Mill Clear & Black Anodized
Finish: Mill Clear & Black Anodized Finish: Mill Clear & Black Anodized Finish: Mill Clear & Black Anodized
© 2018 SOLARACK INC. VR2.1
Page 4
SingleAttachments
COMPKIT
DoubleAttachments Attachments
ADJUSTABLEFLATTILE
ADJUSTABLESTILE
STONECOATEDMETAL
DOUBLECOMPKIT
DOUBLEADJUSTABLEFLAT
DOUBLEADJUSTABLES
DOUBLESTONECOATEDMETAL
L-FOOT
U-ATTACHMENT
STANDOFF
Material: Aluminum AL 1000/6000 Series
Finish: Mill Clear & Black Anodized
SKU: SR-COMP
Material: Aluminum AL 1000/6000 Series
SKU: SR-DCOMP
Material: Aluminum AL 6000 Series
SKU: IGB-SR-LFOOT
Material: SUS304
Finish: Stainless Steel
SKU: SR-ADJF
Material: SUS304
Finish: Stainless Steel
SKU: SR-DADJF
Material: Aluminum AL 6000 Series
Finish: Anodized Clear & Black
SKU: SR-U
Material: SUS304
Finish: Stainless Steel
SKU: SR-ADJS
Material: SUS304
Finish: Stainless Steel
SKU: SR-DADJS
Material: Aluminum AL 6000 Series
Finish: Mill Clear
SKU: SR-SF
Material: SUS304/ AL 6000/1000 Series
Finish: Anodized Clear
SKU: IGB-SR-SCM
Material: US304/ AL 6000/1000 Series
Finish: Anodized Clear
SKU: IGB-SR-DSCM
www.solarackusa.com
Finish: Mill Clear & Black Anodized Finish: Mill Clear & Black Anodized
© 2018 SOLARACK INC. VR2.1
Page 5
GroundingFasteners
U.M.GMIDCLAMP
Material: Aluminum AL 6000 Series
Finish: Mill Clear or Black
Item Number: SR-UMGM
Accessories
U.M.GENDCLAMP
Material: Aluminum AL 6000 Series
MICROBOLT
Material: SUS304
Finish: Stainless Steel
Item Number: SR-MICRO
GROUNDINGLUG
Material: Aluminum AL 6000 Series
Finish: Anodized Clear or Black
Item Number: IGB-SR-2.0MCR
ADJUSTABLEFLATFLASHING
Material: Aluminum AL 1000 Series
Finish: Mill Clear
Item Number: SR-FFLASH2.0
ADJUSTABLESFLASHING
Material: Aluminum AL 1000 Series
Finish: Mill Clear
Item Number: SR-SFLASH2.0
SOLASEAL
Material: Polyether
Finish: n/a
Item Number: SRSFBASE
3/8HEXBOLT&NUT
Material: Aluminum AL 6000 Series
Finish: Anodized Clear or Black
Item Number: IGB-SR-2.0MCR
FRONTTILT
Material: Aluminum AL 6000 Series
Finish: Mill Clear
Item Number: IGB-SR-FT
BACKTILT
Material: Aluminum AL 6000 Series
Finish: Mill Clear
Item Number: IGB-SR-1015/1530/3045
T-BOLT
Material: SUS304
Finish: Stainless Steel
Item Number: SR-TBOLT
www.solarackusa.com
Finish: Mill Clear or Black
Item Number: SR-UMGE
© 2018 SOLARACK INC. VR2.1
Markings on Rails
Page 6
All SolaRack ECO,
STANDARD, & HD Rails are
marked with the following label
UL 2703
Stamped on SolaRack® Mid & End
Clamps Channel nut and Micro Nut.
Item # SR-UMGE / SR-UMGM /
IGB-SR-MICRO
UL 2703
Stamped on ILSCO SGB-4
Grounding Lug
www.solarackusa.com
SOLARACK® PV MOUNTING & BONDING DEVICE
ITEM CODE: SR-HDxxx | Production Date: xx/xx
PROTECTED BY U.S PATENTS
DESIGNED IN CALIFORNIA MANUFACTURED IN CHINA
See Installation Manual for Installation Requirements to
Achieve Specified Fire Class Rating, System Fire Classification
A Type 1 & 2 Low and Steep Slope.
See Installation Manual for Design Loads, Span Charts and
Grounding Instructions.
5011267
CONFORMS TO
UL STD 2703
SOLARACK® PV MOUNTING & BONDING DEVICE
ITEM CODE: SR-HDxxx | Production Date: xx/xx
PROTECTED BY U.S PATENTS
DESIGNED IN CALIFORNIA MANUFACTURED IN CHINA
See Installation Manual for Installation Requirements to
Achieve Specified Fire Class Rating, System Fire Classification
A Type 1 & 2 Low and Steep Slope.
See Installation Manual for Design Loads, Span Charts and
Grounding Instructions.
5011267
CONFORMS TO
UL STD 2703
SOLARACK® PV MOUNTING & BONDING DEVICE
ITEM CODE: SR-Hxxx | Production Date: xx/xx
PROTECTED BY U.S PATENTS
DESIGNED IN CALIFORNIA MANUFACTURED IN CHINA
See Installation Manual for Installation Requirements to
Achieve Specified Fire Class Rating, System Fire Classification
A Type 1 & 2 Low and Steep Slope.
See Installation Manual for Design Loads, Span Charts and
Grounding Instructions.
5011267
CONFORMS TO
UL STD 2703
SOLARACK® PV MOUNTING & BONDING DEVICE
ITEM CODE: SR-HDxxx | Production Date: xx/xx
PROTECTED BY U.S PATENTS
DESIGNED IN CALIFORNIA MANUFACTURED IN CHINA
See Installation Manual for Installation Requirements to
Achieve Specified Fire Class Rating, System Fire Classification
A Type 1 & 2 Low and Steep Slope.
See Installation Manual for Design Loads, Span Charts and
Grounding Instructions.
5011267
CONFORMS TO
UL STD 2703
Grounding Nut’s
Grounding Lug
© 2018 SOLARACK INC. VR2.1
RecommendedPlacement&SpacingofRoofAttachments
Page 7 www.solarackusa.com
1st course
2nd course
3rd course
4th course
48”
72”
IMPORTANT:
Flashing should not overhang a
downslope shingle or a gap in
shingle material. - Roof Rafter
- 9” x 12”
Compositon
MountingInstructions:Portrait MountingInstructions:Landscape
Please follow this instruction graphic when solar modules
are mounted in portrait alignment. Rail must be mounted
8”-18” from the top and bottom edge of the solar module.
Some solar module manufacturers may have specific
requirements rail placement that differs from these
instructions, please check with your module manufacture
for compliance regarding mounting requirements.
Rail must not exceed 24” cantilever
past the last attachment. (for 6’ span)
Please follow this instruction graphic when solar modules
are mounted in landscape alignment. Rail must be mounted
4”-7” from the top and bottom edge of the solar module.
Some solar module manufacturers may have specific
requirements rail placement that differs from these
instructions, please check with your module manufacture
for compliance regarding mounting requirements.
Rail must not exceed 24” cantilever
past the last attachment. (for 6’ span)
The SolaRack® Comp Kit is optimally spaced based on local city code and the rail system used.
For measurements related to clearances and roof setbacks, please refer to your local building and safety office or other
authorities having jurisdiction. When using the Comp Kit with SolaRack® Rails, attachments may be spaced
up to 72”. For proper installation, please refer to the detailed installation guide on page 11. Lag screw must be
installed in the center of a roof rafter and sealant must be applied under the flashing during installation. Installation must be
preformed by licensed professionals to avoid roof damage. Removing stone gravels and deforming shingles in any way
during installation can and will shorten the lifespan of the roofing. Be sure not to install systems on poor quality or damaged
surfaces.
© 2018 SOLARACK INC. VR2.1
Page 8
Fault Current Ground Path
Minimum 10 AWG Copper Wire
SolaRack Rail: ECO, STRD, HD
Under Module Grounding Mid Clamp
Under Module Grounding End Clamp
ILSCO SGB-4 Ground Lug
IGB-SR-MICRO, Micro attachment Bolt
ECO, STRD, HD Grounding Splice Kit
www.solarackusa.com© 2018 SOLARACK INC. VR2.1
QualiiedSolarPVFrames
Page 9
Manufacturer Module Numbers
Systems are allowed to mount module frame/ profile height: 28mm - 46mm
Amerisolar Modules with 35, 40 and 50mm frames and model identifier ASbYxxxZ; where "b" can be 5
or 6; "Y" can be M, P, M27, P27, M30, or P30; and "Z" can be blank, W or WB
Astronergy Modules with 35, 40, and 45mm frames and model identifier aaSM66yyPzz-xxx; where “aa”
can be CH or A; “yy” can be either 10 or 12; and “zz” can be blank, HV,
Auxin Modules with 40mm frames and model identifier AXN6y6zAxxx; where "y" can be M or P; "z"
can be 08,09, 10, 11, or 12; and "A" can be F or T
Axitec Modules with 35 or 40mm frames and model identifier AC-xxxY/aa-ZZ; where “Y” is M or P;
“aa” is 125 or 156; and “ZZ” is 54S, 60S or 72S.
Boviet Modules with 40mm frames and model identifier BVM66aaYY-xxx; where "aa" can be 9, 10
or 12; and "YY" is M or P.
Canadian Solar
Modules with 35 and 40mm frames and model identifier CSbY-xxxZ; where "b" can be 1, 3 or
6; "Y" can be H, K, P, U, V, or X; and "Z" can be M, P, MS, PX , M-SD, P-AG, P-SD, MB-AG,
PB-AG, MS-AG, or MS-SD.
CSUN Modules with 35 and 40mm frames and model identifier YYxxx-zzAbb; where "YY" is CSUN
or SST; "zz” is blank, 60, or 72; "A" is blank, P or M; and "bb" is blank, BB, BW, or ROOF.
Certainteed Modules with 35 and 40mm frames and model identifier CTxxxYZZ-AA; where "Y" can be M
or P; "ZZ” can be 00,01, 10, or 11; and "AA" can be 01, 02 or 03.
EcoSolargy
Modules with 35 & 40mm frames and model identifier ECOxxxYzzA-bbD; where "Y" can be
A, H, S, or T; "zz" can be 125 or 156; "A" can be M or P; "bb" can be 60 or 72; and "D" can
be blank or B.
ET Solar
Modules with 35, 40, or 50mm frames and model identifier ET-Y6ZZxxxAA; where "Y" is P, L,
or M; "ZZ” is 60 or 72; and "AA" is WB, WW, BB, WBG, WWG, WBAC, WBCO, WWCO,
WWBCO or BBAC.
Hanwha Solar Modules with 40, 45, or 50mm frames and model identifier HSLaaP6-YY-1-xxxZ; where "aa"
is either 60 or 72; "YY" is PA or PB; and "Z" is blank or B.
Hanwha Q CELLS
Modules with 32, 35, 40, and 42mm frames and model identifier aaYY-ZZ-xxx; where "aa"
can be Q. or
B.; "YY" can be PLUS, PRO, PEAK, LINE PRO, LINE PLUS, or PEAK DUO; and "ZZ" can
be G3, G3.1,G4, G4.1, L-G2, L-G2.3, L-G3, L-G3.1, L-G3y, L-G4, L-G4.2, L-G4y, LG4.2/TAA,
L-G5.2, L-G5.2/H,LG5.3, BFR-G3, BLK-G3, BFR-G3.1, BLK-G3.1, BFR-G4, BFR-G4.1, BFR
G4.3, BLK-G4.1, G4/SC,G4.1/SC, G4.1/TAA, G4.1/MAX, BFR G4.1/TAA, BFR G4.1/MAX,
BLK G4.1/TAA, BLK G4.1/SC, ECG4.4, G5, BLK-G5, or BLK-G5/SC.
Heliene Modules with 40mm frames and model identifier YYZZxxx; where "YY" is 36, 60, 72, or 96;
and "ZZ" is M, P, or MBLK.
Hyundai Modules with 35, 40mm frames and model identifier HiS-YxxxZZ; where "Y" can be M or S;
and "ZZ" can be KI, MI, MF, MG, SG, RI, RG(BF), RG(BK), TI, or TG
Iteck Modules with 40mm frames and model identifier IT-xxx-YY; where "YY" is blank, HE, or SE,
or Se72.
www.solarackusa.com© 2018 SOLARACK INC. VR2.1
Inhaltsverzeichnis
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
