Sonnet TEMPO SERIAL ATA Bedienungsanleitung

TEMPO™SERIAL AT

2-Port Serial ATA Card

Quick Start Guide for Tempo Serial ATA

You Should Have

The following items should be included in your product package:

• One Tempo Serial ATA 2-Port Serial ATA Card

• One Serial ATA data cable

• One legacy to Serial ATA power cable adapter

• Four screws (for mounting hard drives)

The following items may be required for installation:

• Medium Phillips screwdriver

• Drive mounting brackets/carriers or drive mounting sleds (sold

separately)

• One additional Serial ATA data cable (sold separately)

• One or more legacy (4-pin) power cable Y-adapters (sold

separately)

• One additional legacy to Serial ATA (4-pin to 15-pin) power cable

adapter (sold separately)

• One or more Ultra ATA to Serial ATA adapters (only used to support

parallel ATA drives, sold separately)

System Requirements

The Tempo Serial ATA requires the following in order to operate in your

system:

• One available PCI slot

• One or more hard drives (depending on conﬁguration)

• One or more available hard drive bays (depending on conﬁguration)

• Mac OS®8.6 through 9.2.x, Mac OS X Version 10.2.x or later

Remember to register your product online at http://registration.sonnettech.com to be informed of future upgrades and product releases.

Software updates and links are available from the Sonnet web site at www.sonnettech.com. • Online support form available at http://supportform.sonnettech.com.

Sonnet Technologies Customer Service hours are Mon.-Fri., 7 a.m.–5 p.m. Pacific Time • Customer Service Phone: 1-949-472-2772 • E-mail: [email protected]

Sonnet Technologies, Inc., Irvine, California USA • Tel: 1-949-587-3500 Fax: 1-949-457-6350

©2003 Sonnet Technologies, Inc. Revised 2004.All rights reserved. Sonnet, the Sonnet logotype, Simply Fast, the Simply Fast logotype, and Tempo are trademarks of Sonnet Technologies, Inc.Tempo Serial ATA includes technol-

ogy by FirmTek, LLC. Macintosh and Mac are trademarks of Apple Computer, Inc., registered in the United States and other countries. Other product names are trademarks of their respective owners. Product specifications

subject to change without notice. Printed in the USA. QS-TSATA-E-B-112304

Support Notes: We recommend that you make a backup of important

information on your system’s current hard drive prior to installing new

hardware or software.

When handling computer products, you must take care to prevent components

from being damaged by static electricity. Before opening your computer or

removing parts from their packages, always ground yourself first by touching

a metal part of the computer, such as a port access cover, and work in an area

free of static electricity; avoid carpeted areas. Handle all electronic components

only by their edges, and avoid touching connector traces and component pins.

Also, avoid touching the logic board and any of its components.

Installation Preparation

Prior to installing the Tempo Serial ATA and hard drives into your system,

you should familiarize yourself with the parts to be installed. We also strongly

recommend that you read the sections in your computer’s user manual that

address hard drive and PCI card installation.

1. Figure 1 illustrates the Serial ATA data cable included with the Tempo

card; you should plug the straight connector into the Tempo card.

2. Remove the hard drive from its packaging.

3. Locate the connector block on your drive. Many Serial ATA drives are

equipped with both a legacy 4-Pin power connector and a Serial ATA

15-pin power connector (Figure 2). If your drive does not have a 4-pin

power connector, depending on your computer, you may need to use the

included 4-pin to 15-pin power adapter cable.

Hardware Installation Steps

This section covers the installation of the Tempo Serial ATA and one or two

hard drives into your system.

1. Shut down the computer.

2. Open your computer to access its expansion card area (PCI slots) and

drive bay(s); refer to your computer’s user manual for speciﬁc information.

3. Install the hard drives into expansion bays. (Depending on your comput-

er model, drive mounting brackets/carriers or drive mounting sleds may be

required to install your hard drives. Refer to your computer’s user manual.)

4. Plug the supplied Serial ATA data cable’s right angle connector into your

drive; verify the connector is plugged in securely. (If you are connecting

two drives, you will need an additional Serial ATA data cable.)

5. Locate the power connector plugged into your computer’s existing hard

drive. You should ﬁnd at least one extra power connector near the existing

drive; if you have installed only one new drive, plug the extra power con-

nector into it. Connect only one power connector to the drive. If you

have installed more than one new drive, or there are no additional power

connectors, you must use power cable Y-adapters (sold separately). Verify

the connectors are plugged in securely.

Figure 2

Support Note: Technical knowledge may be required to gain access to

the drive expansion bays in certain computers. We recommend you

first consult your computer’s user manual. If you feel you are unable to install

the computer hardware, contact a qualified technician.

Support Note: Serial ATA drives are designed for ease of installation.

Unlike parallel ATA drives, there are no jumpers to set, and each Serial ATA

cable supports only one drive.

Figure 1

Quick Start Guide for Tempo Serial ATA

Serial ATA data cable

Serial ATA power

connector

Serial ATA data

connector legacy power

connector

right angle

connector

straight connector

Quick Start Guide for Tempo Serial ATA

6. Locate an available PCI slot inside your computer and remove its port

access cover, if present, from the rear of the computer.

7. Remove the Tempo Serial ATA card from its packaging.

8. Install the Tempo card into the PCI slot; make sure the card is ﬁrmly

seated.

9. Route the Serial ATA data cable(s) to the Tempo Serial ATA card; avoid

the processor’s heat sink and make sure the cables will not get crushed or

pinched by any part of the case when the computer is reassembled.

10. Plug in the Serial ATA data cable(s) to the Tempo card.

11. Check the cable connections; make sure all cables are connected

securely to the Tempo Serial ATA and the hard drives.

12. Close the computer and carefully replace its cover; be very careful not to

pinch the cables.

Drive Formatting—Mac OS 8.0 through OS 9.x

This section describes the process of formatting (initializing) hard drives con-

nected to the Tempo Serial ATA using Apple Drive Setup under Mac OS 8.6

through Mac OS 9.x. The Drive Setup application is installed during the Mac

OS installation process and is located in the Utilities folder on the hard drive

containing your active System Folder. If you wish to format your drives with

Disk Utility under Mac OS X, please skip to the next section.

1. Turn on your computer.

Figure 3

power supply

access cover

support stand

Support Note: Power Macintosh 7200, 7300, 7500, 7600 and G3

Desktop users must remove the access panel on the main chassis to

route the Serial ATA data cables from the drives to the Tempo card. You may need

tools to perform this procedure. To remove the access panel, first unlock and tilt

up the internal assembly; remember to lower the assembly support stand. Next,

firmly twist the top edge of the panel forward toward the power supply, then lift

the panel out (Figure 3). Save the panel in case you ever need to use it again.

Support Note: If you disconnect your computer’s original internal SCSI

hard disk drive when you install the Tempo Serial ATA and one or more

drives, you must terminate the SCSI chain properly; installation of a SCSI

terminator connector may be required. Failure to properly terminate any SCSI

chain may result in system freezes and errors. Consult your computer’s user guide

or a qualified technician for more information.

WARNING: Hard drives attached to the Tempo Serial ATA will not

mount (appear on the desktop) until they have been formatted; this

includes drives with data on them, previously used in other computers. Please

be aware that formatting a drive erases any data present.

Quick Start Guide for Tempo Serial ATA

Figure 5

2. Open Drive Setup (Figure 4).

3. At this point, you may optionally choose to partition each drive to cre-

ate smaller “virtual” drives to store and retrieve data faster and more efﬁ-

ciently; in the Drive Setup menu bar, select Functions: Volume Settings…

Partition, and set up the partitions. When ready, select the drive listed as

<not initialized>, then click Initialize… to format each of the unmounted

drives (Figure 4).

4. Name each drive or volume once it has been initialized; each volume will

appear on the desktop as a single “virtual” drive (Figure 5). You can now

use your drive(s).

Drive Formatting—Mac OS X Version 10.2 or Later

This section describes the process of formatting (initializing) hard drives con-

nected to the Tempo Serial ATA using Disk Utility under Mac OS X Version

10.2; the process under Version 10.3 is very similar. The drive formatting utility

is located in the Utilities folder (within the Applications folder) on your Mac

OS X volume.

1. Turn on your computer.

2. Open Disk Utility (Figure 6). Note that all attached drives appear in the

Information window, regardless of being formatted or not.

3. Select the drive you want to format by single clicking the drive symbol or

the “name” of the drive (Figure 6). In the Information window, the drive

capacity and Connection type are listed.

Support Note: IDE hard drives attached to the Tempo Serial ATA will

OS X. For example, in Figure 4 the newly installed hard drive appears as <not

initialized> under Volume Name(s) and SCSI under Type.

Figure 4

Figure 6

Support Note: Hard drives attached to the Tempo Serial ATA will regis-

ter as ATA devices to the computer under Mac OS X. For example, in

Figure 6, the Connection Bus for a newly installed hard drive is listed as ATA.

Quick Start Guide for Tempo Serial ATA

Figure 7

4. Click on the Partition tab (Figure 7). When the Partition window

appears, click on the drop down menu beneath “Volume Scheme:” and

select a number of partitions for the volume; you may optionally choose to

partition each drive to create two or more smaller “virtual” drives to store

and retrieve data faster and more efﬁciently.

5. Click to highlight a partition, and then type a name in the Name ﬁeld;

repeat for each partition (Figure 7). After formatting, each will appear in

the Finder window as a drive. If you need to access a drive or partition

from Mac OS 9, be sure to click the Install Mac OS 9 Drivers checkbox.

6. Click Partition (Figure 7).

7. When the Warning window appears, click the Partition button

(Figure 7). If necessary, repeat steps 3–6 to partition the second drive con-

nected to the Tempo Serial ATA. When partitioning and formatting are

complete, close the Disk Utility application; you can now use your drive(s).

Figure 8

Inhaltsverzeichnis

Andere Sonnet Netzwerkkarte Handbücher

Sonnet

Sonnet Aria extreme Bedienungsanleitung

Sonnet

Sonnet PRESTO GIGABIT Bedienungsanleitung

Sonnet

Sonnet PRESTO GIGABIT Ethernet Pro ExpressCard/34 Bedienungsanleitung

Sonnet

Sonnet PRESTO GIGABIT PRO Bedienungsanleitung

Sonnet

Sonnet PRESTO GIGABIT SERVER Bedienungsanleitung

Sonnet

Sonnet Presto 10GbE SFP+ Bedienungsanleitung

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITXR Bedienungsanleitung

Gigafast

Gigafast EE101-AEX Bedienungsanleitung