SOMFY Sonesse 30 PoE Betriebsanleitung

PROGRAMMING GUIDE

POWER OVER ETHERNET (PoE)

MOTOR WEB INTERFACE

2of 15

VERSION 1.0 |AUGUST 2023 |Prepared by PROJECT SERVICES

SOMFY PoE MOTOR WEB INTERFACE

PROGRAMMING GUIDE

I. INTRODUCTION ----------------------------------------------------3

II. OVERVIEW -------------------------------------------------------- 4

DESCRIPTION

REQUIREMENTS

CONNECTIONS & INDICATORS

III. INSTALLATION ----------------------------------------------------- 5

POWER

BASIC WIRING FOR OPERATION

USING MOTOR LABELS

IV. COMMISSIONING -------------------------------------------------- 7

WEB INTERFACE LOGIN

MOTOR SETTINGS & CONFIGURATION

SET THE ROTATION

SET END LIMITS

NAME THE MOTOR

SET PRESET POSITIONS

ADVANCED SETTINGS

GROUP ADDRESSES

CONTROL THE MOTOR

APPENDIX ------------------------------------------------------------- 14

A. SET FACTORY DEFAULT

B. RESET END LIMITS AND PRESET POSITIONS

C. DIAGNOSTICS INFORMATION

TABLE OF CONTENTS

2of 15

Who is this Guide for?

This guide is aimed at providing support and guidance to installers for setting and programming individual

Power over Ethernet (PoE) motors following installation of motors on projects.

What does this Guide contain?

The sections of this guide contain walkthroughs and methods of programming Power over Ethernet (PoE)

motors using the onboard web interface.

This guide discusses the programming of motors with the onboard web interface.

For questions or assistance please contact technical support:

(800) 22-SOMFY (76639)

technical[email protected]

How should this Guide be used?

This guide is intended to be used as a reference manual.

I. INTRODUCTION

INTRODUCTION

3of 15

SOFTWARE

•Requires access to a web browser from any device that can support a web browser operation

•Root certificate during software installation

HARDWARE

Recommended minimum cabling and connectors:

•CAT-5e SF/UTP (Shielded & Foiled with Unshielded Twisted Pair) cable or higher

Required for installations with high electromagnetic emissions and applications that can produce high

electrostatic charging due to excessive friction(Ex: Dual-roll, zebra shades, and similar shading)

•TIA-568B RJ-45 Connectors - Shielded RJ45 female coupler (#9028957) included with the PoE motors

•Network Router DHCP Server

•Power over Ethernet Network Switch IEEE 802.3at (PoE+) Type2 (30W) or higher

•Sonesse® 30 PoE Motor #1241147

The Power over Ethernet (PoE) Motor is a low-voltage powered distribution and network-connected motor

that utilizes PoE technology power and control from industry-common network switches.

This motor supports both Somfy Synergy™API and CoAP Digital Building API protocols and is

compatible with Power over Ethernet Network Switches IEEE 802.3at (PoE+) Type2 (30W) or higher.

PoE motor system quantity is based on managing the number of devices on the subnet(s) available, unless

specific network configurations are in place and managed by an IT Administrator.

REQUIREMENTS

Ethernet Input

Power & Data from

PoE Switch

CONNECTIONS & INDICATORS

II. OVERVIEW

Programming

Button

Motor Status

LED

PROGRAMMING BUTTON FUNCTIONALITY

TYPE OF PRESS OPERATION FROM PROGRAMMING BUTTON

Short Press (< 2 seconds) Sequential control of the motor UP/STOP/DOWN/STOP

Hold for first Jog Send a DHCP request

Hold for second Jog Force IP assignment method to DHCP

Hold for third Jog Reset to factory mode

4of 15

LED BEHAVIOR:

GREEN

SOLID ON (2 seconds) –POWER UP

BLINKING –BUS COMMUNICATION

AMBER

SOLID ON –MOTOR LIMITS NOT SET

BLINKS TWICE –PUSH IP ADDRESS TO THE

NETWORK

RED

SOLID ON –OBSTACLE DETECTED

BLINKING –THERMAL PROTECTION

BLINKS TWICE –DRIVE IS OUT OF LIMITS

FAST BLINKING –NOT CONNECTED TO THE

NETWORK, NO IP ADDRESS

OFF

LIMITS ARE SET, MOTOR AT IDLE

BASIC WIRING FOR OPERATION

POWER

5of 15

The PoE Motor receives power through the Power over Ethernet Switch.

Cables routed through a metal wall must be protected and insulated by sleeving or sheathing.

III. INSTALLATION

In order to minimize electrostatic charging, end products should avoid:

•Fabric friction with other fabric like in some dual shade applications

•Hardware friction with fabric and other parts of the product such as fascia, cassette, and guide rails

•Excessive ESD caused by fabric friction in dual-roll and Zebra shade installations

•Multiple cycles of product travel without ample rest to dissipate ESD charging

POWER OVER ETHERNET(POE) STANDARDS

IEEE EXTENSION TYPE CLASS

(Power Source Equip.)

POWER PER

DEVICE (W) SOMFY MOTORS

IEEE 802.3at / PoE+ 2 4 30 Sonesse® 30 PoE 1.5Nm

BASIC WIRING FOR OPERATION

USING MOTOR LABELS

Each Somfy PoE motor is supplied with four labels that include motor information to connect to motors.

The label includes a four-digit PIN code for the motor and will be used to log in to the motor.

These codes will be used for the life of the product.

DO NOT DISCARD THE MOTOR INFORMATION LABELS!

One of the motor information labels should remain on the body of the motor. The other three labels should be

shipped in the packaging of the motorized product, or see below for recommended locations to use the labels.

Suggested locations for the Motor Information Labels:

•Finished motorized products:

Examples:

-Attached motor cable

-Removeable shade hem bar

-Motor cover

•Inside the valance of the motorized product

•Work order sheet used in project planning

•Product packaging used for shipping

Example above: On motor tube Example above: Shade hem bar

6of 15

Example above: On motor cable

IMPORTANT NOTE:

Gathering and organizing motor PIN codes and motor information from the included motor

labels is very important in navigating through the PoE motor graphical user interface.

If the PoE WebGUI and the motor become disconnected, the login screen will display to enter

the PIN code to reconnect to the motor.

7of 15

Each PoE motor hosts a web interface for motor setting and configuration. Prior to configuring the motor, obtain the motor information label for

the motor PIN code required for login. Refer to the MAC address to obtain the motor IP address from the network DHCP server.

To configure or adjust PoE motors via the onboard web interface, follow the steps below:

1. OPEN a web browser to NAVIGATE to the

SOMFY PoE WebGUI

2. ENTER the PoE motor IP address or the Host

name in the address bar

NOTE: Motor info entered must start with https://

Example: https://192.168.0.101

3. At the “Your connection isn’t private” prompt,

SELECT “Advanced,” then SELECT “Proceed to

192.168.0.101”

4. At the Login, ENTER the PoE motor PIN code,

then SELECT “Login” to connect to the motor

MOTOR SETTINGS & CONFIGURATION

Starting with “Settings,” continue down the process tree to configure the motor

SELECT “Home” to return to the Home screen or SELECT “Back” to return to a previous screen.

Refer to the Appendix to Factory Reset a motor, to Reset end limits and preset positions, or to view the

Diagnostics information of a motor.

IV. COMMISSIONING

WEB INTERFACE LOGIN

AManufacturer Usage Description (MUD) file is available for each

motor to be used for advanced network security installations.

NOTE: Check with the IT Administrator to find out if a MUD file can be

used in their configuration.

To download the MUD file, SELECT "MUD file“ and navigate to the

downloaded file's location.

8of 15

Settings -Set the Rotation

1. SELECT “Set the rotation”

2. PRESS & HOLD the UP or DOWN button to

move the motor until the button is released

PRESS & RELEASE the UP or DOWN button

to move the motor in small increments

3. SELECT “Reverse” if the motor rotation

direction needs to be reversed

The motor will jog once to confirm the reverse

direction.

A jog is a brief up and down motion of the motor.

4. SELECT “Next” to continue

Settings -Set End Limits

1. SELECT which limit to set first, “Upper limit”

or “Lower limit”

Upper limit is set first in this example.

2. PRESS & HOLD the UP or DOWN button to

move the motor in the direction of the upper

limit

DISABLE “Hold to Move”

With Hold to Move disabled, the motor will

continue moving in the selected direction. Unlike

Press & Hold, this mode requires pressing the

Stop button to stop motor movements.

The motor will not stop automatically when Hold

to Move is disabled.

Take caution when disabling Hold to Move to

prevent damage to the end product.

Enabled Disabled

SELECT the toggle button to enable or disable.

This preference is enabled by default.

3. PRESS the UP or DOWN button to move the motor

in the direction of the upper limit

4. PRESS the STOP button prior to the desired upper

limit

5. ENABLE “Hold to Move,” then PRESS & RELEASE the

UP or DOWN button to move the motor in small

increments until the desired upper limit is reached

6. SELECT “Save at current position” to continue

The motor will jog once to confirm the upper limit is set.

9of 15

7. PRESS & HOLD the UP or DOWN button to

move the motor in the direction of the lower

limit

DISABLE “Hold to Move”

8. PRESS the UP or DOWN button to move the

motor in the direction of the lower limit

9. PRESS the STOP button prior to the desired

lower limit

10. ENABLE “Hold to Move,” then PRESS &

RELEASE the UP or DOWN button to move

the motor in small increments until the desired

lower limit is reached

11. SELECT “Save at current position” to continue

The motor will jog once to confirm the lower limit is set.

Once upper and lower limits are set, the Current range will display. Example: 3600°. This value represents the total

range of movement between the upper and lower limits .

If setting motor limits to a known range, after setting either the upper or lower limit, ENTER a range value, then

SELECT “Save range.”

The motor will jog once to confirm the range is set.

Refer to the Control the Motor section of this guide to test operation of the motor.

Configuration –Name the Motor

1. SELECT “Configuration”

2. SELECT the Motor’s name field

3. ENTER the motor name

Example: Motor 1

4. SELECT the Check Mark icon to save the

name

10 of 15

PoE motors have 16 available preset positions from 0 to 100%. To set preset positions, follow the steps below:

Configuration -Set Preset Positions

1. SELECT “Configuration”

2. SELECT “Set preset positions”

3. SELECT “Modify” to modify a saved position

SELECT “Add a preset position,” to add a

manual position

4. PRESS & HOLD the UP or DOWN button to

move the motor to the desired position

ENTER the position value in %

Example: Position 3 = 75.00%

5. SELECT “Save at current/specified position”

SELECT “Delete” to delete unwanted positions.

SELECT the “Sort by” dropdown to display the

positions by the position index or opening.

To record automatic positions, SELECT “Equally

spaced positions.”

If generating preset positions automatically, this

will delete any positions that were set manually.

SELECT “Yes, generate” to continue.

PRESS the UP or DOWN arrows to select the

quantity of positions. Example: 3

SELECT “Save.”

Refer to the Control the Motor section of this

guide to test operation of the motor.

Andere Handbücher für Sonesse 30 PoE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SOMFY Motor Handbücher

SOMFY

SOMFY ilmo 50 WT Bedienungsanleitung

SOMFY

SOMFY Sonesse 40 RS485 Bedienungsanleitung

SOMFY

SOMFY Sonesse 40 io Bedienungsanleitung

SOMFY

SOMFY Altus Bedienungsanleitung

SOMFY

SOMFY WireFree RTS Betriebsanleitung

SOMFY

SOMFY GOME MOTION Roll Up 28 WT Bedienungsanleitung

SOMFY

SOMFY VRA 10 Bedienungsanleitung

SOMFY

SOMFY LS 40 Bedienungsanleitung

SOMFY

SOMFY Roll Up Basic 28 WFRTS Li-ion Bedienungsanleitung

SOMFY

SOMFY J4 io Bedienungsanleitung

SOMFY

SOMFY LT50 RS485 Bedienungsanleitung

SOMFY

SOMFY Sonesse 30 DCT Bedienungsanleitung

SOMFY

SOMFY Sunea io Bedienungsanleitung

SOMFY

SOMFY Sonesse 30 RS485 Bedienungsanleitung

SOMFY

SOMFY Oximo Series Bedienungsanleitung

SOMFY

SOMFY Sonesse Ultra 50 RTS Bedienungsanleitung

SOMFY

SOMFY CordLift WireFree CT-32RT-12V Bedienungsanleitung

SOMFY

SOMFY Irismo Wirefree Bedienungsanleitung

SOMFY

SOMFY Sonesse 30 RTS 24V DC Betriebsanleitung

SOMFY

SOMFY Sonesse 40 RTS Installationshandbuch

SOMFY

SOMFY Glydea Ultra RTS Series Bedienungsanleitung

SOMFY

SOMFY Tilt & Lift 25 RTS Central Bedienungsanleitung

SOMFY

SOMFY SONESSE 30 ZIGBEE Bedienungsanleitung

SOMFY

SOMFY TLW25 WT Bedienungsanleitung

Beliebte Motor Handbücher anderer Marken

Rotax

Rotax 125 senior MAX evo Bedienungsanleitung

Kohler

Kohler K361 Bedienungsanleitung

MTD

MTD OHV Series Bedienungsanleitung

Kohler

Kohler COMMAND CH18-745 Bedienungsanleitung

Mercury

Mercury D4.2L D-Tronic Bedienungsanleitung

Selve

Selve SE Plus-RC Series Bedienungsanleitung

Perkins

Perkins 1206E-E66TA Bedienungsanleitung

Skov

Skov DA 174 Handbuch

Rossi

Rossi TX11 Series Bedienungsanleitung

Siemens

Siemens SIMOTICS T-1FW3 Merkblatt

AL-KO

AL-KO PRO 350 Bedienungsanleitung

MTU

MTU 12 V 4000 Lx4 Bedienungsanleitung

Nanni

Nanni N3.30 Gebrauchsanweisung

Nanni

Nanni N5.160 CR2 Bedienungsanleitung

KSB

KSB SuPreme Series Montageanleitung

Hiwin

Hiwin EM1 Series Bedienungsanleitung

Rotax

Rotax 912 i series Betriebsanleitung

Siemens

Siemens SIMOTICS XP 1MB1 Bedienungsanleitung