Sony JunboTron JME-SA200 Bedienungsanleitung

JumboTron

Screen Alignment

Controller

3-864-808-13 (1)

Operating Instructions

Before operating the unit, please read this manual

thoroughly and retain it for future reference.

1998 by Sony Corporation

JME-SA200

Ver.02.50

2Table of Contents

For the customers in the U.S.A.

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

Owner’s Record

The model and serial numbers are located on the rear.

Record the serial number in the space provided below.

Refer to these numbers whenever you call upon your Sony

dealer regarding this product.

Model No. JME-SA200 Serial No. _______________

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified

personnel only.

Table of Contents 3

(continued)

Table of Contents

Overview

About This Manual ............................................................ 5

Precautions ........................................................................ 5

Overview of the JumboTron System ............................... 6

Images to be displayed on the JumboTron screen ..................6

Structure of the JumboTron screen .........................................7

Configuration of the JumboTron system ................................8

Features.............................................................................. 9

Locations and Functions of Parts and Controls

Locations and Functions of Parts and Controls .......... 10

Power Source and Connections

Power Source................................................................... 11

Attaching the battery pack ....................................................11

Detaching the battery pack....................................................12

Connections..................................................................... 13

JumboTron system configuration..........................................13

Connections for using as wireless controller ........................14

Connections for using as wired controller ............................16

Registering the Phone Number for the Modem ............ 17

Attaching the Shoulder Strap......................................... 19

Before Adjustment

Preparing the System...................................................... 20

Communicating with the ICU Controller ....................... 21

When the unit is used as wireless controller .........................21

When the unit is used as wired controller .............................22

Registering and Selecting the ICU................................. 23

Registering the ID number of the ICU..................................23

Selecting the ICU ..................................................................25

Setting the Information about the Screen ..................... 26

Selecting the Screen Display Mode and Input Signal .. 28

4Table of Contents

Table of Contents

Adjustment

Adjusting the Image Position and Size on the Screen. 29

Adjusting the position and size of the image ........................29

Selecting the memory number/adjusting the screen by

recalling the stored conditions .........................................31

Adjusting the Picture on the Screen.............................. 32

Checking the input signal and picture quality.......................32

Adjusting the color, hue and sharpness.................................33

Adjusting the Brightness of the Screen ........................ 34

Adjusting the Computer Graphics and Video Image

Mix Level .......................................................................... 35

Adjusting the mix level .........................................................35

Checking the Screen Display Unit ................................. 37

Adjusting the Luminance of a Specified Unit or Cell ... 39

Resetting the Luminance of a Unit to the Factory

Data................................................................................... 44

Registering and Recalling the Unit/Cell Numbers........ 46

Registering the unit/cell number ...........................................46

Recalling the registered unit or cell ......................................48

Adjusting the Monitor ..................................................... 50

Adjusting the position and boundary of the image on the

monitor.............................................................................50

Selecting the memory number/adjusting the monitor by

recalling the stored conditions .........................................52

Cutting Off the Image from the Screen.......................... 53

Displaying the Unit Address on the Screen.................. 54

Displaying the Software Version of the JME-SA200 .... 55

Others

Troubleshooting .............................................................. 56

Specifications .................................................................. 57

Overview 5

AboutThis Manual

This instruction manual is mainly aimed at maintenance/service personnel.

It explains how to use the JME-SA200 screen alignment controller, which

is used to install and adjust the screen of the JumboTron system.

The screen alignment controller is used in combination with the JTC-P200

image control unit (ICU) and JTC-C200 ICU controller. As this manual

explains how to use the JTC-P200 and JTC-C200 only briefly, please refer

to the Operating Instructions of the JTC-C200 for details.

Precautions

On safety

•Do not use the unit at extremely high or low temperatures.

•Do not use the unit in high humidity.

If any abnormality occurs, turn off the power and consult with qualified

Sony service personnel.

On cleaning

Clean the case and front panel with a dry soft cloth, or a soft cloth slightly

moistened with a mild detergent solution. Do not use any organic solvents,

such as alcohol or benzene, which might damage the finish.

6Overview

The JumboTron system displays video images on a large screen

(JumboTron screen) located either outdoors or indoors. Images from video

sources such as a VCR, video camera and computer can be displayed on

the screen.

The JumboTron system provides superb bright images with high

resolution, regardless of whether it is day or night, indoors or outdoors.

Images to be displayed on the JumboTron screen

The JumboTron system can display the following three types of images:

[a] Video images input from equipment such as a VCR, video camera

and video disc (INPUT 1)

[b] Computer graphics (INPUT 2)

[c] Mixed images of INPUT 1 and INPUT 2

(INPUT 1 images are superimposed on the monochrome area of the

INPUT 2 images.)

Overview of the JumboTron System

[a] INPUT 1 [b] INPUT 2

[c] Mixed images

INPUT 2

INPUT 1

Mixed images

Overview 7

Structure of the JumboTron screen

The basic element of the JumboTron screen is an RGB trio (dot).

A “cell” consists of the dots arranged at a certain interval (picture element

pitch) and a “unit (JumboTron display unit)” consists of cells.

There are two unit types, the LDU-15 series (with 15-mm pitch) and the

LDU-30 series (with 30-mm pitch). You can configure a large JumboTron

screen by arranging the JumboTron display units vertically and

horizontally to suit various uses or locations. An example structure of each

series is as follows:

LDU-15 series

Picture element pitch

4 dots

RGB trio

(dot)

Cell

Unit

JumboTron screen

4 cells

(16 dots)

4 cells (16 dots)

NTSC:

max. 30 units

(120 cells =

480 dots)

PAL:

max. 36 units

(144 cells =

576 dots)

NTSC: max. 40 units (160 cells = 640 dots)

PAL: max. 48 units (192 cells = 768 dots)

LDU-30 series

NTSC: max.

30 units

(480 dots)

PAL: max.

36 units

(576 dots)

B R G

RGB trio (dot)

Picture element pitch

Cell

4 dots

2 dots

Block

2 cells (8 dots)

4 cells (8 dots)

Unit

4 blocks (32 dots)

2 blocks

(16 dots)

JumboTron screen

NTSC: max. 20 units (640 dots)

PAL: max. 24 units (768 dots)

8Overview

Configuration of the JumboTron system

The following is the suggested configuration of the JumboTron system.

Control room

Computer

VCR

Still image player

Video presenter

TV tuner

Video disc player

DVD player

Video camera

AV switcher

Microphone

Audio amplifier Speaker system

Frame

synchronizer

Screen site

Computer

JTC-C200 ICU

controller

Monitor Modem

JME-UA200

unit alignment

controller JumboTron screen

JTA-LS200

ABC sensor

unit

JTC-P200 image

control unit (ICU)

Power source

JME-SA200

screen

alignment

controller

Cellular

phone

Public

telephone

line

Digital

data

card

Audio mixer

Monitor

Overview of the JumboTron System

Overview 9

Features

The JME-SA200 screen alignment controller is designed to check the

operation of the JumboTron screen and to adjust the position, size,

brightness and picture quality of the image. The wireless remote control

system using the public telephone system assures reliable data

communication.

The main functions of the JME-SA200 are as follows:

Wireless remote controller using a cellular phone

Interactive data communication is carried out via the cellular phone

connected to the JME-SA200 and the modem connected to the JTC-C200

ICU controller. This data communication method using the public

telephone system offers a highly reliable wireless remote control system.

The JME-SA200 can also be used as a wired remote controller by

connecting to the ICU controller using a connecting cable (with a

maximum cable length of 1,000 m).

Checking the operation of the screen

Activating the test signal generator built in the display units which

constitute the screen, the JME-SA200 displays the stair step and color bar

signals on the screen for checking the operation of each display unit.

Adjusting the luminance of a specified unit or cell

The JumboTron screen may partially degrade the brightness or color

uniformity after long use. The JME-SA200 can correct the uniformity by

adjusting the luminance or color temperature of a specified unit or cell.

Adjusting the position and size of the image

The JME-SA200 can shift the image on the screen vertically or

horizontally, and change the image size (expansion/reduction level). The

JME-SA200 automatically calculates and displays the aspect ratio of the

adjusted image.

The adjusted data can be stored in the memory of the ICU, and recalled

instantly by specifying the memory number.

Adjusting the brightness of the image

The JME-SA200 can adjust the brightness of the whole screen to 16 levels.

Setting the area of a computer graphics image mixed with a

video image

When displaying a video image over the monochrome portion of a

computer graphics image, the JME-SA200 can specify the area to be

mixed as R, G and B data.

Adjusting the picture quality on the screen

The JME-SA200 can adjust the color, hue and sharpness of the image on

the screen.

Storing up to 256 unit or cell numbers

The JME-SA200 can register up to 256 unit or cell numbers to be adjusted

or repaired to store these numbers in the memory of the ICU.

10 OverviewLocations and Functions of Parts and Controls

Locations and Functions of Parts and Controls

1EJECT (card eject) button (inside)

To eject the digital data card, press the EJECT button

inside the unit using the supplied eject tool.

2PC CARD (digital data card) slot

Insert the digital data card.

3LCD display window

4Function buttons (F1 – F5)

The functions of the buttons change with the stage of

the operation. The current functions are indicated at

the bottom of the display window.

For details, see each section.

5MENU button

Returns to the upper directory of the menu.

6CURSOR v/V/B/bbuttons

Select the menu items in the display window or change

the set values.

7ENTER button

Confirms the selected item and stores the set value.

6CONTROL connector (D-sub 15-pin)

Connect to the CONTROL 2 connector of the JTC-

C200 ICU controller for wired control.

Front panel

Rear panel

!º !¡

!™

!£

!¢

!¡

9LCD DISPLAY switch

Turns on/off the backlight of the LCD display window.

The battery life will be longer if the backlight is turned

off.

0Connector guard

Note

Use a connector whose size is smaller than the

connector guard.

!¡ Shoulder strap attachments

Attach the supplied shoulder strap here. Two sets of

the attachments are provided at the top and bottom of

the unit.

!™ POWER switch

Turns the unit on/off.

!£ Battery pack compartment

Attach the NP-F750 rechargeable battery pack (not

supplied) here.

!¢ BATT EJECT (battery eject) lever

Press this lever downward to unlock the battery pack

and remove it.

Inhaltsverzeichnis

Andere Sony Controller Handbücher

Sony

Sony RM-TP1 Operating Instructions / Mode... Bedienungsanleitung

Sony

Sony HKSP-300 Bedienungsanleitung

Sony

Sony ZRD-1 Bedienungsanleitung

Sony

Sony PlayStation DualSense CFI-ZCT1G Bedienungsanleitung

Sony

Sony RM-NS1000 Bedienungsanleitung

Sony

Sony PS4 DUALSHOCK 4 Bedienungsanleitung

Sony

Sony ICF-SC1PC Bedienungsanleitung

Sony

Sony UPA-PC500 Bedienungsanleitung

Sony

Sony ZRD-C12A Bedienungsanleitung

Sony

Sony HKSP-R80 Bedienungsanleitung

Sony

Sony DSBK-2020 Bedienungsanleitung

Sony

Sony CPH-10010U/97026 Bedienungsanleitung

Sony

Sony RCC1000 Bedienungsanleitung

Sony

Sony BKM-36H Bedienungsanleitung

Sony

Sony BKSI-2440 Series Bedienungsanleitung

Sony

Sony Jumbotron JME-UA200 Bedienungsanleitung

Sony

Sony RM-E300 Bedienungsanleitung

Sony

Sony HKDV-503 Bedienungsanleitung

Sony

Sony RM-V301 Bedienungsanleitung

Sony

Sony PlayStation DualSense Edge Bedienungsanleitung

Sony

Sony RM-VZ220 Bedienungsanleitung

Sony

Sony HomeShare RMN-U1 Bedienungsanleitung

Sony

Sony HomeShare RMN-U1 Bedienungsanleitung

Sony

Sony HomeShare RMN-U1 Installationsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch