Sony CDX-C90R Bedienungsanleitung

– 1 –

SERVICE MANUAL

Model Name Using Similar Mechanism CDX-C780R

CD Drive Mechanism Type MG-363S-121

Optical Pick-up Name KSS-520A

SPECIFICATIONS

CD player section

System Compact disc digital audio

system

Signal-to-noise ratio 109 dB

Frequency response 5 - 20,000 Hz (±1 dB)

Wow and flutter Below measurable limit

Laser Diode Properties

Material GaAlAs

Wavelength 780 nm

Emission Duration Continuous

Laser output power Less than 44.6 µW*

*This output is the value measured at a distance of

200 mm from the objective lens surface on the Optical

Pick-up Block.

Tuner section

Tuning range 87.5 - 108.0 MHz

Antenna terminal External antenna connector

Intermediate frequency 10.7 MHz

Usable sensitivity 8 dBf

Selectivity 75 dB at 400 kHz

Signal-to-noise ratio 65 dB (stereo),

68 dB (mono)

Harmonic distortion at 1 kHz

0.3% (stereo),

0.3% (mono)

Separation 35 dB at 1 kHz

Frequency response 20 - 15,000 Hz

MW/LW

Tuning range MW : 531 - 1,602 kHz

LW : 153 - 281 kHz

Antenna terminal External antenna connector

Intermediate frequency 10.71 MHz/450 kHz

Sensitivity MW : 30 dBµV

LW : 33 dBµV

General

Outputs Digital output

Line outputs (3)

Power antenna relay

control lead

Power amplifier control

lead

Telephone ATT control

lead

Illumination control lead

Tone controls Bass ±8 dB at 100 Hz

Treble ±8 dB at 10 kHz

Power requirements 12 V DC car battery

(negative ground)

Dimensions Approx. 178 ×50 ×184 mm

(w/h/d)

Mounting dimension Approx. 182 ×53 ×163 mm

(w/h/d)

Mass Approx. 1.6 kg

Supplied accessories Parts for installation and

connections (1 set)

Rotary remote RM-X90 (1)

Wireless remote RM-X9R (1)

Front panel case (1)

Design and specifications are subject to change without

notice.

CDX-C90R

AEP Model

UK Model

FM/MW/LW COMPACT DISC PLAYER

MICROFILM

– 17 –

3-1. IC PIN DESCRIPTIONS

• IC5 CXP84640-011Q (CD SYSTEM CONTROL)

Pin No. Pin Name I/O Pin Description

1 – 5 NCO — Not used in this set.

6 FP OPEN I Front panel open detection input

7 FP CLOSE O Front panel close control output

8 LINKOFF I Bus interface link input (Not used in this set.)

9 DRV OE O Focus/tracking coil/sled motor control output

10 D SW I Down switch input (SW4)

11 – 13 NCO — Not used in this set.

14 LM EJ O Loading motor control output

15 LM LOD O Loading motor control output

16 EMPH O O De-emphasis ON/OFF control output

17 CDMON O CD mechanism deck power control output

18 CD ON O CD power control output

19 AMUT O System attenuate control output

20 LD ON O Laser power ON/OFF control output

21 CD RST O CD system reset output

22 – 24 — — Not used in this set.

25 PH3 I Not used in this set.

26 TSTIN0 I Not used in this set.

27 TSTIN1 I Not used in this set.

28 TST CLV I Not used in this set.

29 NCO — Not used in this set.

30 RESET I System reset input (“L” = Reset)

31 X IN I X’tal oscillator input of system clock. (10 MHz)

32 X OUT O X’tal oscillator output of system clock. (10 MHz)

33 GND — Analog GND

34 XT OUT O Not used in this set.

35 XT IN I Not used in this set.

36 AVSS — A/D converter GND

37 AVREF I A/D converter reference voltage input

38 TEP L I Not used in this set.

39 TEP H I Not used in this set.

40 NCO — Not used in this set.

41 PH2 I Not used in this set.

42 SCLK O CD-TEXT data read clock output

43 ESPXQOK O XQOK signal output to DRAM controller.

44 ESPSDT I Serial data input from DRAM controller.

45 GRSRST O Reset signal output to DRAM controller.

46 GRSCOR I Sub-cord sync input from DRAM controller.

47 CD XLAT O CD signal process serial latch output

48 TX CLK O EEPROM serial clock output

49 TX DATA O EEPROM serial data output

50 UNISO O Not used in this set.

51 BUS CLK I/O Bus system serial clock input/output

52 BUS SI I Bus system serial interface input

53 BUS SO O Bus system serial interface output

54 F OK I Focus OK signal input

55 GFS I GFS signal detection input

56 SCOR O Sub-cord sync output

57 SENS I SENS signal input

58 — I Fixed at “H” in this set.

59 CD CKO O CD signal process serial clock output

SECTION 3

DIAGRAMS

– 18 –

Pin No. Pin Name I/O Pin Description

60 BU.IN I Back-up power detection input

61 BUSON I Bus on control input

62 IN SW I Disc in switch input (SW1)

63 SELF SW I Self switch input (SW2)

64 TX CE O EEPROM chip enable output

65 SCK2 O Sub Q read clock output

66 SI2 I Sub Q 80 bit, PCM peak and level data 16 bit input

67 CD DATA O CD signal process serial data output

68 ESPXWRE O Write signal output to DRAM controller.

69 ESPXRDE O Read signal output to DRAM controller.

70 ESPXLT O Serial data latch output to DRAM controller.

71 ESPXSOE O XSOE signal output to DRAM controller.

72 VDD — Power supply

73 HIN I Fixed at “H” in this set.

74 TEXT.ON/OFF I Fixed at “H” in this set.

75 PH1 I Not used in this set.

76 FBTBSEL I Not used in this set.

77 CDOSEL I Not used in this set.

78 – 80 — — Not used in this set.

– 19 –

• IC501 CXD2548R (DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR)

Pin No. Pin Name I/O Pin Description

1 SYSM I System mute input (Not used.)

2 RMUT1 O R-ch, “0” detection output. (“H” : ON, “L” : OFF) (Not used.)

3 LMUT2 O L-ch, “0” detection output. (“H” : ON, “L” : OFF) (Not used.)

4 CKOUT O Master clock frequency division output (Not used.)

5 VDD0 — Digital power supply

6 SBSO O Serial output of sub-P to W.

7 EXCK I Clock input for SBSO read output.

8 SQCK I Clock input for SQSO read output.

9 SQSO O SubQ 80 bit, PCM peak and level data 16 bit output.

10 SENS O SENS output. Output to CPU.

11 SCLK I Clock input for SENS real data read.

12 DATA I Serial data input from CPU.

13 XLAT I Latch input from CPU. Latch serial data at the falling edge.

14 CLOK I Serial data transfer clock input from CPU.

15 XRST I System reset (“L” : Reset)

16 ACDT O Not used.

17 PWM1 I External control input of spindle motor.

18 XLON O Microcomputer extension interface (Output) (Not used.)

19 SPOA I Microcomputer extension interface (InputA) (Not used.)

20 WFCK O WFCK (Write Flame Clock) output

21 GTOP O GTOP output

22 XUGF O XUGF output (Not used.)

23 XPCK O XPLCK output (Not used.)

24 GFS O GFS output

25 RFCK O RFCK output

26 C2PO O C2PO output (Not used.)

27 XROF O XROF output

28 SCOR O “H” output at either detection, sub code sync S0 or S1.

29 MNT0 O MNT0 output (Not used.)

30 MNT1 O MNT1 output (Not used.)

31 MNT3 O MNT3 output (Not used.)

32 VSS1 — Digital GND

33 DOUT O Digital-Out output

34 ATSK I For anti-shock.

35 MIRR O Mirror signal output (Not used.)

36 DFCT O Diffect signal output (Not used.)

37 FOK O Focus OK signal output

38 VDD1 — Digital power supply

39 VPCO1 O Charge pump output for wideband EFM PLL.

40 VPCO2 O VCO2 charge pump output for wideband EFM PLL.

41 VCK.I I VCO2 oscillator input for wideband EFM PLL.

42 V16M O VCO2 oscillator output for wideband EFM PLL.

43 VCTL I VCO2 control input for wideband EFM PLL.

44 PCO O Charge pump output for master PLL.

45 FILO O Filter output for master PLL (Slave = digital PLL).

46 FILI I Filter input for master PLL.

47 AVSS4 — Analog GND

48 CLTV I VCO control voltage input for master.

49 AVDD4 — Analog power supply

50 RFAC I EFM signal input

51 BIAS I Asymmetry circuit constant current input

52 ASY.I I Asymmetry comparate voltage input

– 20 –

Pin No. Pin Name I/O Pin Description

53 ASY.O O EFM full-swing output (“L” : VSS, “H” : VDD)

54 VC I Center voltage input

55 FE I Focus error signal input

56 SE I Sled error signal input

57 TE I Tracking error signal input

58 CE I Center error signal input

59 RFDC I RF signal input

60 RFC I Condenser connection pin for LPF time constant of RF signal.

61 ADIO O OP amplifier output (Not used.)

62 AVSS3 — Analog GND

63 IGEN I Current source reference resistor connection for OP amplifier.

64 AVDD3 — Analog power supply

65, 66 TES2, 3 I TEST pin (Fixed at “L”.)

67 VSS2 — Digital GND

68 TEST I TEST pin (Fixed at “L”.)

69 SFDR O Sled drive output

70 SRDR O Sled drive output

71 TFDR O Tracking drive output

72 TRDR O Tracking drive output

73 FFDR O Focus drive output

74 FRDR O Focus drive output

75 VDD2 — Digital power supply

76 COUT O Track number count signal output (Not used.)

77 LOCK O Not used.

78 MDS O Servo control output of spindle motor. (Not used.)

79 MDP O Servo control output of spindle motor.

80 SSTP I Disc most inner track detection signal input

81 FSTO O 2/3 frequency division output of pins 103 and 104.

82 FSTI I Reference clock input for digital servo.

83 XTSL I X’tal select input (“L” : 16.9344 MHz)

84 C4M O 4.2336 MHz output

85 WDCK O D/A interface. Word clock f = 2Fs

86 VDD3 — Digital power supply

87 LRCK O D/A interface. LR clock f = Fs

88 LRCKI I LR clock input to DAC. (48 bit slot) (Not used.)

89 PCMD O D/A interface. Serial data (2’s COMP, MSB first)

90 PCMDI I Audio data input to DAC. (48 bit slot) (Not used.)

91 BCK O D/A interface. Bit clock

92 BCKI I Bit clock input to DAC. (48 bit slot) (Not used.)

93 EMPH O Not used.

94 EMPHI I De-emphasis ON/OFF of DAC. (“H” : ON, “L” : OFF) (Not used.)

95 VSS3 — Digital GND

96 AVSS1 — L-ch, Analog GND.

97 AVDD1 — L-ch, Analog power supply.

98 AOUT1 O L-ch, Analog output. (Not used.)

99 AIN1 I L-ch, OP amplifier input. (Not used.)

100 LOUT1 O L-ch, LINE output. (Not used.)

101 AVSS1 — L-ch, Analog GND.

102 XVDD — Analog power supply for master clock.

103 XTAI I X’tal oscillator input of master clock (16.9344 MHz).

104 XTAO O X’tal oscillator output of master clock. (Not used.)

105 XVSS — Analog GND for master clock.

106 AVSS2 — R-ch, Analog GND.

– 21 –

Pin No. Pin Name I/O Pin Description

107 ROUT2 O R-ch, LINE output. (Not used.)

108 AIN2 I R-ch, OP amplifier input. (Not used.)

109 AOUT2 O R-ch, Analog output. (Not used.)

110 AVDD2 — R-ch, Analog power supply.

111 AVSS2 — R-ch, Analog GND.

112 VSS0 — Digital GND

– 22 –

• IC300 MB90F574PFV-G-140-BND (SYSTEM CONTROL)

Pin No. Pin Name I/O Pin Description

1 TIR WR O TIR IC data write output

2 TIR RD O TIR IC data read output

3 TIR CE O TIR IC data chip enable output

4 TIR CE O XTIR IC data chip enable output

5 TIR BUSY I TIR IC busy input

6 TIR PDOWN O TIR IC power down output

7 DIVER O FM diversity ON/OFF output (Not used in this set.)

8 VCC — Power supply pin (+5 V)

9 AF SEEK O AF SEEK output

10 WIDE O WIDE/NARROW select output

11 CAUTION I Caution alarm setting (Fixed at “H” in this set.)

12 NOSE SW I Nose detection input

13 COLOR O Color control output (“H”:green, “L”:amber)

14 BUSON O Bus ON control output

15 BEEP O BEEP output

16 TIR RES O TIR IC reset (Power down) output

17 DF LAT O Digital filter latch output

18 DF SO O Digital filter serial data output

19 DF CKO O Digital filter clock output

20 UNISI I Serial data input (for SONY BUS)

21 UNISO O Serial data output (for SONY BUS)

22 UNICK O Serial clock output (for SONY BUS)

23 NCO — Not used.

24 SIRCS I Remote commander input

25 PLLSI I PLL data input

26 PLLSO O PLL data output

27 PLLCKO O PLL clock output

28 PLL CE O PLL chip enable output

29 P MOT+ O Front panel motor control (+) output

30 P MOT– O Front panel motor control (–) output

31 I DET I Panel motor lock detection input

32 POS0 I Position detection input 0 (Open end)

33 GND — GND

34 C — Power stabilization capacitor pin

35 POS1 I Position detection input 1 (Close end)

36 POS2 I Position detection input 2 (10 DEG.)

37 POS3 I Position detection input 3 (20 DEG.)

38 DVCC — D/A converter VREF input

39 DVSS — GND of D/A converter.

40 MOTREF O Motor reference voltage output

41 LCDANG O LCD view angle adjustment analog output

42 AVCC — Analog power supply pin (+5 V)

43 AVRH — A/D converter VREF+ input

44 AVRL — A/D converter VREF– input

45 AVSS — Analog GND

46 DSTSEL0 I Destination select input 0 (Fixed at “H” in this set.)

47 H TEMP I High templature detection analog input (Fixed at “H” in this set.)

48 LTEMP I Low templature detection analog input (Fixed at “H” in this set.)

49 MPT I Tuner multi-pass input

50 VSM I S-Meter voltage detection input

51 RC IN0 I Rotary commander input 0

52, 53 KEYIN0, 1 I Key input 0, 1

– 23 –

Pin No. Pin Name I/O Pin Description

54 VCC — Power supply pin (+5 V)

55 RAMBU I RAM reset detection input

56 TESTIN I Test mode setting detection input

57 AD ON O Power control output of A/D conversion.

58, 59 RE IN0, 1 I Rotary encoder input 0, 1

60 BOOT I Compulsory boot mode input

61 DIMMER O Dimmer control output

62 TIR IND O TIR indicator control output

63 GND — GND

64 SYSRST O System reset output

65, 66 NCO — Not used.

67 EEDATA I/O EEPROM serial data input/output

68 EECLK O EEPROM serial clock output

69 NCO — Not used.

70 RDSSI I RDS serial clock input

71 RDSCKO I RDS serial data input

72 DAVN I RDS IC data taking in detection input

73 X0A — Low speed oscillation input (32.768 kHz)

74 X0B — Low speed oscillation input (32.768 kHz)

75 RC IN1 I Rotary commander input

76 BU IN I Back-up power detection input

77 KEY ACK I Key input acknowledge

78 ILLIN I Illumination line detection input

79 TELATT I Telephone mute detection input

80 NCO — Not used.

81 ACC IN I Accessory power detection input

82 EMPH I I Emphasis input

83 FP CLOSE I Front panel close detection input

84 FP OPEN O Front panel open control output

85 BOOT DP O Display controller boot mode control output

86 HSTX — Connect to power supply pin.

87 MD2 — Connect to GND.

88, 89 MD0, 1 — Connect to power supply pin.

90 RESET I Microcomputer reset input

91 VSS — GND

92 X0 — High speed oscillation input (3.68 MHz)

93 X1 — High speed oscillation input (3.68 MHz)

94 VCC — Power supply pin (+5 V)

95 TIMPOL O Time poling setting (Fixed at “H” in this set.)

96 PW ON O System power control output

97 ILL ON O Illumination power control output

98 DIRECT O Direct volume control output

99 ATT O System mute control output

100 ANTREM O Antenna remote control output

101 VOLCE0 O Input selector/tone/sub volume serial chip enable output

102 VOLCE1 O Electric volume serial chip enable output (L-CH)

103 VOLCE2 O Electric volume serial chip enable output (R-CH)

104 VOLCKO O Volume serial clock output

105 VOLSO O Volume serial data output

106 ENC+ I Rotary commander and encoder input (+)

107 ENC– I Rotary commander and encoder input (–)

108 FM ON O FM ON control output

109 AM ON O AM ON control output

– 24 –

Pin No. Pin Name I/O Pin Description

110 SEEKOUT O SEEK OUT output

111 AM STIN I AM stereo input (Not used in this set.)

112 FM STIN I/O Used in conjunction with stereo input/monaural output (FM mode)

113 SD IN I Signal detector input

114 TU ATT O Tuner mute output

115 TIR D0 I/O TIR IC data 0 input/output

116 TIR D1 I/O TIR IC data 1 input/output

117 TIR D2 I/O TIR IC data 2 input/output

118 TIR D3 I/O TIR IC data 3 input/output

119 VSS — GND

120 TIRPLAY O TIR IC play mode audio select control output

– 25 –

• IC500 HD6413002F16 (DISPLAY CONTROL)

Pin No. Pin Name I/O Pin Description

1 VDD — Power supply pin (+5 V)

2 SIRCS I Remote commander input

3 SIRCS I Remote commander input

4 LCD-RST O LCD controller reset control output

5 ILL ON O LCD controller power supply control output

6 EL ON O LCD back light EL power supply control output

7 LCD-ST O LCD controller information start request signal output

8 CS-CTL O SRAM master chip enable control output (Not used in this set.)

9 BOOTI I Compulsory boot mode input

10 (RESO) O Connect to GND.

11 VSS O GND

12 LCD-SO O LCD controller serial data output

13 UNI-SO O BUS interface data output

14 LCD-RX I LCD controller serial data input

15 UNI-SI I BUS interface data input

16 UNI-CO O LCD controller serial clock ouput

17 UNI-CI I LCD controller serial clock input

18 – 21 D0 – D3 I/O External RAM, ROM data bus input/output

22 VSS — GND

23 – 34 D4 – D15 I/O External RAM, ROM data bus input/output

35 VDD — Power supply pin (+5 V)

36 – 43 A0 – A7 O External RAM, ROM address bus output

44 VSS — GND

45 – 56 A8 – A19 O External RAM, ROM address bus output

57 VSS — GND

58 WAIT O Not used.

59 (P61) — Not used.

60 (P62) — Not used.

61 NC — Not used.

62 STBY I Hardware standby input (Fixed at “H”.)

63 SYSRST I Reset input

64 BU-IN I Back-up power detection input

65 VSS — GND

66 EXTAL O Oscillation output (14.74 MHz)

67 XTAL I Oscillation input (14.74 MHz)

68 VDD — Power supply pin (+5 V)

69 AS — Not used.

70 RD O Read signal output

71 HWR O High write signal output

72 LWR O Low write signal output

73 MD0 I Microcomputer operation mode input (Fixed at “L”.)

74 MD1 I Microcomputer operation mode input (Fixed at “L”.)

75 MD2 I Microcomputer operation mode input (Fixed at “H”.)

76 AVDD I A/D converter power supply input

77 VREF I A/D converter reference voltage input

78 – 83 (AN0 – AN5) — Connect to GND.

84 BU-IN I Back-up power detection input

85 PBS I Parking brake input

86 AVSS — A/D converter GND

87 BUS-ON I BUS-interface BUS-ON input

88 SRAM-CS O SRAM chip enable output

89 DEC-CS O Demodulator LSI chip enable output (Not used in this set.)

Andere Handbücher für CDX-C90R

Inhaltsverzeichnis

Andere Sony Autoempfänger Handbücher

Sony

Sony XR-CA320 Bedienungsanleitung

Sony

Sony CDX-C910RDS Produkthandbuch

Sony

Sony CDX-GT42IPW - Fm/am Compact Disc Player Bedienungsanleitung

Sony

Sony HCD-DZ300 Bedienungsanleitung

Sony

Sony XR-6380 Bedienungsanleitung

Sony

Sony MEX-DV1000 - Cd/dvd Receiver, Mp3/wma Player Bedienungsanleitung

Sony

Sony CDX-G2050UP Bedienungsanleitung

Sony

Sony CDX-F7000 - Fm/am Compact Disc Player Bedienungsanleitung

Sony

Sony GT120 - CDX Radio / CD Player Produkthandbuch

Sony

Sony XR-3304 Bedienungsanleitung

Sony

Sony XR-C113 Produkthandbuch

Sony

Sony CDX-CA400 - Compact Disc Changer System Bedienungsanleitung

Sony

Sony CDX-GT40UW Bedienungsanleitung

Sony

Sony CDX-GT31W - Fm/am Compact Disc Player Produkthandbuch

Sony

Sony CDX-F5510 (XT-XM1) Bedienungsanleitung

Sony

Sony CDX-GT350MP - Fm/am Compact Disc Player Bedienungsanleitung

Sony

Sony CDX-C480 - Fm/am Compact Disc Player Produkthandbuch

Sony

Sony CDX-GT500 - Fm/am Compact Disc Player Bedienungsanleitung

Sony

Sony CDX-A250EE Bedienungsanleitung

Sony

Sony XR-C9100R Bedienungsanleitung

Sony

Sony AVD-S50ES - Single Disc Dvd/sacd™/cd... Benutzerhandbuch

Sony

Sony CDX-3170 Bedienungsanleitung

Sony

Sony CDX-3700 Bedienungsanleitung

Sony

Sony MDX-40 Referenzhandbuch

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung

Philips

Philips CEM5000 Bedienungsanleitung