SOLTEK 82440FX Bedienungsanleitung
1
Notice to End Users
This UserÕs Guide & Technical Reference is for assisting system
manufacturers and end users in setting up and installing the
mainboard.
Every effort has been made to ensure that the information in this
manual is accurate. Soltek Computer Inc. is not responsible for
printing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on the
part of Soltek Computer Inc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek Computer Inc.
Companies and products mentioned in this manual are for
identification purposes only. Product names appearing in this
manual may or may not be registered trademarks or copyrights of
their respective companies.
SOLTEK COMPUTER INC. PROVIDES THIS MANUAL ÒAS ISÓ
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT SHALL SOLTEK COMPUTER
INC. BE LIABLE FOR ANY LOSS OR PROFITS, LOSS OF BUSINESS, LOSS
OF USE OR DATA, INTERRUPTION OF BUSINESS, OR FOR INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY
KIND, EVEN IF SOLTEK COMPUTER INC. HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
© Copyright 1996 Soltek Computer Inc. All right reserved
Edition: August 1996
Version: 1.0
SL-65A SERIAL
2
Contents
Chapter 1: Introduction --------------------------------------- 4
Features -------------------------------------------------------------------------5
Mainboard Layout with Default Settings ------------------------------6
Chapter 2: Hardware Setup---------------------------------- 7
CPU Type Configuration---------------------------------------------------8
CPU 2.5X Clock Setting ----------------------------------------------- 8
CPU 3.0X Clock Setting ----------------------------------------------- 9
System Memory Configuration------------------------------------------- 9
Cooling FAN Settings ----------------------------------------------------- 10
Installation-------------------------------------------------------------- 10
Removal ----------------------------------------------------------------- 11
Jumper Settings ------------------------------------------------------------- 11
Factory Fixed Jumpers----------------------------------------------- 11
JP1, JP2, JP3: Bus Ratio Select ------------------------------------- 12
JP18: Clear CMOS Data--------------------------------------------- 13
JP22: CRT Type Select----------------------------------------------- 13
JP9, JP10: External Bus Frequency Select----------------------- 14
Connectors ------------------------------------------------------------------- 15
KB1: Keyboard Connector ----------------------------------------- 15
MS1: PS/2 Mouse Connector ------------------------------------- 15
PRT1: Parallel Port--------------------------------------------------- 16
COM1 /COM2: Serial Port Connectors ------------------------ 16
Contents 3
FDC: Floppy Drive Connector ------------------------------------ 17
IDE1/IDE2: Primary/Secondary IDE Connectors----------- 17
P3: Power Connector------------------------------------------------ 18
JC1: Speaker Connector -------------------------------------------- 18
JC2: Reset Switch ----------------------------------------------------- 18
JC3: Keylock Switch ------------------------------------------------- 18
JC4: CASE Display Connector ------------------------------------ 18
JC5: SMI Switch ------------------------------------------------------ 19
JP15: Power On Switch --------------------------------------------- 19
HD1: IDE LED Activity Light ------------------------------------- 19
IR1: Infrared Port Module Connector--------------------------- 19
USB: USB Connector ------------------------------------------------ 20
Chapter 3: BIOS Setup ---------------------------------------21
Standard CMOS Setup ---------------------------------------------------- 22
BIOS Features Setup ------------------------------------------------------- 24
Chipset Features Setup --------------------------------------------------- 27
Power Management Setup ----------------------------------------------- 30
PnP/PCI Configuration Setup ------------------------------------------ 32
Load Setup Defaults ------------------------------------------------------- 34
Integrated Peripherals ---------------------------------------------------- 34
Supervisor/User Password---------------------------------------------- 38
IDE HDD Auto Detection ------------------------------------------------ 39
Save & Exit Setup ---------------------------------------------------------- 39
Exit Without Saving ------------------------------------------------------- 39
4
Chapter 1
Introduction
The 82440FX ATX motherboard is a high performance
system hardware based on the Intel Pentium¨
processor and
is equipped with four PCI slots, four standard ISA slots,
Super Multi I/O controller, and dual ports PCI IDE
connectors for future expansion. The hardware dimension
is ATX Form Factor 240mm x 304mm with four layer design
technology.
Introduction 5
Features
¥ Full supports for the Pentium Pro processors and
OverDrive Processors using Socket 8 from 150MHz to
200MHz
¥ CPU bus frequencies up to 66 MHz
¥ATX Form Factor size
¥ Intel 82440FX chipset, PCI Rev 2.1 compliant
¥ Supports wide range of DRAMS from 8MB to 384MB
including:
Ñ FPM, EDO, and BEDO DRAM Types
Ñ 50, 60, and 70ns DRAM speeds
Ñ DRAM supports ECC or Parity function
Ñ Supports 6pcs SIMM DRAM Socket
¥ Supports 4PCI and 4ISA Add-In slots
¥ Integrated Fast IDE Controller
Ñ PIO Mode 4 transfers timing
ÑPCI IDE Bus Master Support
Ñ Supports 2 IDE Connectors for the maximum of 4
IDE Drives (up to 8.4GB for each IDE device)
¥ On-board Super I/O Controller
Ñ One floppy port (include 3.5-inch, 1.2MB, 3 Mode
function)
Ñ Two high speed UART ports (16550 compatible)
Ñ One parallel port with SPP/EPP/ECP capabilities
Ñ Integrated USB (Universal Serial Bus) controller w/i
2 USB ports
Ñ PS/2 mouse connector
¥ Supports Power Management function
¥ Supports Award Plug & Play BIOS with Flash memory
6
Mainboard Layout with Default Settings
The default settings of the following figure is for the
Pentium Pro 180/60.
KeylockSPK Reset T/LED
JC3 JC4JC1 JC2
15
Power
On
IR CON
HDDLED
HD1 IR1 JP15
SMIJC5
PCI1
PCI3
PCI2
COM1
P2
PCI4
MS1KB1
W837877F
82442FX
82371SB
8042
RTC
BIOS
ISA SLOTS
USB1
JP18
Pentium Pro
CPU
Socket 7
–
+
BAT
Don’t touch the heat sinks
avoid burning
COM2 PRT1
IDE2
IDE1
FDC
PCI SLOTS
W48C60-414
JP6
JP3
JP2
JP1
JP5
SIMM1
SIMM2
SIMM2
SIMM4
SIMM5
SIMM6
P3
JP9
JP10
JP22
W82441FX
Figure 1Ð1. Motherboard Layout
Hardware Installation 7
Chapter 2
Hardware Setup
This chapter includes sections of setting up jumpers on the
motherboard, the system memory configuration, the cache
memory configuration, and attaching the connectors. Refer
back to this chapter when you need to upgrade or
reconfigure your system and remember to turn off the
power of the system as well as all peripheral devices before
performing any work on the system.
Symbols used in this chapter are described below:
For 2-pin jumper:
Ð Close the jumper by inserting the jumper
cap over the two pins of the jumper.
Ð Open the jumper by removing the
jumper cap.
For 3-pin jumper:
123
Ð Close pins 1 and 2 with an jumper cap.
123
Ð Close pins 2 and 3 with an jumper cap.
8
CPU Type Configuration
Set the motherboard jumpers JP9, JP10 and JP1~JP3
according to the CPU type as shown in the following
figures.
CPU 2.5X Clock Setting
Pentium Pro
CPU
Socket 7
JP3
JP2
JP1
JP9
JP10
JP9
JP10
Pentium Pro 150/60
JP9
JP10
Pentium Pro 166/66
Figure 2Ð1. CPU Type Configuration
Hardware Installation 9
CPU 3.0X Clock Setting
Pentium Pro
CPU
Socket 7
JP3
JP2
JP1
JP9
JP10
JP9
JP10
Pentium Pro 180/60
JP9
JP10
Pentium Pro 200/66
Figure 2Ð2. CPU Type Configuration
System Memory Configuration
This 82440FX motherboard supports 72-pin SIMMs of 4MB,
8MB, 16MB, or 32MB to form a memory size between 8MB
to 384MB. Each bank must have 2 pcs of DRAM modules
(w/i same size and type) installed. 82440FX chipsets
provide ÒTable-FreeÓ function. It means that users can
install DRAM with any configuration and in any bank, and
that is why the DRAM table is not needed.
10
Cooling FAN Settings
Note: Install a fan facing the heat sink, for better cooling effect,
Installation
1. Place CPU into your socket and put CPU cooler on top of
CPU as shown in the following drawing. Slide one side
hole of clip into the key way of the socket, then
1
2. Press another side hole of clip and slide into socket key
way as shown in the following drawing
2
3. Complete the installation.
3
Inhaltsverzeichnis
Andere SOLTEK Hauptplatine Handbücher
SOLTEK
SOLTEK SL-75KAV Bedienungsanleitung
SOLTEK
SOLTEK SL-65MIV-C Bedienungsanleitung
SOLTEK
SOLTEK 86SP3 Bedienungsanleitung
SOLTEK
SOLTEK SL-85MIR3 Bedienungsanleitung
SOLTEK
SOLTEK SL-75KV Bedienungsanleitung
SOLTEK
SOLTEK 85MR3-R Bedienungsanleitung
SOLTEK
SOLTEK SL-855GEI-FDGR Bedienungsanleitung
SOLTEK
SOLTEK SL-65MV Gebrauchs- und Pflegehandbuch
SOLTEK
SOLTEK 65kv Bedienungsanleitung
SOLTEK
SOLTEK SL-B8E-FG Bedienungsanleitung
SOLTEK
SOLTEK SL-865G Bedienungsanleitung
SOLTEK
SOLTEK SL-65KV2-T Bedienungsanleitung
SOLTEK
SOLTEK SL-845GVI Bedienungsanleitung
SOLTEK
SOLTEK SL-65FVB Bedienungsanleitung
SOLTEK
SOLTEK SL-75DRV2 Bedienungsanleitung
SOLTEK
SOLTEK SL-K8T-939FL Bedienungsanleitung
SOLTEK
SOLTEK SL-65ME Bedienungsanleitung
SOLTEK
SOLTEK SL-85DRV3 Bedienungsanleitung
SOLTEK
SOLTEK SL-845GLI Bedienungsanleitung
SOLTEK
SOLTEK SL-865G3 Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
