2. INSTALLATION(continued)
(c) Mount the solar panel in place with fixings supplied
and adjust direction (Fig. 4)
(d) Adjust the PIR motion sensor direction - it has a 90oangle of
adjustment horizontally and 15overtically. Sensitivity and light
delay time can be adjusted using the 2 dials on the bottom of the
motion sensor (Fig. 5).
PLEASE NOTE
Setting to maximum sensitivity could cause the light to be turned
on in error by blown leaves, a moving curtain or small animals, etc.
Experiment to find the bext setting.
(e) Adjust direction of light head, then insert the end of ther wire from
the solar panel into the socket underneath the light unit (Fig. 6)
9. Insert the wire plug from the solar board into the
bottom of the light.
Make sure the wire plug is completely connected.
8. Adjust the direction of light head.
7. Adjust the motion detector direction.
+45°
-45°
15°
It can be set at the range of 8second (counterclockwise rotation to the end) to
3minute(clockwise rotation to the end) .The timer will recount when the sensor
detect a moving signal before the end of the last time, so we advise that you’d
better set the time to minimum when you make the detection range testing or the
walking testing.
Note: The sensor need to wait 1secend to re-work after the light going off. Only
after the end of the time, the light will lighten again when detecting the signal.
+90°
-90°
-100°
+30°
This range refers to the radii of the circular region that appears on the ground
when the light is installed in the 2.5 m height. A minimum detection range (nearly
4 m in radii) rotating a counterclockwise rotation to the end. A maximum
detection range (nearly 15 m in radii) rotating a clockwise rotation to the end.
Operational Guide
1. Battery Installation
2. Testing Mode:
3. “OFF” Statues
4. “AUTO” Statues
Solar LED light, battery voltage 7.4V, 1800mAH, sensing angle> 150 º, in full lit, continuous working time> 4 hours.
The system will be in “power fail safeguard” model. No motion detecting function. Consumes ＜25UA.
I
Before testing, remove the screws in the back, then remove the back cover; connect the battery (1800mAH) with the
power connectors, the system will be started and the red LED indicate light on; the indication LED light will be off after
the system warming up.
ATTENTION:When use this product, please adjust the sensitivity to an appropriate position you
need, please do not adjust the sensitivity to maximum, to avoid the product does not work normally
caused by wrong motion.Because the sensitivity is too high easily detect the wrong motion by wind
blowing leaves & curtains, small animals, and the wrong motion by interference of power grid &
electrical equipment. All those lead the product does not work normally !
When the product does not work normally, please try to lower the sensitivity appropriately, and then
test it.
The system will accept the manual adjustment for “Delay Time” and “Sensi Tivity”.
“Delay time” can be adjusted from 10 seconds to 3 minutes.
“Sensi Tivity” can be adjusted to 15m(22°C).
The brightness of the LED lights: outside ＜10 LUX.
9. Insert the wire plug from the solar board into the
bottom of the light.
Make sure the wire plug is completely connected.
8. Adjust the direction of light head.
7. Adjust the motion detector direction.
+45°
-45°
15°
It can be set at the range of 8second (counterclockwise rotation to the end) to
3minute(clockwise rotation to the end) .The timer will recount when the sensor
detect a moving signal before the end of the last time, so we advise that you’d
better set the time to minimum when you make the detection range testing or the
walking testing.
Note: The sensor need to wait 1secend to re-work after the light going off. Only
after the end of the time, the light will lighten again when detecting the signal.
+90°
-90°
-100°
+30°
This range refers to the radii of the circular region that appears on the ground
when the light is installed in the 2.5 m height. A minimum detection range (nearly
4 m in radii) rotating a counterclockwise rotation to the end. A maximum
detection range (nearly 15 m in radii) rotating a clockwise rotation to the end.
Operational Guide
1. Battery Installation
2. Testing Mode:
3. “OFF” Statues
4. “AUTO” Statues
Solar LED light, battery voltage 7.4V, 1800mAH, sensing angle> 150 º, in full lit, continuous working time> 4 hours.
The system will be in “power fail safeguard” model. No motion detecting function. Consumes ＜25UA.
I
Before testing, remove the screws in the back, then remove the back cover; connect the battery (1800mAH) with the
power connectors, the system will be started and the red LED indicate light on; the indication LED light will be off after
the system warming up.
ATTENTION:
When use this product, please adjust the sensitivity to an appropriate position you
need, please do not adjust the sensitivity to maximum, to avoid the product does not work normally
caused by wrong motion.Because the sensitivity is too high easily detect the wrong motion by wind
blowing leaves & curtains, small animals, and the wrong motion by interference of power grid &
electrical equipment. All those lead the product does not work normally !
When the product does not work normally, please try to lower the sensitivity appropriately, and then
test it.
The system will accept the manual adjustment for “Delay Time” and “Sensi Tivity”.
“Delay time” can be adjusted from 10 seconds to 3 minutes.
“Sensi Tivity” can be adjusted to 15m(22°C).
The brightness of the LED lights: outside ＜10 LUX.
44.50
26.50
6. Place solar board at a sunny location.5. Mount solar board with screws. Adjust the direction.
44.50
26.50
6. Place solar board at a sunny location.5. Mount solar board with screws. Adjust the direction.
44.50
26.50
6. Place solar board at a sunny location.5. Mount solar board with screws. Adjust the direction.
BEFORE FIRST USE - IMPORTANT
(a) THE BATTERY WAS DISCONNECTED before leaving the factory.
You therefore need to remove the battery cover on the back of the
light unit and reconnect the male/female wiring sockets as shown
in Fig. 7 below. (If the light is not going to be used for an extended
period of time, please disconnect the battery.)
(b) Before first use, leave the light in the OFF mode for 24hrs to allow
the solar panel to fully charge the battery.
OPERATIONAL GUIDELINES
(a) If the switch is in the ON position, the light will be on permanently
(whilst battery power allows). If no motion is detected after 8
minutes, the level of brightness will be reduced by about a third.
If battery power is too low for the light to operate properly the unit
will turn off and the LED bulb on the front of the unit will blink. (This
also applies when the switch is in the AUTO position.)
(b) If the switch is in the OFF position, the light will be off permanently,
but the solar panel will continue to charge the battery.
(c) If the switch is in the AUTO position, the unit will activate according
to the settings selected on the SENSITIVITY & TIME DELAY dials.
• The SENSITIVITY dial determines the level of light required to
activate the light.
• The TIME DELAY dial can adjust the time the light stays on after
activating from 10 seconds to 3 minutes.
WALK TEST
Slide switch to AUTO mode. Move the TIME DELAY to to the minimum
and SENSITIVITY dial to maximum. Move across the front
of the PIR sensor. The signal will be detected and the light will come on.
Once the light comes on, remain still. The light should go o after 4 – 6
seconds.
Fig. 4
Fig. 5
Fig. 6
Solar Technology International Limited
Unit 6, Station drive, Bredon, Tewkesbury GL20 7HH
We want your photos and videos!
Here is your chance for you and your solar panel to be a star! Just
send in pics or videos of you and your solar panel in a great location and if selected
we will not only give you ever lasting recognition on our online favourite users
wall of fame but we will send you a Freeloader Sixer, 6000mAH solar power bank
worth £70 completely free!
Please send to hello@solartechnology.co.uk including your address details and
b est of luck!
Note – we cannot guarantee to publish every entry and only those selected by
our marketing department for publication will be awarded a Sixer. By providing
your images you automatically grant us the right to use these images or videos
howsoever we see t.
ISSUE 2020.1
Fig. 7
