Sony TA-FB720R Bedienungsanleitung
– 1 –
MICROFILM
AEP Model
SPECIFICATIONS
SERVICE MANUAL
INTEGRATED STEREO AMPLIFIER
TA-FB720R/FB820R
Photo :TA-FB820R
– 2 –
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK !OR DOTTED LINE
WITH MARK !ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
TABLE OF CONTENTS
1. GENERAL ..........................................................................3
2. ELECTRICAL ADJUSTMENT ..................................... 4
3. DIAGRAMS
3-1. Circuit Boards Location ........................................................5
3-2. Schematic Diagram – Input Section – .................................. 7
3-3. Printed Wiring Board – Input Section – ................................9
3-4. Schematic Diagram – Main Section – ................................ 11
3-5. Printed Wiring Board – Main Section – ..............................13
3-6. Schematic Diagram – Panel Section – ................................15
3-7. Printed Wiring Board – Panel Section – ............................. 17
3-8. Schematic Diagram – Power Section –............................... 19
3-9. Printed Wiring Board – Power Section – ............................21
3-10. IC Block Diagrams............................................................23
3-11. IC Pin Function ................................................................. 24
4. EXPLODEDVIEW
4-1. Case and Back Panel Section ..............................................25
4-2. Front Panel Section .............................................................26
4-3. Chassis Section ................................................................... 27
5. ELECTRICAL PARTS LIST ........................................28
– 3 –
Front Panel Descriptions
SECTION 1
GENERAL
1PROTECTION indicator
2U(Power) button
3Remote sensor
4TAPE 1/DAT indicator
5TAPE 2/MD indicator
6AUX indicator
7CD indicator
8TUNER indicator
9PHONO indicator
10 INPUT SELECTOR knob
11 VOLUME knob
12 SUBSONIC button
13 SOURCE DIRECT button and indicator
14 LOUDNESS button
15 TAPE MONITOR knob
16 BALANCE knob
17 TREBLE knob
18 BASS knob
19 SPEAKERS knob
20 PHONE jack
21 EON LINK button
This section is extracted from
instruction manual.
10
32
1978465
11
13 12141516171819
20
21
– 4 –
SECTION 2
ELECTRICAL ADJUSTMENT
Bias Adjustment
NOTE:
1. Perform the adjustment after the unit has warmed up sufficiently.
2. Perform the bias adjustment if the power transistor has been
replaced.
Procedure:
1. Rotate fully the bias adjusting semi-fixed resistors (RV500,
RV600) to the MIN position (counterclockwise).
2. Connect a digital voltmeter to the CN500 and CN600.
3. Set the slide regulator to 0V, and press the Ubutton (ON) on
the set.
4. Raise graduallythe slideregulatorvoltage up to the ratedvoltage.
5. At this time,confirm that the SP relay is turned on (it will click).
6. Adjust the RV500 and RV600 so that a reading of digital
voltmeter is 10 ± 0.1 mV.
7. Return the slidack to 0V, and press the Ubutton (OFF) on the
set.
Adjustment Location :
[MAIN BOARD] – COMPONENT SIDE –
1 pin 3 pin
–
–
+
+
CN500 (L-CH)
CN600(R-CH)
+
CN600 (R-CH)
1
3
CN500 (L-CH)
1
3
RV600
Bias (R-CH)
RV500
Bias (L-CH)
DIGITAL
VOLTMETER DIGITAL
VOLTMETER
+
– 5 – – 6 –
SECTION 3
DIAGRAMS
3-1. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTEDWIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this,the necessary note is printed
in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
•¢: internal component.
•2: nonflammable resistor.
•5: fusible resistor.
•C: panel designation.
For printed wiring boards.
Note:
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•b: Pattern from the side which enables seeing.
•U: B+ Line.
•V: B– Line.
•H: adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : POWER ON
• Voltages aretakenwith aVOM(Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F:TUNER
WAVEFORM
1
IC902 1XOUT
Note: The components identified by mark !or dotted line
with mark !are critical for safety.
Replace only with part number specified.
• Indication of transistor
CThese are omitted
EB
4MHz
3.8Vp-p
PANEL board
INPUT board
MAIN board
SP-TM board
PHONO board
PS board OUTLET board
VOL board
SIRCS board
SIRCS SUB board
HP board
SP-SW board
– 7 – – 8 –
TA-FB720R/FB820R
3-2. SCHEMATIC DIAGRAM – INPUT SECTION –
• See page 23 for IC Block Diagrams.
(Page 15)
(Page 15)
(Page 12)
– 9 – – 10 –
TA-FB720R/FB820R
3-3. PRINTED WIRING BOARD – INPUT SECTION –
• See page 5 for Circuit Boards Location.
Ref. No. Location
• Semiconductor
Location
D101 B-7
D102 B-8
D133 C-9
D140 B-4
D240 B-4
IC101 B-9
Q101 C-7
Q102 C-7
Q103 C-8
Q140 C-4
Q240 B-4
(Page 18) (Page 17)
(Page 13)
– 11 – – 12 –
TA-FB720R/FB820R
3-4. SCHEMATIC DIAGRAM – MAIN SECTION –
• See page 23 for IC Block Diagrams.
(Page 16)
(Page 16)
(Page
20)
(Page
15)
(Page 8)
(Page 20)
– 13 – – 14 –
TA-FB720R/FB820R
3-5. PRINTED WIRING BOARD – MAIN SECTION –
• See page 5 for Circuit Boards Location. Ref.No. Location
• Semiconductor
Location
D500 C-10
D501 C-10
D502 C-10
D503 E-11
D504 E-10
D505 E-10
D506 D-9
D511 E-2
D512 E-2
D513 F-3
D600 G-10
D601 G-10
D602 G-10
D603 E-11
D604 E-10
D605 E-10
D606 F-9
D700 A-1
D701 A-1
D702 A-1
D703 G-4
D720 E-7
D721 E-7
IC700 B-2
Q500 C-11
Q501 C-11
Q502 C-10
Q503 D-11
Q504 D-10
Q505 D-10
Q506 E-11
Q507 E-10
Q508 D-9
Q509 D-8
Q510 D-8
Q511 C-5
Q512 C-8
Q513 D-6
Q600 G-11
Q601 G-11
Q602 G-10
Q603 F-11
Q604 F-10
Q605 F-10
Q606 E-11
Q607 E-10
Q608 F-9
Q609 F-8
Q610 F-10
Q611 G-8
Q612 G-5
Q613 F-6
Q700 B-3
Q701 B-1
Q702 G-4
(Page 22)
(Page 10)
(Page 22)
(Page 18)
(Page 18)
(Page 17)
– 15 – – 16 –
TA-FB720R/FB820R
3-6. SCHEMATIC DIAGRAM – PANEL SECTION –
• See page 5 forWaveforms.
• See page 23 for IC Block Diagram.
• See page 24 for IC Pin Function.
(Page 8)
(Page 12)
(Page 7)
(Page
11)
(Page 11)
Andere Handbücher für TA-FB720R
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Sony Verstärker Handbücher
Sony
Sony XM-3001SXD - Stereo Power Amplifier Bedienungsanleitung
Sony
Sony AV650G Bedienungsanleitung
Sony
Sony TAE-8450 Bedienungsanleitung
Sony
Sony EA-80 Bedienungsanleitung
Sony
Sony TA-H4800 Bedienungsanleitung
Sony
Sony TA-VE110 Bedienungsanleitung
Sony
Sony TA-D909 Bedienungsanleitung
Sony
Sony XM-1600GSD Marketing Specifications,... Bedienungsanleitung
Sony
Sony TA-E741 Bedienungsanleitung
Sony
Sony TA-P9000ES - Amplifier Bedienungsanleitung
Sony
Sony STR-NX5MD Bedienungsanleitung
Sony
Sony XES-M50 Bedienungsanleitung
Sony
Sony XM-SD22X Bedienungsanleitung
Sony
Sony TA-AV661 Bedienungsanleitung
Sony
Sony XM-4501 Bedienungsanleitung
Sony
Sony TA-FLX9W Bedienungsanleitung
Sony
Sony XM-GTX1302 Bedienungsanleitung
Sony
Sony XM-GTR2202 Bedienungsanleitung
Sony
Sony TA-F501ES Bedienungsanleitung
Sony
Sony TA-FA5ES Bedienungsanleitung
