Soleus Air HCB-P13HP-D Bedienungsanleitung

Portable Air Conditioner with

Heat Pump Technology

Operating Instructions

3092402

Model No.: HCB-P13HP-D

Reference No.: BPD13HP

V140217

Thank you for choosing a Soleus Air Portable Air Conditioner with Heat Pump Technology. This

owner’s manual will provide you with valuable information necessary for the proper care and

maintenance of your new product. Please take a few moments to thoroughly read the instructions and

familiarize yourself with all the operational aspects of your new Soleus Air Portable Air Conditioner

with Heat Pump technology.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT INSTRUCTIONS

Before installing and using your portable air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference.

1) Always place the unit on a level surface.

2) Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this manual.

3) Maintain at least 10 inches (25 cm) clearance space around this unit. Do not block or cover air inlet or outlet grilles.

4) The unit must be connected to a correctly grounded power supply.

5) Do not start or stop the unit by inserting or pulling out the power plug.

6) Do not use an adapter plug or extension cord.

7) Do not use the unit in the immediate surroundings of a bath, a shower or a swimming pool.

8) Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills unless instructed by this manual.

9) Do not let children play near this unit.

10) Always inspect the cord for signs of damage before use. If the power cord is damaged, it must be replaced by the

manufacturer or a qualified service technician.

11) When cleaning the unit, always turn the unit off and unplug the power cord.

12) When the unit is not in use, always remove the venting kit from window.

13) Do Not Mix Old And New Batteries. Do Not Mix Alkaline, Standard (Carbon - Zinc), Or Rechargeable (Nickel -

Cadmium) Batteries.

14) When changing between heating and cooling mode there will be a 3-5 minute delay for the compressor to start.

During this time, the refrigerant inside the portable air conditioner will return to the compressor to start heating or

cooling your area.

SPECIFICATIONS

• The cooling capacity is measured at an ambient temperature of DB 86 °F, WB 78 °F.

• Noise level is measured at a distance of 3.28 ft away from the front of the unit, when the unit is in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

• If the environment temperature is higher than the max operating temperature or lower than the minimum operating temperature,

the air conditioner may not work properly.

PACKAGE CONTENTS

Portable Air Conditioner (1)

Exhaust Hoses (2)

Hose Adapters (2)

Window Kit Adapter (2)

Air Intake and Outlet Covers (2)

Remote Control (1)

AAA Batteries (2)

Window Kit - 4 Sliding Panels (1 dual hose panel, 1 single hose panel, 2 extension panels)

Air Intake Vent for Single Hose Installation (Additional Accessory) (1)

Owner’s Manual (1)

MODEL HCB-P13HP-D

COOLING CAPACITY 13,000 BTU/H

HEATING CAPACITY 12,500 BTU/H

DEHUMIDIFIER CAPACITY 60 pts/Day

POWER

COOLING 1390W

HEATING 1180W

AIR FLOW VOLUME 225 CFM

POWER SOURCE

115 V~ 60 HZ

11 AMP / 12.5 AMP

HEATING / COOLING

SOUND PRESSURE LEVEL 50 dB(A) at the lowest fan speed

NET WEIGHT 88 Lbs

OPERATING

TEMP

COOLING 60.8℉-107.6℉

HEATING 23℉-89.6℉

PRODUCT DIMENSIONS

REFRIGERANT R-410A

19” W ×18.5” D ×32.25” H

REFERENCE NUMBER BPD13HP

LCDI POWER CORD AND PLUG

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-

ble cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined

value. The cord will remain de-energized until the devise has been manually reset. This is intended to re-

duce the risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded

and they must be considered a shock hazards if exposed. The cord shield must not be connected to ground

or to any exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet. The LED light will turn on.

2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,

3. Press RESET button to restore power to the machine. Once power is restored, the LED light

will turn on again.

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the

air conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Customer Service for troubleshooting

recommendations.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

LED LIGHT

the LED light will turn off.

Note: Your units power cord and plug may differ from the one shown.

PARTS & ASSEMBLY

PARTS

EXHAUST HOSES

WINDOW KIT

ASSEMBLY & INSTALLATION

INSTALLATION

When the unit is operating as an air conditioner, heater, or dehumidifier, the unit draws in fresh outdoor air and exhausts

hot air (in AC or dehumidifier mode) or cool air (in Heat mode) out of the room to complete the air exchange. When the

unit is operating in fan mode, no outdoor air exchange takes place. The window kit and exhaust hose do not need to be

installed when the unit is used as a fan.

NOTE: The supplied window kit can be installed in sliding windows and sliding glass doors up to 8 ft. long

(approximate length).

MOUNTING THE EXHAUST HOSES

• Choose a suitable location, near a grounded electrical outlet and suitable window or door. Remove

packaging and locate components.

• Extend both ends of the exhaust hoses approximately 6 inches.

• Screw the window kit adapter onto one end of the exhaust hose clockwise. Screw the hose adapter onto

the other end of the exhaust hose clockwise. Repeat on the other exhaust hose.

• Remove outlet covers from the back of the unit by screwing them counter-clockwise, then lifting up.

• Mount the exhaust hoses onto the back of the unit by locking the hose adapters into place.

DUAL HOSE WINDOW KIT INSTALLATION - To quickly and efficiently cool a large area.

NOTE: The air conditioner in the images below may differ from the air conditioner you purchased. These

images are for your reference and show how to connect any Soleus Air dual hose air conditioner.

When using to a sliding door, it is recommend to make

the air outlet up to air inlet.

WINDOW KIT ASSEMBLY

1.Parts:

A) 2 Track Screws

B) 2 Wing Nuts

C1 & C2) 2 Hose Panels, one with Two Exhaust Hose Openings

D) 1 Sliding Track Panel

2. Assembly:

First, take the Track Screws (A) and screw one into

each of the small holes found on the Hose Panels

(C1 & C2).

3. Next, take the Wing Nuts (B) and tighten them

around each of the Track Screws (A). Do not tighten

the Wing Nuts (B) all the way; make sure they are

somewhat loose.

4. Now, place the Sliding Track Panel (D) over

the Track Screw (A) on Hose Panel (C1).

5. Next, take the other Hose Panel (C2) and connect it

to Hose Panel (C1) by placing the Sliding Track

Panel (D) over the Track Screw (A) on Hose Panel

(C2).

6. The Hose Panels (C1 &C2) should now be

connected using the Sliding Track Panel (D).

7. To complete the assembly, tighten the wing Nuts

(B) installed earlier. The finished Window Kit should

resemble the image seen below.

SINGLE HOSE EXHAUST & WINDOW KIT INSTALLATION

When you want quick spot cooling, install the PH4-13R-01 using the single hose window kit installation.

For Single Hose Installation

Install only the left exhaust hose over the circular air outlet (this outlet will be on the left side of the unit when

you are facing the back of the unit). Cover the right circular air intake using the exhaust intake cover. After

installing the hose remove the square air intake cover on the back of the unit and install the square air intake

vent with removable/washable filter.

For Single Hose Window Kit Installation

To install the window kit, follow the same directions on page 6 for dual hose installation, but instead of using

the dual hose window kit panel, use the single hose panel pictured below.

Exhaust Hose installed

onto circular air outlet

on left side

Exhaust cover installed

over circular air intake on

right side

Air Intake Cover Air Intake Vent*

Single Hose Window Kit Panel

*Additional Accessory

CONTROL PANEL, DISPLAY, & OPERATING INSTRUCTIONS

CONTROL PANEL & MULTI-COLOR DISPLAY

CONTROL PANEL

MULTI-COLOR DISPLAY

POWER BUTTON

MODE BUTTON

TIMER BUTTONS

TEMP & TIMER SELECTION FAN SPEED BUTTON

TEMP SELECT

AUTO A/C DEHUM. FAN HEAT FAN SPEED

TIMER ON TIMER OFF

TEMPERATURE

AND TIMER

INDICATOR

OSCILLATION ON/OFF

COMPRESSOR ON/OFF

SLEEP MODE

ON/OFF

BUCKET FULL

SWING BUTTON

OPERATING INSTRUCTIONS

CONTROL PANEL BUTTONS (Refer to the images on page 9)

1) Power On and Off - Press the POWER button once to manually turn the unit on. Press the POWER

button once more to turn the unit off.

2) Mode Selection - Press the MODE Button repeatedly to cycle between the different modes: Auto mode,

Air Conditioner, Dehumidifier, Fan only, and Heater.

3) Fan Speed Control - Press the FAN SPEED Button to cycle through the different fan speeds: High,

Medium, and low. The fan speed can be visually distinguished by the speed of the fan icon on the front

panel. There is an additional auto speed setting that is enabled in only heating and cooling modes. This

speed is next setting after low when pressing the speed control button. The speeds will cycle through in this

order: High, Medium, Low, Auto. Each change in speed will be associated with a “beep” sound from the

unit.

4) Temperature - Select the desired temperature by pressing either ▼or ▲key when using the unit in

cooling or heating mode. The temperature indicator flashes to display the desired temperature setting. After

the temperature is set, the unit will display this temperature setting until it is changed by the user. The

Multi-color display shows temperature in Celsius or Fahrenheit. Pressing the ▼and ▲buttons

simultaneously will change the temperature select between °F and °C.

5) Timer - To program the timer, press the TIMER ON button until the display shows a flashing “ ”.

Press the ▲or ▼buttons to change the clock to the desired time for the unit to automatically turn on.

Press the TIMER OFF button and the display on the unit will flash “ ”. Press the ▲or ▼

buttons to change the clock to the desired time for the unit to automatically turn off. The TIMER OFF

indicator will flash for 3 seconds to activate the times you programmed.

NOTE: The timer will also remember your settings when it is set. If you set the timer while in Air

Conditioning mode, the timer will automatically turn the unit on and off in air conditioning mode according to

the desired programmed times. The timer will also remember the temperature settings, fan speed, and

oscillation setting. The timer works when the unit is in Air Conditioner mode, Heating mode, Dehumidifier

mode, Fan mode, and Auto mode

OPERATING THE UNIT USING THE CONTROL PANEL

Air Conditioner Mode

1) Install the exhaust hoses and window kit properly (see pages 6,7 & 8).

2) Plug the Power Cord into an electrical outlet.

3) Turn on the unit by pressing the POWER button on the control panel.

4) Press the Mode button until the “ ” icon appears on the Multi-color display

5) Press the ▲or ▼buttons until the desired room temperature appears on the control panel

display. The temperature ranges from 61°F - 88 °F (16 °C - 31 °C).

6) Select the desired fan speed by pressing the FAN SPEED button.

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air Soleus LX-100 LX-100 Bedienungsanleitung

Soleus Air

Soleus Air PAC12 Bedienungsanleitung

Soleus Air

Soleus Air iCongo PSQ-08-01 Bedienungsanleitung

Soleus Air

Soleus Air PSH-08-01 Bedienungsanleitung

Soleus Air

Soleus Air PE6-10R-03 Bedienungsanleitung

Soleus Air

Soleus Air PS08-01 Bedienungsanleitung

Soleus Air

Soleus Air MAC 7500 Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-08E3 Bedienungsanleitung

Soleus Air

Soleus Air GL-PAC-08E4 Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-15ESE-C Bedienungsanleitung

Soleus Air

Soleus Air PE4-11R-03 Bedienungsanleitung

Soleus Air

Soleus Air PA1-12R-32 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-06ESE-C Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-25ESE-C Bedienungsanleitung

Soleus Air

Soleus Air KY-32U Bedienungsanleitung

Soleus Air

Soleus Air Air condioner Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-18-ID Technisches Datenblatt

Soleus Air

Soleus Air GB-WAC-06SE-C Bedienungsanleitung

Soleus Air

Soleus Air TTWM1-10-01 Bedienungsanleitung

Soleus Air

Soleus Air HCB-P11-A Bedienungsanleitung

Soleus Air

Soleus Air SG-PTAC-09HPDA Bedienungsanleitung

Soleus Air

Soleus Air HP-12 Bedienungsanleitung

Soleus Air

Soleus Air KFHIP-09-OD Technisches Datenblatt

Soleus Air

Soleus Air WS3-06E-201 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung