Sony TA-F501ES Bedienungsanleitung

SERVICE MANUAL

INTEGRATED STEREO AMPLIFIER

AEP Model

UK Model

TA-F501ES

Ver. 1.0 2007.04

SPECIFICATIONS

9-887-686-01

2007D04-1

Sony Corporation

Home Audio Division

Published by SonyTechno Create Corporation

– Continued on next page –

This amplifier incorporates Dolby* Digital and

DTS**.

*Manufactured under license from Dolby

Laboratories.

“Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

** “DTS” and “DTS 2.0” are trademarks of DTS,

Inc.

Amplifier section

POWER OUTPUT

Rated Power Output*6 ohms 1 kHz, THD 0.7%:

65 W + 65 W

Power requirements 230 V AC, 50/60 Hz

*Measured under the following conditions:

Power requirements: 230 V AC, 50/60 Hz

Frequency response

Inputs (Analog)

PHONO RIAA equalization curve

±0.5 dB

TUNER, SA-CD/CD,

TAPE 10 Hz – 40 kHz

±3 dB (8 ohms)

PHONO Sensitivity: 2.5 mV

Impedance: 50 kohms

S/N: 86 dB (A, 20 kHz

LPF)

Output (Analog)

Inputs (Digital)

TUNER, SA-CD/CD,

TAPE Sensitivity: 150 mV

Impedance: 50 kohms

S/N: 96 dB (A, 20 kHz

LPF)

TAPE Voltage: 150 mV

Impedance: 1 kohms

DIGITAL 1/2/3 Impedance: 75 ohms

S/N: 96 dB (A, 20 kHz

LPF)

DIGITAL 4 S/N: 96 dB

(A, 20 kHz LPF)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

TA-F501ES

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN

THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.

REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE

PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR

IN SUPPLEMENTS PUBLISHED BY SONY.

Notes on chip component replacement

•Never reuse a disconnected chip component.

•Notice that the minus side of a tantalum capacitor may be

damaged by heat.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350 °C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

•Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow)

than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

•Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

60 W

Output (Digital)

TONE

General

Power requirements 230 V AC, 50/60 Hz

ower consumption

including projecting parts

and controls

Mass

Supplied accessories

Operating Instructions

Optimizer microphone ECM-AC1 (1)

AC power cord (mains lead) (1)

Remote commander RM-AAU012 (1)

Design and specifications are subject to

change without notice.

DIGITAL 4 S/N: 96 dB

(A, 20 kHz LPF)

TREBLE ±10 dB, 1 dB step

BASS ±10 dB, 1 dB step

Dimensions (w/h/d) (Approx.) 280 ×111 ×

286 mm

(Approx.) 4.6 kg

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

TA-F501ES

TABLE OF CONTENTS

1. SERVICING NOTES ................................................ 4

2. GENERAL ................................................................... 7

3. DISASSEMBLY

3-1. Top Plate, Side Plate ........................................................ 9

3-2. Power Board .................................................................... 10

3-3. Front Panel Assy.............................................................. 10

3-4. Main Board...................................................................... 11

4. TEST MODE.............................................................. 12

5. DIAGRAMS

5-1. Block Diagram – Input Section – .................................... 15

5-2. Block Diagram – DSP Section – ..................................... 16

5-3. Block Diagram – AMP Section – .................................... 17

5-4. Block Diagram – Power Supply Section – ...................... 18

5-5. Printed Wiring Board

– Main Board (Component Side) – ................................. 20

5-6. Printed Wiring Board

– Main Board (Conductor Side) – ................................... 21

5-7. Schematic Diagram – Main Board (1/5) – ...................... 22

5-8. Schematic Diagram – Main Board (2/5) – ...................... 23

5-9. Schematic Diagram – Main Board (3/5) – ...................... 24

5-10. Schematic Diagram – Main Board (4/5) – ...................... 25

5-11. Schematic Diagram – Main Board (5/5) – ...................... 26

5-12. Printed Wiring Board – DSP Board – ............................. 27

5-13. Schematic Diagram – DSP Board – ................................ 28

5-14. Printed Wiring Board – MIC Board – ............................. 29

5-15. Schematic Diagram – MIC Board – ................................ 30

5-16. Printed Wiring Boards – Panel Section – ........................ 31

5-17. Schematic Diagram – Panel Section – ............................ 32

5-18. Schematic Diagram – Power Supply Section – ............... 33

5-19. Printed Wiring Board – Power Supply Section (1/2) – ... 34

5-20. Printed Wiring Boards – Power Supply Section (2/2) –.. 35

6. EXPLODED VIEWS

6-1. Plate Section .................................................................... 50

6-2. Power Board Section ....................................................... 51

6-3. Front Panel Section ......................................................... 52

6-4. Chassis Section................................................................ 53

7. ELECTRICAL PARTS LIST................................ 54

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

TA-F501ES

ERROR MESSAGES

If there is a malfunction, the display shows a code of two numbers. You can check the condition of the system by message. Refer to the

following table to solve the problem. If any problem persists, consult your nearest Sony dealer.

Messages Check code Cause and Response

PROTECTOR 11 Irregular current is output from the speakers. Turn off the ampli-

fier, check the central core of a speaker cord is not touching the

amplifier or other speakers, and turn on again.

PROTECTOR 12 The amplifier section is overheated. Check that the ventilation hole

is not covered. Turn off the amplifier, leave the amplifier for a

while, and turn on the power again.

PROTECTOR 14 Turn off the amplifier, check the central core of a speaker cord is

not touching the amplifier or other speakers.

PROTECTOR 21 Turn off the amplifier and check that the speaker cords are

connected correctly, then turn the power on again.

SECTION 1

SERVICING NOTES

POWER BOARD SERVICE POSITION

POWER board

insulate plate

To check the backside,

remove the AC inlet from the back panel.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

TA-F501ES

MAIN BOARD SERVICE POSITION

No need of connection to

the HP board.

PANEL board

MAIN board

POWER board

AC 2P inlet

SW board

POWER board

AC 2P inlet

SW board

MAIN board

PANEL board

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

TA-F501ES

DISCHARGING THE CAPACITORS

R45

R46

R57

D23

C24

C62

C100

D24

C63

C2 TH1

EP1

D27

FR1

CN11

1234

(CHASSIS)

In order to prevent electric shock when checking the board,

connect between the terminals of the capacitor (C100)

with the specified resistor to discharge the capacitor (C100).

800

Ω

/2W

In order to prevent electric shock when checking the board,

connect between the terminals of the connector (CNP5301)

with the specified resistor to discharge the capacitors (C1532 and C1548).

800

Ω

/2W

CNP5301

MAIN board

C1532

C1548

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

TA-F501ES

SECTION 2

GENERAL This section is extracted from

instruction manual.

Front panel

Location of Parts and Operation

Name Function

APOWER Press to turn the

amplifier on or off.

BRemote sensor Receives signals from

the remote.

CTONE

BASS/TREBLE Turn to adjust the

BASS and TREBLE

levels.

The level can be

adjusted from –10 dB

to +10 dB.

DDisplay The current status of

theselected component

or a list of selectable

items appears here.

Name Function

GMUTING Press to turn off the

sound temporarily.

Press the button again

to restore the sound.

HPHONES jack Connects to

headphones.

EINPUT

SELECTOR Turn to select the input

source to play back.

FVOLUME Turn to adjust the

volume level of

speakers. The level can

beadjustedfrom –∞dB

to +23 dB.

Location of Parts and Operation

Rear panel

AAUDIO INPUT/OUTPUT section

Audio input/

output jacks Connects to a Super

Audio CD player,

tape deck, MD deck

or DAT player, etc

(page 6).

BAUTO CAL MIC jack

Connects to the

supplied optimizer

microphone for the

Auto Calibration

function (page 13).

ESIGNAL GND terminal

If a turntable has a

ground (earth) wire,

connect it to this

terminal to avoid a

hamming noise

(page 6).

CDIGITAL INPUT/OUTPUT section

COAXIAL IN

jacks Connects to a DVD

player, Super Audio

CD player, etc. The

COAXIAL jacks

provide a better

quality sound (page

7).

OPTICAL IN/

OUT jack

DSPEAKERS section

Connectsto speakers

(page 5).

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

TA-F501ES

Remote commander

RM-AAU012

Notes

•Theremotecommand mode of the remotesupplied

with this amplifier is fixed to CD1 for the

connected CD player. Set the remote command

mode of the CD player to CD1; otherwise, you

cannot operate the CD player using this remote.

•Youcan adjust the BASS and TREBLE levels

manually even when the LOUDNESS function is

set to ON. If you adjust the levels manually, the

LOUDNESS function will be switched to OFF,

automatically.

Name Function

ADISPLAY

ON/OFF Press to turn the display in the

display window on and off.

BInput

buttons Press one of the buttons to

select the component you want

to use.

CVOL +/– Press to adjust the volume level

of speakers.

The level can be adjusted from

–∞dB to +23 dB.

DBALANCE

L/R Press to adjust the balance

between left and right speakers.

Both the left and the right

balance can be adjusted from

0dBto+20dB.The initial

setting is 0 dB (center).

EOperation

buttonsfora

Sony CD

player

You can only operate a Sony

CD player using this remote,

when you connect it to the this

amplifier.

Hplayback

Xpause

xstop

./>select a track

m/Mfast backward/

forward

FMUTING Press to turn off the sound

temporarily. Press the button

again to restore the sound.

GMENU Press to display the menu for

the amplifier (page 16).

HV/v/B/bAfter pressing MENU (7),

press V/v/B/bto select the

settings. Then press to

enter the selection (page 16).

ILOUDNESS SettheLOUDNESS functionto

ON to adjust the BASS and

TREBLE levels output from the

speakers to the optimum

settings, based on the volume

level.

When you set the LOUDNESS

function to OFF, the BASS and

TREBLE levels will return to

the levels that had been adjusted

before the LOUDNESS

function was set to ON.

Initial setting is OFF.

JBASS/

TREBLE +/– Press to adjust the BASS and

TREBLE levels. The level can

be adjusted from –10 dB to

+10 dB.

Name Function

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

TA-F501ES

Note: Follow the disassembly procedure in the numerical order given.

3-1. TOP PLATE, SIDE PLATE

•This set can be disassembled in the order shown below.

SECTION 3

DISASSEMBLY

3-1. TOP PLATE,

SIDE PLATE

(Page 9)

SET

3-2. POWER BOARD

(Page 10)

3-3. FRONT PANEL ASSY

(Page 10)

3-4. MAIN BOARD

(Page 11)

two

flat head screws (TP)

two

flat head screws (TP)

two

flat head screws (TP)

two

flat head screws (TP

)

two

flat head screws (TP)

two

flat head screws (TP)

top plate

side plate (L)

side plate (R)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

TA-F501ES

3-2. POWER BOARD

3-3. FRONT PANEL ASSY

three

screws

(+BVTP 3

three

screws

(+BVTP 3

screw (+BVTT 3

two

screws

(+BVTP 3

two

screws

(+BVTP 3

bracket (power MT)

CN11 (4P)

CN1 (2P)

CNP95 (3P)

CNP98 (3P)

CNP97 (6P)

CNP96 (2P)

CNP99 (5P)

POWER boar

two

screws

(+BVTP 3

three

screws

(+BVTP 3

front panel assy

CNP2001 (6P)

CNP2011 (13P)

CNP1401 (15P)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

Andere Handbücher für TA-F501ES

Inhaltsverzeichnis

Andere Sony Verstärker Handbücher

Sony

Sony TA-313 Bedienungsanleitung

Sony

Sony XM-1902GX Bedienungsanleitung

Sony

Sony TA-SB500WR Bedienungsanleitung

Sony

Sony XM-2002GTR - Stereo Amplifier Bedienungsanleitung

Sony

Sony XM-DS1300P5 Operating & Mounting Bedienungsanleitung

Sony

Sony TA-AV571 - Integrated A/v Amplifier Bedienungsanleitung

Sony

Sony TA-F120A Bedienungsanleitung

Sony

Sony TA-N1 Bedienungsanleitung

Sony

Sony XM-430 Primary Bedienungsanleitung

Sony

Sony XM-4060GTX Operating & Connection Bedienungsanleitung

Sony

Sony AV650G Bedienungsanleitung

Sony

Sony XM-GTX6040 - Stereo Power Amplifier Bedienungsanleitung

Sony

Sony XM-6ES Bedienungsanleitung

Sony

Sony XM-405EQX Marketing Specifications Bedienungsanleitung

Sony

Sony XM-255EX Primary Bedienungsanleitung

Sony

Sony TA-F419R Bedienungsanleitung

Sony

Sony TA-SB500WR2 Bedienungsanleitung

Sony

Sony XM-405EQX2 Bedienungsanleitung

Sony

Sony XM-255EX Primary Bedienungsanleitung

Sony

Sony TA-AX410 - Power Amplifier Bedienungsanleitung

Sony

Sony XM-SD14X Bedienungsanleitung

Sony

Sony XM-GTR2022 Bedienungsanleitung

Sony

Sony TA-F530ES Bedienungsanleitung

Sony

Sony XM-D400P5 Product Guide Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung

Phonic

Phonic XP 3000 Bedienungsanleitung