Solarcentre Everbright Solar Lights Bedienungsanleitung

Stake Mounting

Before attempting to push the stake into the ground, please check that the

ground is not too hard as any damage caused to your solar panel module as a

result of driving them into hard ground is not covered by your warranty. If the

ground is too hard, pour water on the desired area to soften the ground and make

a hole using a strong metal object before driving your stake into the hole. Almost

all of the stake needs to be under ground with only the piece above the ridge being

above ground (see right). Now your stake is in place, locate the extension shaft

and twist it onto the stake mount. The extension shaft is designed to keep the

solar panel module oﬀ the ground to prevent water ingress.

Multimount for wall, fence and deck mounting

Attach the multimount to your wall, fence or decking using the supplied screws

and Rawl plugs. Now your wall mount is in place, locate your solar panel module and

gently push it onto the wall mount until it is fully inserted and secure. Please do

NOT use the extension shaft in conjunction with the multimount as this setup

will not be secure and may cause injury or damage in high winds or other

scenarios. The extension shaft is for use with the stake mount only.

Operating Instructions

The Everbright Solar Lights are fully automatic so once turned on they will come on

automatically at night and turn oﬀ automatically at dawn unless you turn them oﬀ at

the switch. To turn your Solar Lights on simply press the power button on the

underside of the solar panel.

Lighting Modes:

There are 8 modes available on your Everbright Solar Lights and 2 modes on your

Everbright Solar Party, Rattan, Hessian and Chinese Lights. To change modes simply

press the Mode button on the underside of the solar panel.

Choosing your location:

Before setting up your Everbright Solar

Lights you’ll need to think about the

location of the solar panel module. Your

solar panel module needs to be in an

unshaded location where light is not obstructed by buildings, walls, fences, trees, bushes or the shadows that these create. You will

need to rethink your location if your solar panel module can’t reach a bright and unobstructed location. If you are in any doubt

please check before installing your lights. Once you are happy with your solar panel module location, install it by following the guide

below. Once your solar panel module is installed, you can unravel your lights and place them where you like.

EVERBRIGHT

solar lightsTM

User Guide

Thank you for choosing our Everbright Solar Lights, Solar Rattan Lights, Solar Hessian Lights, Solar Party Lights or Solar Chinese

Lights. Please read these instructions carefully before using them.

Box Contents:

Solar panel module, LED Light string, stake mount, extension shaft, multimount, USB charging cable, extension cable, screw and

Rawl plug pack

Setting up your lights

Always take care when setting up your

Everbright Solar Lights especially when

you are situating them in high places. In

the interest of safety, we strongly advise

setting up your solar lights during the

day while it is still light. Children should

only set up the lights with the

assistance and careful supervision of a

responsible adult.

Do:

Don’t:

Do NOT charge

behind glass

Do NOT place your

solar panel shaded

areas.

Ensure your solar

panel is South facing

or as near as possible

Clean your solar

panel from time

to time

Solar Charging Tips

Ridge

1: Stake Mount

3: Multimount

2: Extension shaft

Charging your solar panel module via USB:

Everbright Solar Lights can be charged via USB as well as by the sun. USB enables you to use the lights inside where they can not charge

from the sun. USB charging also enables you to fully charge your lights in the run up to a party or special occasion if the weather has let

you down. Please note that you do not need to take your lights down to charge them via USB. Simply unplug the light string from the solar

panel module and take the solar panel module inside. Before you begin, lift back the rubber cover that protects the USB port (marked D

below) and make sure it is dry. Please note that failure to ensure the solar panel module is dry prior to charging via USB may damage

your solar panel module, USB device or cause injury. Plug the USB end of the cable into your USB device and plug the round adaptor tip

into the solar panel module (under the cover marked D in the illustration below). Once the solar panel module is connected to a USB

device the red LED light next to the charging port on the solar panel module will light up to let you know that the batteries are charging.

USB Charging Times:

50 LED Lights, Party, Hessian, Rattan and Chinese Lights: 3 hours

100 LED Lights: 5 hours

300 LED Lights: 10 hours

Trouble Shooting

My lights are on but it isn’t dark:

Your Everbright Solar Lights have a sensor in the solar panel that tells them when it is dark enough to turn on. If your lights are coming on

during the day by themselves then this suggests that the panel thinks it is dark when it isn’t. This can happen in unusually dark weather

conditions, but usually it is a sign that the solar panel is positioned in a heavily shaded location. Please rethink your solar panel module

location or remove objects obstructing light from reaching the solar panel.

My lights have worked for the ﬁrst few nights and then stopped working:

Usually the Everbright Solar Lights come partially charged so they will work for a few nights without receiving a fresh charge. If the lights

stop working after a few nights then it is likely that they have not received a fresh charge during the ﬁrst few days. Please check the

location of your solar panel before switching the lights oﬀ by using the switch on the underside of the solar panel pack. Leave your lights

switched oﬀ for a minimum of 3 days to allow the batteries to fully charge them via USB.

I can not get my lights to turn on and they never have:

Usually our Everbright Solar Lights come partially charged, but this isn’t always the case. Please check the location of your solar panel

module before switching the lights oﬀ by using the switch on the underside of the solar panel pack. Leave your lights switched oﬀ for a

minimum of 3 days to allow the batteries to fully charge or charge them via USB.

RoHS 

Made in China to Solar Centre Specification

For customer support please contact:

The Solar Centre Ltd

Unit 5 Dencora Centre

Campﬁeld Road T: 0845 094 1250

St Albans W: www.thesolarcentre.co.uk

AL1 5HN E: inf[email protected].uk

Replacing the AA rechargeable batteries:

After several years use you may need to replace your batteries if you notice

that your lights aren’t performing as well as they used to. You can replace your

batteries by removing the battery compartment bung (part A). To remove the

bung ﬁrmly grip part Bwith one hand and wiggle out the bung (part A) with the

other hand. Please do not grip any other part of the solar panel module

(other than part B) when removing the bung as this may damage the

module and invalidate your warranty.

Please replace your batteries with the AA rechargeable batteries

recommended below. When inserting new batteries it is important to ensure

that the new batteries are put in the correct way and that the bung is put back

in the correct way round. To be sure look into the battery compartment and

locate the side that has the spring and place a battery in that side so that the

ﬂat end of the battery goes in ﬁrst against the spring. Place the other battery in

the opposite way up. Ensure the bung is inserted the correct way by making

sure the spring on the bung goes on top of the battery that has its ﬂat end

showing. Please note that AA rechargeable batteries are available from most

shops including supermarkets, newsagents and petrol stations. Please

recycle your old batteries!

Required AA Batteries

Everbright Solar Lights - 50 LED Bulbs: 2 x AA 600mAh NiMH rechargeable batteries

Everbright Solar Lights - 100 LED Bulbs: 2 x AA 1000mAh NiMH rechargeable batteries

Everbright Solar Lights - 300 LED Bulbs: 2 x AA 2000mAh NiMH rechargeable batteries

Everbright Solar Party/Hessian/Rattan/Chinese Lights: 2 x AA 600mAh NiMH rechargeable batteries

solarcentreR

making solar that works

AA Rechargeable batteries

Please DO NOT grip this part

when removing the bung.

Battery compartment

bung

USB charging port

with rubber cover

Grip this part with one hand while removing

the bung with your other hand

CHARGE

Everbright Solar Panel Module

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere solarcentre Laterne Handbücher

solarcentre

solarcentre Curve Bedienungsanleitung

Beliebte Laterne Handbücher anderer Marken

KYOWA

KYOWA KW-9114 Bedienungsanleitung

Stahl

Stahl ECOLUX 6610 Series Bedienungsanleitung

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Bedienungsanleitung

PRG

PRG VARI LITE VL5 Bedienungsanleitung

Raytec

Raytec VARIO2 series Bedienungsanleitung

ENSA

ENSA LEDBT18WS2 Bedienungsanleitung

LUG

LUG OFFICE LB LED N/T Bedienungsanleitung

GE Wallighter 250 Bedienungsanleitung

Draper

Draper RLEDL19/B Bedienungsanleitung

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Bedienungsanleitung

Panasonic

Panasonic EY3741B57 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LCC8T Bedienungsanleitung

Coolon

Coolon WDN-140 Bedienungsanleitung

Holiday Travel

Holiday Travel 834873 Bedienungsanleitung

BEGA

BEGA 84 036 Bedienungsanleitung

BEGA

BEGA 33 596 Bedienungsanleitung

Dale Tiffany

Dale Tiffany GT701162 Bedienungsanleitung

Wagan

Wagan Brite Nite Pop-Up USB Lantern Bedienungsanleitung

solarcentre Everbright Solar Lights Bedienungsanleitung

Beliebte Laterne Handbücher anderer Marken